Nissan Sentra. Manual - part 112

BCS-18

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

WORK SUPPORT

*: Initial setting

HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)

INFOID:0000000009757311

DATA MONITOR

ACTIVE TEST

TRNK/HAT MNTR [On/Off]

Indicates condition of trunk room lamp switch.

RKE-LOCK [On/Off]

Indicates condition of lock signal from Intelligent Key.

RKE-UNLOCK [On/Off]

Indicates condition of unlock signal from Intelligent Key.

Monitor Item [Unit]

Description

Test Item

Description

INT LAMP

This test is able to check interior room lamp operation [On/Off].

Support Item

Setting

Description

R LAMP TIMER LOGIC SET

MODE 2

Interior room lamp timer activates with all doors.

MODE 1*

Interior room lamp timer activates with the driver door only.

SET I/L D-UNLCK INTCON

On*

Interior room lamp timer function ON.

Off

Interior room lamp timer function OFF.

ROOM LAMP TIMER SET

MODE 4

30 sec.

Sets the interior room lamp ON time. (Timer operating time).

MODE 3* 15 sec.

MODE 2

7.5 sec.

Monitor Item [Unit]

Description

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

ENGINE STATE [Stop/Stall/Crank/Run]

Indicates engine status received from ECM on CAN communication line.

VEH SPEED 1 [km/h]

Indicates vehicle speed signal received from ABS on CAN communication line.

TURN SIGNAL R [On/Off]

Indicates condition of combination switch.

TURN SIGNAL L [On/Off]

TAIL LAMP SW [On/Off]

HI BEAM SW [On/Off]

HEAD LAMP SW 1 [On/Off]

HEAD LAMP SW 2 [On/Off]

PASSING SW [On/Off]

AUTO LIGHT SW [On/Off]

FR FOG SW [On/Off]

DOOR SW-DR [On/Off]

Indicates condition of front door switch LH.

DOOR SW-AS [On/Off]

Indicates condition of front door switch RH.

DOOR SW-RR [On/Off]

Indicates condition of rear door switch RH.

DOOR SW-RL [On/Off]

Indicates condition of rear door switch LH.

DOOR SW-BK [On/Off]

Indicates condition of trunk switch.

OPTI SEN (DTCT) [V]

Indicates outside brightness voltage signal from optical sensor.

OPTI SEN (FILT) [V]

Indicates outside brightness voltage signal from optical sensor filtered by BCM.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-19

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

WORK SUPPORT

*: Initial setting

WIPER
WIPER : CONSULT Function (BCM - WIPER)

INFOID:0000000009757312

DATA MONITOR

Test Item

Description

FR FOG LAMP

This test is able to check front fog lamp operation [On/Off].

HEAD LAMP

This test is able to check head lamp operation [Hi/Low/Off].

ILL DIM SIGNAL

This test is able to check head lamp illumination dimming operation [On/Off].

TAIL LAMP

This test is able to check tail lamp operation [On/Off].

Support Item

Setting

Description

AUTO LIGHT LOGIC SET

MODE 1*

With twilight ON custom & with wiper INT, LO and HI

MODE 2

Witt twilight ON custom & with wiper LO and HI

MODE 3

With twilight ON custom & without

MODE 4

Without twilight ON custom & with wiper INT, LO and HI

MODE 5 

Without twilight ON custom & with wiper LO and HI

MODE 6

Without twilight ON custom & without

BATTERY SAVER SET

On*

Exterior lamp battery saver function ON.

Off

Exterior lamp battery saver function OFF.

CUSTOM A/LIGHT SETTING

MODE 1*

Normal

MODE 2

More sensitive setting than normal setting (Turns ON earlier than nor-
mal operation)

MODE 3

More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)

MODE 4

Less sensitive setting than normal setting (Turns ON later than normal 
operation)

ILL DELAY SET

MODE 8

180 sec.

Sets delay timer function operation time
(All doors closed).

MODE 7

150 sec.

MODE 6

120 sec.

MODE 4

60 sec.

MODE 5

90 sec.

MODE 3

30 sec.

MODE 2

OFF

MODE 1* 45 sec.

Monitor Item [Unit]

Description

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

VEH SPEED 1 [km/h]

Indicates vehicle speed signal received from ABS on CAN communication line.

FR WIPER HI [On/Off]

Indicates condition of wiper operation of combination switch.

FR WIPER LOW [On/Off]

FR WASHER SW [On/Off]

FR WIPER INT [On/Off]

FR WIPER STOP [On/Off]

Indicates front wiper auto stop signal received from IPDM E/R on CAN communication 
line.

INT VOLUME [1 

− 7] 

Indicates condition of intermittent wiper operation of combination switch.

BCS-20

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

WORK SUPPORT

* : Initial setting

FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)

INFOID:0000000009757313

DATA MONITOR

ACTIVE TEST

WORK SUPPORT

* : Initial setting

AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER)

INFOID:0000000009757314

DATA MONITOR

Test Item

Description

FR WIPER

This test is able to check front wiper operation [INT/Lo/Hi/Off].

Support Item

Setting

Description

WIPER SPEED SETTING

On

Front wiper intermittent time linked with vehicle speed and wiper dial position.

Off*

Front wiper intermittent time linked with wiper dial position.

Monitor Item [Unit]

Description

REQ SW -DR [On/Off]

Indicates condition of door request switch LH.

REQ SW -AS [On/Off]

Indicates condition of door request switch RH.

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

TURN SIGNAL R [On/Off]

Indicates condition of turn signal function of combination switch.

TURN SIGNAL L [On/Off]

HAZARD SW [On/Off]

Indicates condition of hazard switch.

RKE-LOCK [On/Off]

Indicates condition of lock signal from Intelligent Key.

RKE-UNLOCK [On/Off]

Indicates condition of unlock signal from Intelligent Key.

RKE-PANIC [On/Off]

Indicates condition of panic alarm signal from Intelligent Key.

Test Item

Description

FLASHER

This test is able to check turn signal lamp operation [Off/LH/RH].

Support Item

Setting

Description

HAZARD ANSWER BACK

Lock/Unlock*

Hazard warning lamp activation when doors are locked or unlocked with 
Intelligent Key.

Unlock Only

Hazard warning lamp activation when doors are unlocked with Intelligent 
Key.

Lock Only

Hazard warning lamp activation when doors are locked with Intelligent 
Key.

Off

No hazard warning lamp activation when doors are locked or unlocked 
with Intelligent Key.

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-21

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)

INFOID:0000000009757315

SELF DIAGNOSTIC RESULT

Refer to 

BCS-49, "DTC Index"

.

DATA MONITOR

Monitor Item [Unit]

Description

FAN ON SIG [On/Off]

Indicates condition of fan switch.

AIR COND SW [On/Off]

Indicates condition of A/C switch.

Monitor Item [Unit]

Main

Description

REQ SW -DR [On/Off]

×

Indicates condition of door request switch LH.

REQ SW -AS [On/Off]

×

Indicates condition of door request switch RH.

REQ SW -BD/TR [On/Off]

×

Indicates condition of trunk open switch.

PUSH SW [On/Off]

Indicates condition of push-button ignition switch.

CLUCH SW [On/Off]

Indicates condition of clutch switch.

BRAKE SW 1 [On/Off]

×

Indicates condition of brake switch.

BRAKE SW 2 [On/Off]

Indicates condition of brake switch.

DETE/CANCL SW [On/Off]

×

Indicates condition of P (park) position.

SFT PN/N SW [On/Off]

×

Indicates condition of P (park) or N (neutral) position.

UNLK SEN -DR [On/Off]

×

Indicates condition of driver door unlock sensor.

PUSH SW -IPDM [On/Off]

Indicates condition of push-button ignition switch received from IPDM E/R on 
CAN communication line.

IGN RLY1 -F/B [On/Off]

Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line.

DETE SW -IPDM [On/Off]

Indicates condition of detent switch received from TCM on CAN communication 
line.

SFT PN -IPDM [On/Off]

Indicates condition of P (park) or N (neutral) position from TCM on CAN com-
munication line.

SFT P -MET [On/Off]

Indicates condition of P (park) position from TCM on CAN communication line.

SFT N -MET [On/Off]

Indicates condition of N (neutral) position from IPDM E/R on CAN communica-
tion line.

ENGINE STATE [Stop/Start/Crank/Run]

×

Indicates condition of engine state from ECM on CAN communication line.

VEH SPEED 1 [mph/km/h]

×

Indicates condition of vehicle speed signal received from ABS on CAN commu-
nication line.

VEH SPEED 2 [mph/km/h]

×

Indicates condition of vehicle speed signal received from combination meter on 
CAN communication line.

DOOR STAT -DR [LOCK/READY/UNLK]

×

Indicates condition of driver side door status.

DOOR STAT -AS [LOCK/READY/UNLK]

×

Indicates condition of passenger side door status.

ID OK FLAG [Set/Reset]

Indicates condition of Intelligent Key ID.

PRMT ENG STRT [Set/Reset]

Indicates condition of engine start possibility.

PRMT RKE STRT [Set/Reset]

Indicates condition of engine start possibility from Intelligent Key.

RKE OPE COUN1 [0-19]

×

When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.

RKE OPE COUN2 [0-19]

×

When remote keyless entry receiver receives the signal transmitted while oper-
ating on Intelligent Key, the numerical value start changing.

TRNK/HAT MNTR [On/Off]

Indicates condition of trunk room lamp switch.

RKE-LOCK [On/Off]

Indicates condition of lock signal from Intelligent Key.