Nissan Leaf. Manual - part 1119

B0096 FRONT SIDE AIR BAG SATELLITE SENSOR RH

SRC-77

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

2. Check for DTC using CONSULT.
Is the DTC detected?

YES (Current DTC)>>Refer to 

SRC-77, "Diagnosis Procedure"

.

YES (Past DTC)>>GO TO 2.

NO

>> Inspection End.

2.

ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.
Can the DTC be erased?

YES

>> Inspection End.

NO

>> Refer to 

SRC-77, "Diagnosis Procedure"

.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.

CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-11, "On Board Diagnosis Function"

.

NOTE:

SRS will not enter diagnosis mode if no malfunction is detected in user mode.
Is the DTC detected?

YES

>> Refer to 

SRC-77, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000010877000

1.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

• Visible damage to connector or terminal

• Loose terminal

• Poor connection

NOTE:

All harness connectors should be inspected from the air bag diagnosis sensor unit to the end component

(including in-line connectors).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform one of the following repairs:

• Visible damage: Replace the harness.

• Loose terminal: Secure the terminal.

• Poor connection: Secure the connection.

2.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 3.

NO

>> Refer to 

GI-53, "Intermittent Incident"

.

3.

WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:

The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors).
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace the harness.

4.

CONFIRM DTC

SRC-78

< DTC/CIRCUIT DIAGNOSIS >

B0096 FRONT SIDE AIR BAG SATELLITE SENSOR RH

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 5.

NO

>> Refer to 

GI-53, "Intermittent Incident"

.

5.

SATELLITE SENSOR RH

1. Replace the satellite sensor RH. Refer to 

SR-35, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 6.

NO

>> Clear DTC. Inspection End.

6.

AIR BAG DIAGNOSIS SENSOR UNIT

1. Replace the air bag diagnosis sensor unit. Refer to 

SR-38, "Removal and Installation"

.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 7.

NO

>> Clear DTC. Inspection End.

7.

RELATED HARNESS

Replace the related harness.

>> END

B0098 FRONT DOOR SATELLITE SENSOR RH

SRC-79

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

B0098 FRONT DOOR SATELLITE SENSOR RH

Description

INFOID:0000000010877001

DTC B0098 FRONT DOOR SATELLITE SENSOR RH

The front door satellite sensor RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor

unit will monitor the front door satellite sensor RH for internal failures and its circuits for communication errors.

PART LOCATION

Refer to 

SRC-6, "Component Parts Location"

.

DTC Description

INFOID:0000000010877002

DTC DETECTION LOGIC

POSSIBLE CAUSE

[B0098–11]

• Connection malfunction or short circuit to ground of harness and connector

• Internal malfunction of front door satellite sensor RH

• Internal malfunction of air bag diagnosis sensor unit

[B0098–23, B0098–24, B0098–25, B0098–28]

• Internal malfunction of front door satellite sensor RH

• Internal malfunction of air bag diagnosis sensor unit

[B0098–81, B0098–93]

• Connection malfunction of harness or connector

• Internal malfunction of front door satellite sensor RH

• Internal malfunction of air bag diagnosis sensor unit

[B0098–86]

• Air bag diagnosis sensor unit and front door satellite sensor RH is different from the part specified

[B0098–88]

• Connection malfunction or open circuit of harness and connector

• Internal malfunction of front door satellite sensor RH

• Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE (With CONSULT)

1.

CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.

2. Check the DTC using CONSULT.

DTC

CONSULT screen items

(Trouble diagnosis content)

DTC detecting condition

B0098–11

DOOR SATEL SENS RH 
[Right Frontal Restraints 
Sensor 3 (Subfault)]

[GND-SHORT]

Front door satellite sensor RH circuit is shorted to ground

B0098–23

[LOWER LIMIT ERR]

Lower limit value malfunction of front door satellite sensor RH

B0098–24

[UPPER LIMIT ERR]

Upper limit value malfunction of front door satellite sensor RH

B0098–25

[SELF-DIAG ERR]

Diagnosis malfunction of front door satellite sensor RH

B0098–28

[OFFSET ERR]

Offset malfunction of front door satellite sensor RH

B0098–81

[COMM ERR]

Communication malfunction of front door satellite sensor RH

B0098–86

[UNMATCH]

Front door satellite sensor RH is out of the specified specification

B0098–88

[OPEN]

Front door satellite sensor RH circuit is open

B0098–93

[RESET]

Reset malfunction of front door satellite sensor RH

SRC-80

< DTC/CIRCUIT DIAGNOSIS >

B0098 FRONT DOOR SATELLITE SENSOR RH

Is the DTC detected?

YES (Current DTC)>>Refer to 

SRC-80, "Diagnosis Procedure"

.

YES (Past DTC)>>GO TO 2.

NO

>> Inspection End.

2.

ERASE SELF-DIAG RESULT

Erase the DTC using CONSULT.
Can the DTC be erased?

YES

>> Inspection End.

NO

>> Refer to 

SRC-80, "Diagnosis Procedure"

.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

1.

CHECK SELF-DIAG RESULT

1. Turn ignition switch ON.

2. Check the air bag warning lamp status. Refer to 

SRC-11, "On Board Diagnosis Function"

.

NOTE:

SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is the DTC detected?

YES

>> Refer to 

SRC-80, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000010877003

NOTE:

Follow the procedures in numerical order when repairing malfunctioning parts. Confirm whether malfunction is

eliminated using air bag warning lamp each time repair is finished. If malfunction is still observed, proceed to

the next step. When malfunction is eliminated, further repair work is not required.

1.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

• Visible damage to connector or terminal

• Loose terminal

• Poor connection

NOTE:

All harness connectors should be inspected from the air bag diagnosis unit to the end component (including

any in-line connectors).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Perform one of the following repairs:

• Visible damage: Replace the harness.

• Loose terminal: Secure the terminal.

• Poor connection: Secure the connection.

2.

CONFIRM DTC

1. Reconnect all harness connectors.

2. Turn ignition switch ON.

3. Check for DTC using CONSULT.
Is DTC still current?

YES

>> GO TO 3

NO

>> Refer to 

GI-53, "Intermittent Incident"

.

3.

WIRING HARNESS

Check the wiring harness for visible damage.

NOTE:

The entire wiring harness should be inspected from the air bag diagnosis sensor unit to the end component

(including any in-line connectors).
Is the inspection result normal?