Nissan Xterra. Manual - part 570

AXLE BEARING

RAX-13

< UNIT REMOVAL AND INSTALLATION >

[C200]

C

E

F

G

H

I

J

K

L

M

A

B

RAX

N

O

P

AXLE BEARING

Removal and Installation

INFOID:0000000009484505

The axle bearing must be replaced every time the axle shaft is removed and installed. Refer to 

RAX-8,

"Removal and Installation"

.

CAUTION:

Do not reuse the axle bearing. 

RAX-14

< UNIT REMOVAL AND INSTALLATION >

[C200]

AXLE OIL SEAL

AXLE OIL SEAL

Removal and Installation

INFOID:0000000009484506

The axle oil seal must be replaced every time the axle shaft is removed and installed. Refer to 

RAX-8,

"Removal and Installation"

.

CAUTION:

Do not reuse the axle oil seal. 

SERVICE DATA AND SPECIFICATIONS (SDS)

RAX-15

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[C200]

C

E

F

G

H

I

J

K

L

M

A

B

RAX

N

O

P

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Axle Specification

INFOID:0000000009484507

Unit: mm (in)

Shim Washers

INFOID:0000000009484508

Unit: mm (in)

*: Always check with the Parts Department for the latest parts information.

Axial end play

0 - 0.07 (0 - 0.003)

Snap ring to shim washer clearance

0.2 (0.008) or less

Snap ring outer diameter installed

47.5 (1.87) maximum

Total end play

0.02 - 0.15 (0.0008 - 0.0059)

Available shim washers

ID Paint Dot Color

Thickness

Part Number*

Pink

2.5 (0.098)

43086-EB08C

Black

2.4 (0.094)

43086-EB07C

Purple

2.3 (0.091)

43086-EB06C

Yellow

2.2 (0.087)

43086-EB05C

Green

2.1 (0.083)

43086-EB04C

Red

2.0 (0.079)

43086-EB03C

White

1.9 (0.075)

43086-EB02C

Blue

1.8 (0.071)

43086-EB01C

RAX-16

< PRECAUTION >

[M226]

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000010202791

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Man-

ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery and wait at least three minutes before performing any service.

Precaution

INFOID:0000000009484510

When installing rubber parts, final tightening must be carried out under unladen condition* with tires

on ground.

* Fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools and mats in designated posi-

tions.