Nissan Pathfinder. Manual - part 370

DLK-246

< SYMPTOM DIAGNOSIS >

HAZARD AND HORN REMINDER DOES NOT OPERATE

HAZARD AND HORN REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009175821

1.

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.

3. Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.

2.

CHECK “HORN WITH KEYLESS LOCK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “HORN WITH KEYLESS LOCK” in “WORK SUPPORT” mode.

3. Check the “HORN WITH KEYLESS LOCK” in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set the “On” in “HORN WITH KEYLESS LOCK”.

3.

CHECK HAZARD FUNCTION

Check hazard function.

Refer to 

DLK-206, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK HORN FUNCTION

Check horn function.

Refer to 

SEC-135, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

REPLACE BCM

• Replace BCM. Refer to 

BCS-80, "Removal and Installation"

.

• Confirm the operation after replacement. 
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

DLK-247

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009175822

1.

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.

3. Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

 .

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.

2.

CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.

3. Check the “ANS BACK I-KEY LOCK”setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set the “Horn Chirp” or “Buzzer” in “ANS BACK I-KEY LOCK”.

3.

CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.

3. Check the “ANS BACK I-KEY UNLOCK” setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set the “On” in “ANS BACK I-KEY UNLOCK”.

4.

CHECK HAZARD FUNCTION

Check hazard function.

Refer to 

DLK-206, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.

Refer to 

DLK-201, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

• Replace BCM. Refer to 

BCS-80, "Removal and Installation"

.

• Confirm the operation after replacement. 
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

DLK-248

< SYMPTOM DIAGNOSIS >

KEY REMINDER FUNCTION DOES NOT OPERATE

KEY REMINDER FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009175823

1.

CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT” mode.

3. Check “ANTI KEY LOCK IN FUNCTI” setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “On” in “ANTI KEY LOCK IN FUNCTI”.

2.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.

• Instrument center: Refer to 

DLK-149, "DTC Logic"

.

• Console: Refer to 

DLK-151, "DTC Logic"

.

• Luggage room: Refer to 

DLK-153, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK UNLOCK SENSOR

Check unlock sensor.

Refer to 

DLK-189, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

REPLACE BCM

• Replace BCM. Refer to 

BCS-80, "Removal and Installation"

.

• Confirm the operation after replacement. 
Is the result normal?

YES

>> Inspection End.

NO

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

WELCOME LIGHT FUNCTION DOES NOT OPERATE

DLK-249

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

WELCOME LIGHT FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009175824

1.

CHECK “WELCOME LIGHT OP SET” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “WELCOME LIGHT OP SET” in “WORK SUPPORT” mode.

3. Check “WELCOME LIGHT OP SET” setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “On” and “WELCOME LIGHT SELECT” in “WORK SUPPORT”.

2.

CHECK “WELCOME LIGHT SELECT” SETTING IN “WORK SUPPORT”

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “WELCOME LIGHT SELECT” in “WORK SUPPORT” mode.

3. Check “WELCOME LIGHT SELECT” setting in “WORK SUPPORT”.

Refer to 

BCS-21, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “WELCOME LIGHT SELECT” setting in “WORK SUPPORT”.

3.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.

• Instrument center: Refer to 

DLK-149, "DTC Logic"

.

• Console: Refer to 

DLK-151, "DTC Logic"

.

• Luggage room: Refer to 

DLK-153, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK OUTSIDE KEY ANTENNA

Check outside key antenna.

• Driver side: Refer to 

DLK-166, "Component Function Check"

.

• Passenger side: Refer to 

DLK-164, "Component Function Check"

.

• Back door: Refer to 

DLK-168, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function
Does door lock/unlock with Intelligent Key button?

YES

>> GO TO 6.

NO

>> Refer to 

DLK-238, "Diagnosis Procedure"

.

6.

CHECK INTERIOR ROOM LAMP CONTROL SYSTEM

Check interior room lamp control system. Refer to 

INL-6, "INTERIOR ROOM LAMP CONTROL SYSTEM :

System Description"

.

Does the room lamp and puddle lamp turn ON?

YES

>> GO TO 7.

NO

>> Refer to 

INL-57, "Symptom Table"

.

7.

REPLACE BCM

• Replace BCM. Refer to 

BCS-80, "Removal and Installation"

.

• Confirm the operation after replacement.
Is the result normal?