Nissan Pathfinder. Manual - part 33

ADP-124

< DTC/CIRCUIT DIAGNOSIS >

LIFTING SENSOR (FRONT)

4. Check continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

 CHECK LIFTING SENSOR (FRONT) POWER SUPPLY

1. Connect driver seat control unit.

2. Turn ignition switch ON.

3. Check voltage between lifting motor LH (front) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

 CHECK LIFTING SENSOR (FRONT) POWER SUPPLY CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect driver seat control unit.

3. Check continuity between driver seat control unit harness connector and lifting motor LH (front) harness

connector.

4. Check continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace driver seat control unit. Refer to 

ADP-161, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

 CHECK LIFTING SENSOR (FRONT) GROUND 

1. Turn ignition switch OFF.

2. Check continuity between lifting motor LH (front) harness connector and ground.

Driver seat control unit

Lifting motor LH (front)

Continuity

Connector

Terminal

Connector

Terminal

B209

30

B218

1

Yes

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B209

30

No

(+)

(–)

Voltage (V)

(Approx.)

Lifting motor LH (front)

Connector

Terminals

B218

3

Ground

Battery voltage

Driver seat control unit

Lifting motor LH (front)

Continuity

Connector

Terminal

Connector

Terminal

B209

5

B218

3

Yes

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B209

5

No

Lifting motor LH (front)

Ground

Continuity

Connector

Terminal

B218

2

Yes

LIFTING SENSOR (FRONT)

ADP-125

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

Is the inspection result normal?

YES

>> Replace lifting motor LH (front). Refer to 

SE-86, "Removal and Installation"

.

NO

>> Repair or replace harness.

ADP-126

< DTC/CIRCUIT DIAGNOSIS >

LIFTING SENSOR (REAR)

LIFTING SENSOR (REAR)

Description

INFOID:0000000009176629

• The lifting sensor (rear) is installed to the seat frame. 

• The pulse signal is input to the driver seat control unit when the lifting (rear) is operated.

• The driver seat control unit counts the pulse and calculates the lifting (rear) amount of the seat. 

Component Function Check

INFOID:0000000009176630

1.

 CHECK FUNCTION

1. Select “LIFT RR PULSE” in “ mode with CONSULT.

2. Check lifting sensor (rear) signal under the following conditions.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Perform diagnosis procedure. Refer to 

ADP-126, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009176631

Regarding Wiring Diagram information, refer to 

ADP-55, "WITH AROUND VIEW MONITOR : Wiring Diagram"

or 

ADP-40, "WITHOUT AROUND VIEW MONITOR : Wiring Diagram"

.

1.

 CHECK LIFTING SENSOR (REAR) SIGNAL

1. Turn ignition switch ON.

2. Read voltage signal between driver seat control unit harness connector and ground with oscilloscope.

Is the inspection result normal?

YES

>> Replace driver seat control unit. Refer to 

ADP-161, "Removal and Installation"

.

NO

>> GO TO 2.

2.

 CHECK LIFTING SENSOR (REAR) CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect driver seat control unit and lifting motor LH (rear).

Monitor item

Condition

Value

LIFT RR PULSE

Seat lifting (rear)

Operate (up)

Change (decrease)

Operate (down)

Change (increase)

Release

No change

(+)

(–)

Condition

Voltage signal

Driver seat control 

unit

Connec-

tor

Termi-

nal

B209

29

Ground

Seat 
lifting
(rear)

Oper-
ate

Other 
than 
above

0 or 5

JMJIA0119ZZ

LIFTING SENSOR (REAR)

ADP-127

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

3. Check the continuity between driver seat control unit harness connector and lifting motor LH (rear) har-

ness connector.

4. Check the continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

 CHECK LIFTING SENSOR (REAR) POWER SUPPLY

1. Connect driver seat control unit.

2. Turn ignition switch ON.

3. Check the voltage between lifting motor LH (rear) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

 CHECK LIFTING SENSOR (REAR) POWER SUPPLY CIRCUIT 

1. Turn ignition switch OFF.

2. Disconnect driver seat control unit.

3. Check the continuity between driver seat control unit harness connector and lifting motor LH (rear) har-

ness connector.

4. Check the continuity between driver seat control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace driver seat control unit. Refer to 

ADP-161, "Removal and Installation"

.

NO

>> Repair or replace harness.

5.

 CHECK LIFTING SENSOR (REAR) GROUND 

1. Turn ignition switch OFF.

2. Check the continuity between lifting motor LH (rear) harness connector and ground.

Driver seat control unit

Lifting motor LH (rear)

Continuity

Connector

Terminal

Connector

Terminal

B209

29

B207

1

Yes

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B209

29

No

(+)

(–)

Voltage (V)

(Approx.)

Lifting motor LH (rear)

Connector

Terminals

B207

3

Ground

Battery voltage

Driver seat control unit

Lifting motor LH (rear)

Continuity

Connector

Terminal

Connector

Terminal

B209

5

B207

3

Yes

Driver seat control unit

Ground

Continuity 

Connector

Terminal

B209

5

No