Nissan Murano Z51. Manual - part 635

EM-12

< PRECAUTION >

PRECAUTIONS

• As for bolt holes, normally apply liquid gasket inside the holes.

Occasionally, it should be applied outside the holes. Check to
read the text of this manual.

• Within 5 minutes of liquid gasket application, install the mating

component.

• If liquid gasket protrudes, wipe it off immediately.
• Never retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill

engine oil and engine coolant.

CAUTION:

If there are specific instructions in this manual, observe
them.

SEM159F

PREPARATION

EM-13

< PREPARATION >

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000005515912

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

KV10116200
(J-26336-A)
Valve spring compressor
1. KV10115900
(J-26336-20)
Attachment
2. KV10109220
(

—

)

Adapter

Disassembling valve mechanism
Part (1) is a component of KV10116200 (J-
26336-A), but Part (2) is not so.

KV10107902
(J-38959)
Valve oil seal puller

Replacing valve oil seal

KV10115600
(J-38958)
Valve oil seal drift

Installing valve oil seal
Use side A.
a: 20 mm (0.79 in) dia.
b: 13 mm (0.51 in) dia.
c: 10.3 mm (0.406 in) dia.
d: 8 mm (0.31 in) dia.
e: 10.7 mm (0.421 in)
f: 5 mm (0.20 in)

EM03470000
(J-8037)
Piston ring compressor

Installing piston assembly into cylinder bore

ST16610001
(J-23907)
Pilot bushing puller

Removing pilot converter

KV10111100
(J-37228)
Seal cutter

Removing oil pan (lower and upper), front and 
rear timing chain case, etc.

PBIC1650E

NT011

S-NT603

NT044

NT045

NT046

EM-14

< PREPARATION >

PREPARATION

Commercial Service Tool

INFOID:0000000005515913

KV10112100
(BT8653-A)
Angle wrench

Tightening bolts for connecting rod bearing 
cap, cylinder head, etc. in angle

KV10117100
(J-3647-A)
Heated oxygen sensor wrench

Loosening or tightening air fuel ratio sensor 1
For 22 mm (0.87 in) width hexagon nut

KV10114400
(J-38365)
Heated oxygen sensor wrench

Loosening or tightening heated oxygen sen-
sor 2
a: 22 mm (0.87 in)

Tool number
(Kent-Moore No.)
Tool name

Description

NT014

NT379

NT636

(Kent-Moore No.)
Tool name

Description

(J-45488)
Quick connector release

Removing fuel tube quick connectors in en-
gine room

(

—

)

Power tool

Loosening bolts and nuts

(

—

)

Tube presser

Pressing the tube of liquid gasket

PBIC0198E

PBIC0190E

NT052

PREPARATION

EM-15

< PREPARATION >

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

(

—

)

Manual lift table caddy

Removing and installing engine 

(J-24239-01)
Cylinder head bolt wrench

Loosening and tightening cylinder head bolt, 
and used with the angle wrench [SST: 
KV10112100 (BT8653-A)]
a: 13 mm (0.51 in) dia.
b: 12 mm (0.47 in)
c: 10 mm (0.39 in)

(

—

)

1. Compression tester
2. Adapter

Checking compression pressure

(

—

)

Spark plug wrench

Removing and installing spark plug
a: 14 mm (0.55 in)

(

—

)

Pulley holder

Removing and installing crankshaft pulley

(

—

)

Valve seat cutter set

Finishing valve seat dimensions

(

—

)

Piston ring expander

Removing and installing piston ring

(Kent-Moore No.)
Tool name

Description

ZZA1210D

NT583

ZZA0008D

JPBIA0399ZZ

ZZA1010D

NT048

NT030