Nissan Murano Z51. Manual - part 1560

WW-118

< SYMPTOM DIAGNOSIS >

WIPER AND WASHER SYSTEM SYMPTOMS

Rear wiper does not 
stop.

ON only

• Combination switch
• BCM

Rear wiper motor circuit
Refer to 

WW-38, "Compo-

nent Function Check"

.

INT only

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom 

Table"

.

Rear wiper does not 
operate normally.

Wiper is not linked to 
the washer operation.

• Combination switch
• Harness between rear wiper motor and BCM
• BCM

Combination switch
Refer to 

BCS-92, "Symptom 

Table"

.

BCM

—

Rear wiper does not 
return to the stop posi-
tion. [Stops after a five-
second operation. 
(Fail-safe)]

• BCM
• Harness between rear wiper motor and BCM
• Rear wiper motor

Rear wiper auto stop signal 
circuit
Refer to 

WW-40, "Compo-

nent Function Check"

.

Symptom

Probable malfunction location

Inspection item

NORMAL OPERATING CONDITION

WW-119

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

NORMAL OPERATING CONDITION

Description

INFOID:0000000005516042

FRONT WIPER MOTOR PROTECTION FUNCTION

• IPDM E/R may stop the front wiper to protect the front wiper motor if any obstruction (operation resistance)

such as a large amount of snow is detected during the front wiper operation.

• At that time turn OFF the front wiper and remove the foreign object. Then wait for approximately 20 seconds

or more and reactivate the front wiper. The wiper will operate normally.

REAR WIPER MOTOR PROTECTION FUNCTION

• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or

more due to a snowfall.

• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.

WW-120

< SYMPTOM DIAGNOSIS >

FRONT WIPER DOES NOT OPERATE

FRONT WIPER DOES NOT OPERATE

Description

INFOID:0000000005516043

The front wiper does not operate under any operation conditions.

Diagnosis Procedure

INFOID:0000000005516044

1.

CHECK WIPER RELAY OPERATION

IPDM E/R AUTO ACTIVE TEST

1.

Start IPDM E/R auto active test. Refer to 

PCS-10, "Diagnosis Description"

.

2.

Check that the front wiper operates at the LO/HI operation.

CONSULT-III ACTIVE TEST

1.

Select “FRONT WIPER” of IPDM E/R active test item.

2.

With operating the test item, check front wiper operation.

Is front wiper operation normally?

YES

>> GO TO 5.

NO

>> GO TO 2.

2.

CHECK FRONT WIPER MOTOR FUSE

1.

Turn the ignition switch OFF.

2.

Check that the front wiper motor 30 A fuse (#60) is not fusing.

Is the fuse fusing?

YES

>> Replace the fuse after repairing the applicable circuit.

NO

>> GO TO 3.

3.

CHECK FRONT WIPER MOTOR GROUND OPEN CIRCUIT 

1.

Disconnect front wiper motor connector.

2.

Check continuity between front wiper motor harness connector and ground.

Does continuity exist?

YES

>> GO TO 4.

NO

>> Repair the harness or connector.

4.

CHECK FRONT WIPER MOTOR OUTPUT VOLTAGE

CONSULT-III ACTIVE TEST

1.

Turn the ignition switch ON.

2.

Select “FRONT WIPER” of IPDM E/R active test item.

3.

With operating the test item, check voltage between IPDM E/R harness connector and ground.

Lo

: Front wiper LO operation

Hi

: Front wiper HI operation

Off

: Stop the front wiper.

Front wiper motor

Ground

Continuity

Connector

Terminal

E12

2

Existed

FRONT WIPER DOES NOT OPERATE

WW-121

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

Is the measurement value normal?

YES

>> Replace front wiper motor.

NO

>> Replace IPDM E/R. 

5.

CHECK FRONT WIPER REQUEST SIGNAL INPUT

CONSULT-III DATA MONITOR

1.

Select “FR WIP REQ” of IPDM E/R data monitor item.

2.

Switch the front wiper switch to HI and LO.

3.

With operating the front wiper switch, check the status of “FR WIP REQ”.

Is the status of item normal?

YES

>> Replace IPDM E/R.

NO

>> GO TO 6.

6.

CHECK COMBINATION SWITCH

Perform the inspection of the combination switch. Refer to 

BCS-92, "Symptom Table"

.

Is combination switch normal?

YES

>> Replace BCM. Refer to 

BCS-95, "Exploded View"

.

NO

>> Repair or replace the applicable parts.

Terminals

Test item

Voltage (Approx.)

(+)

(

−

)

IPDM E/R

Ground

FRONT WIPER

Connector

Terminal

E10

4

Lo

Battery voltage

Off

0 V

5

Hi

Battery voltage

Off

0 V

Monitor item

Condition

Monitor status

FR WIP REQ

Front wiper switch HI

On

Hi

Off

Stop

Front wiper switch LO

On

Low

Off

Stop