Murano Cross Cabriolet Z51 (2012 year). Manual - part 111

WW-36

< REMOVAL AND INSTALLATION >

WASHER NOZZLE & TUBE

WASHER NOZZLE & TUBE

Exploded View

INFOID:0000000007566640

Hydraulic Layout

INFOID:0000000007566641

WASHER NOZZLE

WASHER NOZZLE : Removal and Installation

INFOID:0000000007566642

REMOVAL

1.

Remove cowl top cover. Refer to 

EXT-20, "Removal and Installation"

.

2.

Disconnect front washer tube from front washer nozzle.

1.

Front washer nozzle

2.

Check valve

3.

Front washer tube

JPLIA0869ZZ

1.

Front washer nozzle

2.

Check valve

3.

Front washer tube

4.

Washer tank

: Clip

JPLIA0870ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

WASHER NOZZLE & TUBE

WW-37

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

3.

While pressing pawl (A) on the cowl top cover front side of front
washer nozzle (1), remove front washer nozzle from cowl top
cover.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:

The spray positions differ, check that left and right nozzles are installed correctly.

WASHER NOZZLE : Inspection and Adjustment

INFOID:0000000007566643

INSPECTION

Check valve Inspection

Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.

ADJUSTMENT

Washer Nozzle Spray Position Adjustment

Adjust spray positions to match the positions shown in the figure.

JPLIA0871ZZ

JPLIA0685ZZ

1.

Black printed frame line

: Spray area

: Target spray position

JPLIA0872ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

WW-38

< REMOVAL AND INSTALLATION >

WASHER NOZZLE & TUBE

Unit: mm (in)

Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.

WASHER TUBE

WASHER TUBE : Removal and Installation

INFOID:0000000007566644

REMOVAL

1.

Fully open hood.

2.

Remove washer tube from the washer pump. Refer to 

WW-34, "Removal and Installation"

.

3.

Remove front washer tube from the front washer nozzle. Refer to 

WW-36, "WASHER NOZZLE : Removal

and Installation"

.

4.

Remove front washer tube mounting clip (A). Remove front
washer tube (1) from the vehicle.

INSTALLATION

Install in the reverse order of removal.

Spray position

H

L 

X

Y

S

A

285 (11.22)

429 (16.89)

80 (3.15)

130 (5.12)

65 (2.56)

B

398 (15.67)

232 (9.13)

80 (3.15)

130 (5.12)

65 (2.56)

C

185 (7.28)

69 (2.72)

80 (3.15)

130 (5.12)

65 (2.56)

D

381 (15.00)

37 (1.46)

80 (3.15)

130 (5.12)

65 (2.56)

E

398 (15.67)

232 (9.13)

80 (3.15)

130 (5.12)

65 (2.56)

F

296 (11.65)

421 (16.57)

80 (3.15)

130 (5.12)

65 (2.56)

JPLIA0873ZZ

: Vehicle front

JMLIA2256ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

FRONT WIPER ARM

WW-39

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

FRONT WIPER ARM

Exploded View

INFOID:0000000007566645

Removal and Installation

INFOID:0000000007566646

REMOVAL

1.

Operate the front wiper to move it to the auto stop position.

2.

Fully open hood.

3.

Remove front wiper arm caps.

4.

Remove the front wiper arm mounting nuts.

5.

Raise front wiper arm, and remove front wiper arm from the vehicle.

INSTALLATION

1.

Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.

2.

Operate the front wiper motor to move the front wiper to the auto stop position.

3.

Adjust the front wiper blade position. Refer to 

WW-40, "Adjustment"

.

4.

Install the front wiper arms by tightening the mounting nuts.

5.

Inject the washer fluid.

6.

Operate the front wiper to move it to the auto stop position.

7.

Check that the front wiper blades stop at the specified position.

1.

Front wiper blade RH

2.

Front wiper arm RH

3.

Front wiper arm cap

4.

Front wiper arm LH

5.

Front wiper blade LH

Refer to 

GI-4, "Components"

 for symbols in the figure.

JPLIA0874GB

ELH0717D

Revision: 2013 February

2012 Murano CrossCabriolet

WW-40

< REMOVAL AND INSTALLATION >

FRONT WIPER ARM

8.

Install front wiper arm caps.

Adjustment

INFOID:0000000007566647

WIPER BLADE POSITION ADJUSTMENT

Clearance between the end of cowl top cover and the top of front wiper blade center

Standard clearance

R

: 51.0

±

7.5 mm (2.008 

±

 0.295 in)

L

: 48.0

±

7.5 mm (1.890 

±

 0.295 in)

JPLIA0082ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

WIPER BLADE

WW-41

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

WIPER BLADE

Exploded View

INFOID:0000000007566648

Removal and Installation

INFOID:0000000007566649

REMOVAL

1.

Lift up wiper arm, and set to the position where wiper arm can be locked back.

2.

Press and hold lever (A) of wiper blade (1). Pull in the direction
indicated by the arrow as shown in the figure, and remove wiper
blade from wiper arm (2).

CAUTION:

Wrap wiper arm using a shop cloth so that wiper blade does
not damage windshield glass.

INSTALLATION

Installation is the reverse order of removal.

Replacement

INFOID:0000000007566650

1.

Remove wiper blade from the wiper arm.

1.

Wiper refill

2.

Wiper blade

3.

Wiper arm

A.

Wiper blade tip

B.

Wiper blade end

JMLIA2253ZZ

JMLIA2255ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

WW-42

< REMOVAL AND INSTALLATION >

WIPER BLADE

2.

From portion (A) of wiper refill (1), disengage wiper blade portion
(B) and remove wiper refill in the direction indicated by the arrow
as shown in the figure.

NOTE:

When the vertebra is detached.

• Insert the vertebra (1) into the wiper blade to the same bending

direction.

• If a vertebra has a notch, fit it to a protrusion inside the wiper refill.

JMLIA2254ZZ

JPLIA1586ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

FRONT WIPER DRIVE ASSEMBLY

WW-43

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

FRONT WIPER DRIVE ASSEMBLY

Exploded View

INFOID:0000000007566651

REMOVAL VIEW

DISASSEMBLY VIEW

Removal and Installation

INFOID:0000000007566652

REMOVAL

1.

Remove front wiper arm. Refer to 

WW-39, "Removal and Installation"

.

2.

Remove cowl top cover. Refer to 

EXT-20, "Removal and Installation"

.

3.

Remove bolts from the front wiper drive assembly.

1.

Front wiper drive assembly

JPLIA0875ZZ

1.

Front wiper motor

2.

Shaft seal

3.

Front wiper linkage 2

4.

Front wiper frame

5.

Bracket

6.

Front wiper linkage 1

: Multi

−

purpose grease or an equivalent

JPLIA0876ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

WW-44

< REMOVAL AND INSTALLATION >

FRONT WIPER DRIVE ASSEMBLY

4.

Disconnect the front wiper motor connector.

5.

Remove front wiper drive assembly from the vehicle.

INSTALLATION

1.

Install the front wiper drive assembly to the vehicle.

2.

Connect the front wiper motor connector.

3.

Operate the front wiper to move it to the auto stop position.

4.

Install the cowl top cover. Refer to 

EXT-20, "Removal and Installation"

.

5.

Install front wiper arms. Refer to 

WW-39, "Removal and Installation"

.

Disassembly and Assembly

INFOID:0000000007566653

DISASSEMBLY

1.

Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.

CAUTION:

Never bend the linkage or damage the plastic part of the ball joint when removing the front wiper
linkage.

2.

Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.

ASSEMBLY

1.

Connect the front wiper motor connector.

2.

Operate the front wiper to move it to the auto stop position.

3.

Disconnect the front wiper motor connector.

4.

Install front wiper motor to front wiper frame.

5.

Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.

6.

Install the front wiper linkage 1 to the front wiper frame.

CAUTION:

• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint

(retainer). Apply multi

−

purpose grease or an equivalent if necessary.

Revision: 2013 February

2012 Murano CrossCabriolet

WIPER AND WASHER SWITCH

WW-45

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

WW

N

O

P

WIPER AND WASHER SWITCH

Exploded View

INFOID:0000000007566654

Refer to 

BCS-77, "Exploded View"

.

Revision: 2013 February

2012 Murano CrossCabriolet