Murano Cross Cabriolet Z51 (2012 year). Manual

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

WT-21

< DTC/CIRCUIT DIAGNOSIS >

DTC/CIRCUIT DIAGNOSIS

C1704, C1705, C1706, C1707 LOW TIRE PRESSURE

Description

INFOID:0000000007565882

When the tire pressure monitoring system detects low inflation pressure, the low tire pressure warning lamps
in the combination meter comes on.

DTC Logic

INFOID:0000000007565883

DTC DETECTION LOGIC

NOTE:

182.7 kPa (1.9 kg/cm

, 26 psi): Standard air pressure is for 230 kPa (2.3 kg/cm

,33 psi) vehicles.

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check the tire pressure for all wheels and adjust to the specified value. Refer to

WT-49, "Tire Air Pres-

sure"

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1704”, “C1705”, “C1706”, “C1707” detected?

YES

>> Perform trouble diagnosis. Refer to

WT-21, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007565884

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to

WT-49, "Tire Air Pressure"

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to

WT-46, "Exploded View"

>> After adjusting the air pressure, GO TO 2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

DTC

Display item

Malfunction detected condition

Possible cause

C1704

LOW PRESSURE FL

Front LH tire pressure drops to * kPa (* kg/cm

, * psi) or less. [NOTE]

• Low tire pressure
• Tire pressure sen-

sor malfunction

C1705

LOW PRESSURE FR

Front RH tire pressure drops to * kPa (* kg/cm

, * psi) or less. [NOTE]

C1706

LOW PRESSURE RR

Rear RH tire pressure drops to * kPa (* kg/cm

, * psi) or less. [NOTE]

C1707

LOW PRESSURE RL

Rear LH tire pressure drops to * kPa (* kg/cm

, * psi) or less. [NOTE]

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2013 February

2012 Murano CrossCabriolet

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

WT-23

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000007565885

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1708”, “C1709”, “C1710”, “C1711” detected?

YES

>> Perform trouble diagnosis. Refer to

WT-23, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007565886

CHECK TIRE PRESSURE SIGNAL

With CONSULT

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.

Is a tire pressure of 0 kPa (0 Psi) displayed for all wheels?

YES

>> GO TO 2.

>> GO TO 5.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

Turn the ignition switch OFF.

Disconnect BCM harness connector and tire pressure receiver harness connector.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

DTC

Display item

Malfunction detected condition

Possible cause

C1708

[NO DATA] FL

Tire pressure data signal from the front left wheel tire
pressure sensor cannot be detected.

• Harness or connector

(Tire pressure receiver, BCM)

• ID registration is not finished
• Tire pressure sensor malfunction
• BCM malfunction

C1709

[NO DATA] FR

Tire pressure data signal from the front right wheel tire
pressure sensor cannot be detected.

C1710

[NO DATA] RR

Tire pressure data signal from the rear right wheel tire
pressure sensor cannot be detected.

C1711

[NO DATA] RL

Tire pressure data signal from the rear left wheel tire
pressure sensor cannot be detected.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2013 February

2012 Murano CrossCabriolet

WT-24

< DTC/CIRCUIT DIAGNOSIS >

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace damaged parts.

CHECK TIRE PRESSURE RECEIVER POWER SUPPLY CIRCUIT

Connect the BCM harness connector.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check the voltage between the BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace damaged parts.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to

WT-30, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 5.

>> Replace tire pressure receiver. Refer to

WT-48, "Removal and Installation"

CHECK ID REGISTRATION

Perform ID registration of all tire pressure sensors. Refer to

WT-19, "Work Procedure"

Can ID registration of all tire pressure sensors be completed?

YES

>> GO TO 6.

>> Replace tire pressure sensor. Refer to

WT-46, "Exploded View"

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

138

139

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

BCM

—

Voltage

(Approx.)

Connector

Terminal

M123

138

Ground

5 V

Revision: 2013 February

2012 Murano CrossCabriolet

C1708, C1709, C1710, C1711 TIRE PRESSURE SENSOR

WT-25

< DTC/CIRCUIT DIAGNOSIS >

CAUTION:

Stop the vehicle and within 15 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of
“BCM” to read the tire pressure for all wheels.
Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to

WT-46, "Exploded View"

>> Replace BCM. Refer to

BCS-76, "Removal and Installation"

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive at a speed of 40 km/h (25 MPH) or more, for several
minutes without stopping.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2013 February

2012 Murano CrossCabriolet

WT-26

< DTC/CIRCUIT DIAGNOSIS >

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

C1716, C1717, C1718, C1719 TIRE PRESSURE SENSOR

DTC Logic

INFOID:0000000007565887

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check the tire pressure for all wheels and adjust to the specified value. Refer to

WT-49, "Tire Air Pres-

sure"

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1716”, “C1717”, “C1718”, “C1719” detected?

YES

>> Perform trouble diagnosis. Refer to

WT-26, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007565888

CHECK TIRE PRESSURE

Check the internal pressure of all wheels. Refer to

WT-49, "Tire Air Pressure"

Is the inspection result normal?

YES

>> Replace the DTC-detected malfunctioning tire pressure sensor. Refer to

WT-46, "Exploded View"

>> After adjusting the tire pressure, GO TO 2.

CHECK TIRE PRESSURE SIGNAL

With CONSULT

Check and adjust the tire pressure for all wheels. Refer to

WT-49, "Tire Air Pressure"

Perform tire pressure sensor ID registration for all wheels. Refer to

WT-19, "Work Procedure"

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 15 minutes, use CONSULT “DATA MONITOR” to display the tire pres-
sure for all wheels.

Check that “DATA MONITOR” displays tire pressure of 438.60 kPa (4.47 kg/cm

, 63.60 Psi).

Is the inspection 438.60 kPa (4.47 kg/cm

, 63.60 Psi)?

YES

>> Replace tire pressure sensor the tire pressure 438.60 kPa (4.47 kg/cm

, 63.60 Psi) displayed.

Refer to

WT-46, "Exploded View"

>> GO TO 1.

DTC

Display item

Malfunction detected condition

Possible case

C1716

[PRESSDATA ERR] FL

Malfunction in the tire pressure data from the front left
wheel tire pressure sensor.

• ID registration is not fin-

ished

• Tire pressure sensor mal-

function

C1717

[PRESSDATA ERR] FR

Malfunction in the tire pressure data from the front right
wheel tire pressure sensor.

C1718

[PRESSDATA ERR] RR

Malfunction in the tire pressure data from the rear right
wheel tire pressure sensor.

C1719

[PRESSDATA ERR] RL

Malfunction in the tire pressure data from the rear left
wheel tire pressure sensor.

Revision: 2013 February

2012 Murano CrossCabriolet

C1729 VEHICLE SPEED SIGNAL

WT-27

< DTC/CIRCUIT DIAGNOSIS >

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000007565889

BCM detects no vehicle speed signal.

DTC Logic

INFOID:0000000007565890

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT

Drive for several minutes at a speed of 40 km/h (25 MPH) or more, then stop the vehicle.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

Is DTC “C1729” detected?

YES

>> Perform trouble diagnosis. Refer to

WT-27, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007565891

PERFORM COMBINATION METER SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” of “METER/M&A”.

Is any DTC detected?

YES

>> Check the DTC. Refer to

MWI-31, "DTC Index"

>> GO TO 2.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is DTC “C1729” detected?

YES

>> Replace BCM. Refer to

WT-9, "COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)"

>> GO TO 3.

CHECK INFORMATION

With CONSULT

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

Select “BCM” in “DATA MONITOR”, and check the input/output values. Refer to

BCS-31, "Reference

Value"

Is the inspection result normal?

YES

>> Check pin terminal and connection of each harness connector for malfunctioning conditions.

>> Replace BCM. Refer to

BCS-76, "Removal and Installation"

DTC

number

Trouble diagnosis name

DTC detecting condition

Possible case

C1729

VHCL SPEED SIG ERR

Vehicle speed signal not detected.

• CAN communication error
• Combination meter malfunction

Revision: 2013 February

2012 Murano CrossCabriolet

WT-28

< DTC/CIRCUIT DIAGNOSIS >

C1734 BCM

C1734 BCM

DTC Logic

INFOID:0000000007565892

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.

CAUTION:

Perform within 15 minutes after stop the vehicle.

Is DTC “C1734” detected?

YES

>> Perform trouble diagnosis. Refer to

WT-28, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000007565893

CHECK BCM POWER SUPPLY

Turn the ignition switch OFF.

Disconnect BCM harness connector.

Check voltage between BCM harness connector terminals and ground.

Is the power supply normal?

YES

>> GO TO 2.

Check the following. If any items are damaged, repair or replace damage parts.

• 40A fusible link [No. L located in the fuse block]. Refer to

PG-35, "Fuse and Fusible Link

Arrangement"

• 10A fuse [No. 10 located in the fuse block (J/B)]. Refer to

PG-34, "Fuse, Connector and Termi-

nal Arrangement"

• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check the Battery voltage.

CHECK BCM GROUND

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace damaged parts.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

Disconnect tire pressure receiver harness connector.

Check the continuity between BCM harness connector and tire pressure receiver harness connector.

DTC

Display item

Malfunction detected condition

Possible case

C1734

CONTROL UNIT

Tire pressure monitoring system malfunction in BCM

BCM malfunction

BCM

—

Voltage

(Approx.)

Connector

Terminal

M118

Ground

Battery voltage

M119

BCM

—

Continuity

Connector

Terminal

M119

Ground

Existed

Revision: 2013 February

2012 Murano CrossCabriolet

C1734 BCM

WT-29

< DTC/CIRCUIT DIAGNOSIS >

Check the continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace damaged parts.

CHECK BCM

Check the BCM input/output signal. Refer to

BCS-31, "Reference Value"

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 5.

CHECK BCM HARNESS CONNECTOR

Check the BCM pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-76, "Removal and Installation"

>> Check for looseness or damage at the harness connector pins of the BCM. Repair or replace if

necessary.

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

138

139

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Revision: 2013 February

2012 Murano CrossCabriolet

WT-30

< DTC/CIRCUIT DIAGNOSIS >

TIRE PRESSURE RECEIVER

TIRE PRESSURE RECEIVER

Component Function Check

INFOID:0000000007565894

TIRE PRESSURE MONITORING SYSTEM OPERATION

With CONSULT

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.

On “DATA MONITOR”, select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”, and check that the tire pressures match the standard value.

CAUTION:

Stop the vehicle and within 5 minutes, use CONSULT “DATA MONITOR” to display the tire pressure for
all wheels.

Is the inspection result normal?

YES

>> INSPECTION END

>> Perform trouble diagnosis. Refer to

WT-30, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000007565895

CHECK TIRE PRESSURE RECEIVER SIGNAL

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check tire pressure receiver connector and ground signal with oscilloscope.

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 2.

CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE

Turn the ignition switch OFF.

Disconnect tire pressure receiver connector.

Turn the ignition switch ON.

Monitor item

Condition

Displayed value

AIR PRESS FL

Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.

Internal pressure of tires

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Tire pressure receiver

—

Condition

Voltage

(Approx.)

Connector

Terminal

M21

Ground

Stand by state

When receiving the signal from the tire
pressure sensor

OCC3881D

OCC3880D

Revision: 2013 February

2012 Murano CrossCabriolet

TIRE PRESSURE RECEIVER

WT-31

< DTC/CIRCUIT DIAGNOSIS >

CAUTION:

Never start the engine.

Check voltage between tire pressure receiver connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace damaged parts.

CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT

Turn the ignition switch OFF.

Disconnect BCM harness connector.

Check continuity between BCM harness connector and tire pressure receiver connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace damaged parts.

CHECK BCM CIRCUIT

Inspect the BCM circuit. Refer to

WT-28, "Diagnosis Procedure"

Is the BCM circuit normal?

YES

>> Replace tire pressure receiver. Refer to

WT-48, "Removal and Installation"

>> Replace BCM. Refer to

STC-19, "Removal and Installation"

Tire pressure receiver

—

Voltage

(Approx.)

Connector

Terminal

M21

Ground

5.0 V

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

Revision: 2013 February

2012 Murano CrossCabriolet

WT-32

< DTC/CIRCUIT DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP

LOW TIRE PRESSURE WARNING LAMP

Component Function Check

INFOID:0000000007565896

CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP

Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> INSPECTION END

>> Perform trouble diagnosis. Refer to

WT-32, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000007565897

POWER SUPPLY AND GROUND CIRCUIT

Check power supply and ground circuit. Refer to

WT-33, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace damaged parts.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?

YES

>> Check the DTC. Refer to

MWI-31, "DTC Index"

>> GO TO 3.

CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL

With CONSULT

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.

Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.

Is the inspection result normal?

YES

>> Check the combination meter. Refer to

MWI-8, "METER SYSTEM : System Description"

>> Replace the BCM. Refer to

BCS-76, "Removal and Installation"

Revision: 2013 February

2012 Murano CrossCabriolet

POWER SUPPLY AND GROUND CIRCUIT

WT-33

< DTC/CIRCUIT DIAGNOSIS >

POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000007565898

POWER SUPPLY SYSTEM CHECK

Turn the ignition switch OFF.

Disconnect the BCM harness connector.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check the voltage between the BCM harness connector and the ground.

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace damaged parts.

GROUND SYSTEM INSPECTION

Turn the ignition switch OFF.

Check the continuity between the BCM harness connector and the ground.

Is the inspection result normal?

YES

>> • Check the 10A fuse [No. 10 in fuse block (J/B)].

• Check the 40A fusible link [No. L in fuse block].

>> Repair or replace damaged parts.

BCM

—

Voltage

(Approx.)

Connector

Terminal

M118

Ground

Battery voltage

M119

BCM

—

Continuity

Connector

Terminal

M119

Ground

Existed

Revision: 2013 February

2012 Murano CrossCabriolet

TPMS

WT-35

< SYMPTOM DIAGNOSIS >

Diagnosis items

Symptom

(Ignition switch

ON)

Low tire pressure warning lamp

Cause

Action

Low tire pres-
sure warning
lamp

The low tire pres-
sure warning lamp
illuminates for 1
second, then turns
OFF.

Wake-up operation for all
tire pressure sensors at
wheels is completed.

No system malfunctions

The low tire pres-
sure warning lamp
repeats blinking
ON for 2 seconds
and OFF for 0.2
seconds.

Wake-up operation for all
tire pressure sensors at
wheels is not completed.

Perform the wake-up oper-
ation for all tire pressure
sensors at wheels. Refer to

WT-18, "Work Procedure"

The low tire pres-
sure warning lamp
blinks once.

The front left tire pres-
sure sensor is not acti-
vated.

Perform the wake-up oper-
ation for the tire pressure
sensor at front left wheel.
Refer to

WT-18, "Work Pro-

cedure"

The low tire pres-
sure warning lamp
repeats blinking
twice.

The front right tire pres-
sure sensor is not acti-
vated.

Perform the wake-up oper-
ation for the tire pressure
sensor at front right wheel.
Refer to

WT-18, "Work Pro-

cedure"

The low tire pres-
sure warning lamp
repeats blinking for
3 times.

The rear right tire pres-
sure sensor is not acti-
vated.

Perform the wake-up oper-
ation for the tire pressure
sensor at rear right wheel.
Refer to

WT-18, "Work Pro-

cedure"

The low tire pres-
sure warning lamp
repeats blinking for
4 times.

The rear left tire pressure
sensor is not activated.

Perform the wake-up oper-
ation for the tire pressure
sensor at rear left wheel.
Refer to

WT-18, "Work Pro-

cedure"

The low tire pres-
sure warning lamp
turns ON and stays
illuminated.

Low tire pressure

Check the tire pressure for
all wheels and adjust to the
specified value. Refer to

WT-49, "Tire Air Pressure"

SEIA0592E

SEIA0593E

JPEIC0090GB

SEIA0595E

SEIA0596E

SEIA0597E

SEIA0598E

Revision: 2013 February

2012 Murano CrossCabriolet

WT-36

< SYMPTOM DIAGNOSIS >

TPMS

NOTE:
If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-
ble low tire pressure warning lamp blinking patterns are displayed continuously.
(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and
rear right wheel tire pressure sensors.)

Low tire pres-
sure warning
lamp

The low tire pres-
sure warning lamp
repeats blinking at
0.5-second inter-
vals for 1 minute,
and then stays illu-
minated.

The combination meter
fuse is open or removed
(or pulled out).

Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.

The low tire pressure
warning control unit har-
ness connector is re-
moved.

Check the connection con-
ditions of the low tire pres-
sure warning control unit
harness connector, and re-
pair if necessary.

Tire Pressure Monitoring
System (TPMS) mal-
function.

• Perform CONSULT self-

diagnosis. Refer to

WT-

10, "AIR PRESSURE
MONITOR : CONSULT
Function (BCM - AIR
PRESSURE MONI-
TOR)"

• If necessary, perform tire

pressure sensor ID regis-
tration. Refer to

WT-19,

"Work Procedure"

Hazard warning
lamp

The hazard warn-
ing lamp does not
blink twice when
the tire pressure
sensor is activated.

—

The tire pressure
sensor activation
tool (J-45295) does
not activate.

The ignition switch
is OFF when the
tire pressure sen-
sor wake-up opera-
tion is performed.

The tire pressure
sensor activation
tool (J-45295) is
not used in the cor-
rect position.

The tire pressure
sensor is already
waked up.

Replace the battery in
the tire pressure sen-
sor activation tool (J-
45295).

Turn the ignition
switch ON when per-
forming the tire pres-
sure sensor wake-up
operation.

Operate the tire pres-
sure sensor activation
tool (J-45295) in the
correct position when
performing the wake-
up operation.

No procedure.

Diagnosis items

Symptom

(Ignition switch

ON)

Low tire pressure warning lamp

Cause

Action

SEIA0788E

Revision: 2013 February

2012 Murano CrossCabriolet

Murano Cross Cabriolet Z51 (2012 year). Manual - part 107