Murano Cross Cabriolet Z51 (2012 year). Manual - part 33

EXL-52

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

OPTICAL SENSOR

OPTICAL SENSOR

Component Function Check

INFOID:0000000007565451

1.

CHECK OPTICAL SENSOR SIGNAL BY CONSULT

CONSULT DATA MONITOR

1.

Turn ignition switch ON.

2.

Select “OPTICAL SENSOR” of BCM (HEADLAMP) data monitor item.

3.

Turn lighting switch AUTO.

4.

With the optical sensor illuminating, check the monitor status. 

*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.

Is the item status normal?

YES

>> Optical sensor is normal.

NO

>> Refer to 

EXL-52, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000007565452

1.

CHECK OPTICAL SENSOR POWER SUPPLY INPUT

1.

Turn ignition switch ON.

2.

Turn lighting switch AUTO.

3.

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK OPTICAL SENSOR GROUND INPUT

Check voltage between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 6.

3.

CHECK OPTICAL SENSOR SIGNAL OUTPUT

 With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.

Monitor item

Condition

Voltage (Approx.)

OPTICAL SENSOR

Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

(+)

(

−

)

Voltage

(Approx.)

Optical sensor

Connector

Terminal

M17

1

Ground

5 V

terminal

Voltage

(Approx.)

(+)

(

−

)

Optical sensor

Ground

Connector

Terminal

M17

3

0 V

(+)

(

−

)

Condition

Voltage

(Approx.)

Optical sensor

Connector

Terminal

Revision: 2013 February

2012 Murano CrossCabriolet

OPTICAL SENSOR

EXL-53

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Replace optical sensor.

4.

CHECK OPTICAL SENSOR OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect optical sensor connector and BCM connector.

3.

Check continuity between optical sensor harness connector and BCM harness connector.

Does continuity exist?

YES

>> GO TO 5.

NO

>> Repair or replace harness.

5.

CHECK OPTICAL SENSOR SHORT CIRCUIT

Check continuity between optical sensor harness connector and ground.

Does continuity exist?

YES

>> Repair or replace harness.

NO

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

6.

CHECK OPTICAL SENSOR GROUND OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect optical sensor connector and BCM connector.

3.

Check continuity between optical sensor harness connector and BCM harness connector.

Does continuity exist?

YES

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

NO

>> Repair or replace harness.

7.

CHECK OPTICAL SENSOR SIGNAL OPEN CIRCUIT 

1.

Turn ignition switch OFF.

2.

Disconnect optical sensor connector and BCM connector.

3.

Check continuity between optical sensor harness connector and BCM harness connector.

Does continuity exist?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

8.

CHECK OPTICAL SENSOR SHORT CIRCUIT

M17

2

Ground

Optical sensor

When illuminating

3.1 V or more *

When shutting off light

0.6 V or less

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M17

1

M123

138

Existed

Optical sensor

Ground

Continuity

Connector

Terminal

M17

1

Not existed

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M17

3

M123

137

Existed

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M17

2

M123

113

Existed

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-54

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

OPTICAL SENSOR

Check continuity between optical sensor harness connector and ground.

Does continuity exist?

YES

>> Repair or replace harness.

NO

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

Optical sensor

Ground

Continuity

Connector

Terminal

M17

2

Not existed

Revision: 2013 February

2012 Murano CrossCabriolet

HAZARD SWITCH

EXL-55

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HAZARD SWITCH

Component Function Check

INFOID:0000000007565453

1.

CHECK HAZARD SWITCH SIGNAL BY CONSULT

CONSULT DATA MONITOR

1.

Turn ignition switch ON.

2.

Select “HAZARD SW” of BCM (FLASHER) data monitor item.

3.

With operating the hazard switch, check the monitor status.

Is the item status normal?

YES

>> Hazard switch circuit is normal.

NO

>> Refer to 

EXL-55, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000007565454

1.

CHECK HAZARD SWITCH SIGNAL INPUT

1.

Turn ignition switch OFF.

2.

Disconnect hazard switch connector.

3.

Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between hazard switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT

Check continuity between hazard switch harness connector and ground.

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

ON

On

OFF

Off

(+)

(

−

)

Voltage (Approx.)

Hazard switch

Connector

Terminal

M45

2

Ground

12 V

JPMIA0012GB

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M45

2

M122

110

Existed

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-56

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

HAZARD SWITCH

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

NO

>> Repair or replace harness.

4.

CHECK HAZARD SWITCH GROUND OPEN CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch.

NO

>> Repair or replace harness.

Hazard switch

Ground

Continuity

Connector

Terminal

M45

2

Not existed

Hazard switch

Ground

Continuity

Connector

Terminal

M45

1

Existed

Revision: 2013 February

2012 Murano CrossCabriolet

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-57

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000007565455

CAUTION:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagno-
sis if any DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp does not 
switch to the high beam.

One side

• Fuse
• Harness between IPDM E/R 

and high beam solenoid

• Harness between high beam 

solenoid and ground

• Front combination lamp

(High beam solenoid)

• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-37, "Component 

Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM”
Refer to 

EXL-61, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON.
(The headlamp switches to the high beam.)

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEAD LAMP)

Active test “HEADLAMP”

Headlamp does not 
switch to the low beam.

One side

Front combination lamp (High 
beam solenoid)

—

Both sides

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-74, "Symptom Table"

.

High beam request signal
• BCM
• IPDM E/R

IPDM E/R
Data monitor “HL HI REQ”

IPDM E/R

—

Headlamp is not turned 
ON.

One side

• Fuse
• Xenon bulb
• Harness between IPDM E/R 

and headlamp

• Harness between headlamp 

and ground

• Front combination lamp (xenon 

headlamp)

• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-39, "Component 

Function Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-62, "Diagnosis Procedure"

.

Headlamp is not turned ON/OFF with the lighting 
switch AUTO.

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-74, "Symptom Table"

.

• Optical sensor
• Harness between optical sen-

sor and BCM

• BCM

Optical sensor
Refer to 

EXL-52, "Component 

Function Check"

.

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-58

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Front fog lamp is not 
turned ON.

One side

• Front fog lamp bulb
• Harness between IPDM E/R 

and front fog lamp 

• Harness between front fog lamp 

and ground 

• IPDM E/R

Front fog lamp circuit
Refer to 

EXL-50, "Component 

Function Check"

.

Both side

Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to 

EXL-64, "Diagnosis Procedure"

.

Parking lamp is not turned ON.

• Parking lamp bulb
• Harness between IPDM E/R 

and parking lamp

• Harness between parking lamp 

and ground

Parking lamp circuit
Refer to 

EXL-42, "Component 

Function Check"

.

Front side marker lamp is not turned ON.

• Front side marker lamp bulb
• Harness between IPDM E/R 

and front side marker lamp

• Harness between front side 

marker lamp and ground

Front side marker lamp circuit
Refer to 

EXL-44, "Component 

Function Check"

.

Parking lamp and front side marker lamp are not 
turned ON.

• Fuse
• Harness between IPDM E/R 

and parking lamp

• IPDM E/R

Parking lamp circuit
Refer to 

EXL-42, "Component 

Function Check"

.

Tail lamp / Rear side marker lamp is not turned ON.

• Rear side marker lamp bulb
• Rear combination lamp
• Harness between IPDM E/R 

and rear combination lamp

• Harness between rear combi-

nation lamp and ground

Tail lamp circuit
Refer to 

EXL-45, "Component 

Function Check"

.

License plate lamp is not turned ON.

• License plate lamp bulb
• Harness between IPDM E/R 

and license plate lamp

• Harness between license plate 

lamp and ground

License plate lamp circuit
Refer to 

EXL-47, "Component 

Function Check"

.

Tail lamp and license plate lamp are not turned ON.

• Fuse
• Harness between IPDM E/R 

and rear combination lamp

• IPDM E/R

License plate lamp circuit
Refer to 

EXL-47, "Component 

Function Check"

.

Parking lamp, tail lamp, side marker lamp and li-
cense plate lamp are not turned ON.

Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED 
ON”
Refer to 

EXL-63, "Diagnosis Procedure"

.

Turn signal lamp does not 
blink.

Indicator lamp is nor-
mal.
(Applicable side per-
forms high flasher acti-
vation.)

• Turn signal lamp bulb
• Harness between BCM and 

each turn signal lamp

• Harness between each turn sig-

nal lamp and ground

Turn signal lamp circuit
Refer to 

EXL-48, "Component 

Function Check"

.

Indicator lamp is includ-
ed

• Combination switch
• Harness between combination 

switch and BCM

• BCM

Combination switch
Refer to 

BCS-74, "Symptom Table"

.

Symptom

Possible cause

Inspection item

Revision: 2013 February

2012 Murano CrossCabriolet

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-59

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Turn signal indicator lamp 
does not blink.
(Turn signal indicator 
lamp is normal.)

One side

Combination meter

—

Both sides
(Always)

• Turn indicator signal
• Combination meter 
• BCM
• Combination meter

• Combination meter 

Data monitor “TURN IND”

• BCM (FLASHER)

Active test “FLASHER”

Both sides
(Only when activating 
hazard warning lamp 
with ignition switch 
OFF)

• Combination meter power sup-

ply and ground circuit

• Combination meter

Combination meter
Power supply and ground circuit
Refer to 

MWI-47, "COMBINATION 

METER : Diagnosis Procedure"

.

• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)

• Hazard switch
• Harness between hazard 

switch and BCM

• Harness between hazard 

switch and ground

• BCM

Hazard switch
Refer to 

EXL-55, "Component 

Function Check"

.

Symptom

Possible cause

Inspection item

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-60

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

NORMAL OPERATING CONDITION

NORMAL OPERATING CONDITION

Description

INFOID:0000000007565456

XENON HEADLAMP

• Brightness and the color of light may change slightly immediately after turning the headlamp ON until the

xenon bulb becomes stable. This is normal.

• Illumination time lag may occur between right and left. This is normal.

AUTO LIGHT SYSTEM

The headlamp may not be turned ON/OFF immediately after passing dark area or bright area (short tunnel,
sky bridge, shadowed area etc.) while using the auto light system. This causes the control difference. This is
normal.

Revision: 2013 February

2012 Murano CrossCabriolet

BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM

EXL-61

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

BOTH SIDE HEADLAMPS DO NOT SWITCH TO HIGH BEAM

Description

INFOID:0000000007565457

The headlamp (both sides) does not switch to the high beam when setting to the lighting switch HI or PASS.

Diagnosis Procedure

INFOID:0000000007565458

1.

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to 

BCS-74, "Symptom Table"

.

Is the combination switch normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “HL HI REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the item status normal?

YES

>> GO TO 3.

NO

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

3.

HEADLAMP (HI) CIRCUIT INSPECTION

Check the headlamp (HI) circuit. Refer to 

EXL-37, "Component Function Check"

.

Is the headlamp (HI) circuit normal?

YES

>> Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Repair or replace the malfunctioning part.

Monitor item

Condition

Monitor status

HL HI REQ

Lighting switch
(2ND)

HI or PASS

ON

Except for HI or PASS

OFF

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-62

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON

Description

INFOID:0000000007565459

Both side headlamps (LO) are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000007565460

1.

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to 

BCS-74, "Symptom Table"

.

Is the combination switch normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “HL LO REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the item status normal?

YES

>> GO TO 3.

NO

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

3.

HEADLAMP (LO) CIRCUIT INSPECTION

Check the headlamp (LO) circuit. Refer to 

EXL-39, "Component Function Check"

.

Is the headlamp (LO) circuit normal?

YES

>> Replace IPDM E/R.

NO

>> Repair or replace the malfunctioning part.

Monitor item

Condition

Monitor status

HL LO REQ

Lighting switch

2ND

ON

OFF

OFF

Revision: 2013 February

2012 Murano CrossCabriolet

PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON

EXL-63

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON

Description

INFOID:0000000007565461

The parking, license plate, side marker, tail lamps and each illumination are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000007565462

1.

COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to 

BCS-74, "Symptom Table"

.

Is the combination switch normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning part.

2.

CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

2.

With operating the lighting switch, check the monitor status.

Is the item status normal?

YES

>> Replace IPDM E/R.

NO

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

Monitor item

Condition

Monitor status

TAIL & CLR REQ

Lighting switch

1ST

On

OFF

Off

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-64

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON

Description

INFOID:0000000007565463

The front fog lamps are not turned ON in any condition.

Diagnosis Procedure

INFOID:0000000007565464

1.

CHECK FRONT FOG LAMP FUSE

1.

Turn ignition switch OFF.

2.

Check that the following fuse is not fusing.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK FRONT FOG LAMP SHORT CIRCUIT

1.

Disconnect front fog connector and IPDM E/R connector.

2.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)

NO

>> Repair or replace harness. And then replace the fuse.

3.

COMBINATION SWITCH INSPECTION

Check combination switch. Refer to 

BCS-74, "Symptom Table"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning part.

4.

CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT

CONSULT DATA MONITOR

1.

Select “FR FOG REQ” of IPDM E/R data monitor item.

2.

With operating the front fog lamp switch, check the monitor status.

Is the item status normal?

YES

>> GO TO 5.

NO

>> Replace BCM. Refer to 

BCS-76, "Removal and Installation"

.

5.

FRONT FOG LAMP CIRCUIT INSPECTION

Check the front fog lamp circuit. Refer to 

EXL-50, "Component Function Check"

.

Is the inspection result normal?

YES

>> Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Repair or replace the malfunctioning part.

Unit

Location

Fuse No.

Capacity

Front fog lamp

IPDM E/R

#58

15 A

IPDM E/R

Ground

Continuity

Connector

Terminal

RH

E345

86

Not existed

LH

87

Monitor item

Condition

Monitor status

FR FOG REQ

Front fog lamp switch
(With lighting switch 1ST)

ON

On

OFF

Off

Revision: 2013 February

2012 Murano CrossCabriolet

HEADLAMP AIMING ADJUSTMENT

EXL-65

< PERIODIC MAINTENANCE >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

PERIODIC MAINTENANCE

HEADLAMP AIMING ADJUSTMENT

Description

INFOID:0000000007565465

PREPARATION BEFORE ADJUSTING

NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the front combination lamp assembly has

been replaced.

Before performing aiming adjustment, check the following. 

• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-

gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool. 

• Wipe out dirt on the headlamp.

CAUTION:

Never use organic solvent (thinner, gasoline etc.)

• Ride alone on the driver seat.
• Headlamp aiming switch sets to “0”.

AIMING ADJUSTMENT SCREW

JPLIA0810ZZ

A.

Headlamp RH (UP/DOWN) adjust-
ment screw

B.

Headlamp LH (UP/DOWN) adjust-
ment screw

: Vehicle center

Revision: 2013 February

2012 Murano CrossCabriolet

EXL-66

< PERIODIC MAINTENANCE >

[XENON TYPE]

HEADLAMP AIMING ADJUSTMENT

Aiming Adjustment Procedure

INFOID:0000000007565466

1.

Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.

2.

Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp bulb center and the
screen.

3.

Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.

CAUTION:

Never cover the lens surface with a tape etc. The lens is made of resin.

4.

Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).

Low beam distribution on the screen 

5.

Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).

unit: mm (in)

Side view

Adjustment screw

Screw driver rotation

Facing direction

A

Headlamp RH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

UP

B

Headlamp LH (UP/DOWN)

Clockwise

DOWN

Counterclockwise

UP

Light axis measurement range (R)

: 350 

±

 175 mm (13.78 

±

 6.89 in)

JSLIA0005ZZ

Horizontal center line of headlamp (H)

Highest cutoff line height (M)

Lowest cutoff line height (N)

700 (27.56) or less

4 (0.16)

30 (1.18)

701(27.60) – 800 (31.50)

4 (0.16)

30 (1.18)

801 (31.54) or more

17 (0.67)

44 (1.73)

JSLIA0006ZZ

Revision: 2013 February

2012 Murano CrossCabriolet

HEADLAMP AIMING ADJUSTMENT

EXL-67

< PERIODIC MAINTENANCE >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Distance between the headlamp 
center and the screen (L)

: 10 m (32.8 ft)

Revision: 2013 February

2012 Murano CrossCabriolet