Murano Cross Cabriolet Z51 (2011 year). Manual - part 60

STR-16

< REMOVAL AND INSTALLATION >

STARTER MOTOR

Type: M000TA0072

Removal and Installation

INFOID:0000000006939174

REMOVAL

1.

Remove the battery Refer to 

PG-112, "Removal and Installation"

.

2.

Remove the air cleaner assembly and air ducts.

3.

Disconnect the following unit connectors:
• ECM 
• TCM
• IPDM  E/R

4.

Remove the battery tray.

5.

Disconnect the starter motor harness connectors.

6.

Remove the starter motor mounting bolts, using power tools.

7.

Remove the starter motor.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:

Be careful to tighten “B” terminal nut to the specified torque.

JPBIA1777GB

1.

Magnetic switch assembly

2.

Dust cover kit

3.

Gear case assembly

4.

Pinion assembly

5.

Stopper

6.

Ring

7.

Ring

8.

Stopper

9.

Yoke assembly

10. Armature assembly

11.

Brush holder assembly

12. Metal

13. Rear cover

14. Gear assembly

15. Shift lever set

16. Clutch gear assembly

17. Center bracket

18. Packing

19. Gear shaft

: N·m (kg-m, in-lb)

Revision: 2012 March

2011 Murano CrossCabriolet

STARTER MOTOR

STR-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

L

M

A

STR

N

P

O

Inspection

INFOID:0000000006939175

INSPECTION AFTER DISASSEMBLY

Pinion/Clutch Check

1.

Inspect pinion teeth.
• Replace pinion if teeth are worn or damaged. (Also check condition of ring gear teeth.)

2.

Inspect reduction gear teeth.
• Replace reduction gear if teeth are worn or damaged. (Also check condition of armature shaft gear

teeth.)

3.

Check to see if pinion locks in one direction and rotates smoothly in the opposite direction.
• If it locks or rotates in both directions, or unusual resistance is evident, replace.

Revision: 2012 March

2011 Murano CrossCabriolet

STR-18

< SERVICE DATA AND SPECIFICATIONS (SDS) 

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Starter Motor

INFOID:0000000006939176

Type

M000TA0072

MITSUBISHI make

Reduction gear type

System voltage

(V)

12

No-load

Terminal voltage

(V)

11

Current

(A)

Less than 90

Revolution

(rpm)

More than 2,400

Minimum diameter of commutator

[mm (in)]

28.0 (1.102)

Minimum length of brush

[mm (in)]

5.5 (0.217)

Brush spring tension

[N (kg, lb)]

15.0 - 20.4 (1.5 - 3.4)

Clearance between bearing metal and armature shaft

[mm (in)]

Less than 0.2 (0.008)

Clearance between pinion front edge and pinion stopper

[mm (in)]

0.5 - 2.0 (0.020 - 0.079)

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-1

VENTILATION, HEATER & AIR CONDITIONER

C

D

E

F

G

H

J

K

L

M

SECTION 

VTL

A

B

VTL

N

O

P

CONTENTS

VENTILATION SYSTEM

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

PREPARATION ............................................

4

PREPARATION ...................................................

4

Commercial Service Tool  ..........................................

4

SYSTEM DESCRIPTION  ..............................

5

VENTILATION SYSTEM  .....................................

5

System Description  ...................................................

5

REMOVAL AND INSTALLATION ................

7

DUCT AND GRILLE ............................................

7

Exploded View  ..........................................................

7

CENTER VENTILATOR GRILLE  ................................

8

CENTER VENTILATOR GRILLE : Removal and 
Installation .................................................................

8

SIDE VENTILATOR GRILLE .......................................

9

SIDE VENTILATOR GRILLE : Removal and In-
stallation ....................................................................

9

SIDE DEFROSTER GRILLE  .......................................

9

SIDE DEFROSTER GRILLE : Removal and In-
stallation ....................................................................

9

VENTILATOR DUCT  ...................................................

9

VENTILATOR DUCT : Removal and Installation ......

9

UPPER VENTILATOR DUCT  ....................................

10

UPPER VENTILATOR DUCT : Removal and In-
stallation ..................................................................

10

DEFROSTER NOZZLE AND SIDE DEFROSTER 
NOZZLE .....................................................................

10

DEFROSTER NOZZLE AND SIDE DEFROSTER 
NOZZLE : Removal and Installation  ........................

10

FRONT FOOT DUCT  .................................................

11

FRONT FOOT DUCT : Removal and Installation ....

11

HEATER DUCT ..........................................................

12

HEATER DUCT : Removal and Installation .............

12

REAR FOOT DUCT 1  ................................................

12

REAR FOOT DUCT 1 : Removal and Installation ....

12

REAR FOOT DUCT 2  ................................................

12

REAR FOOT DUCT 2 : Removal and Installation ....

13

REAR FOOT DUCT 3  ................................................

13

REAR FOOT DUCT 3 : Removal and Installation ....

13

REAR VENTILATOR DUCT 1  ...................................

14

REAR VENTILATOR DUCT 1 : Removal and In-
stallation ..................................................................

14

REAR VENTILATOR DUCT 2  ...................................

14

REAR VENTILATOR DUCT 2 : Removal and In-
stallation ..................................................................

14

REAR VENTILATOR DUCT 3  ...................................

15

REAR VENTILATOR DUCT 3 : Removal and In-
stallation ..................................................................

15

REAR VENTILATOR GRILLE  ...................................

15

REAR VENTILATOR GRILLE : Removal and In-
stallation ..................................................................

15

BLOWER UNIT  .................................................

17

Exploded View .........................................................

17

Removal and Installation  .........................................

18

BLOWER MOTOR  ............................................

20

Exploded View .........................................................

20

Removal and Installation  .........................................

20

IN-CABIN MICROFILTER  .................................

21

Exploded View .........................................................

21

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-2

Removal and Installation  ........................................

21

Replacement ..........................................................

21

SERVICE DATA AND SPECIFICATIONS 
(SDS) ...........................................................

22

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

22

In-cabin microfilter ...................................................

22

Revision: 2012 March

2011 Murano CrossCabriolet

PRECAUTIONS

VTL-3

< PRECAUTION >

C

D

E

F

G

H

J

K

L

M

A

B

VTL

N

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000007230834

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.

WARNING:

Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.

• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-

vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the

ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.

• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-4

< PREPARATION >

PREPARATION

PREPARATION

PREPARATION

Commercial Service Tool

INFOID:0000000007230835

Tool name

Description

Remover tool

Removes clips, pawls and metal clips

JMKIA3050ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

VENTILATION SYSTEM

VTL-5

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

J

K

L

M

A

B

VTL

N

O

P

SYSTEM DESCRIPTION

VENTILATION SYSTEM

System Description

INFOID:0000000007230836

SWITCH AND THEIR CONTROL FUNCTION

JPIIA0445GB

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-6

< SYSTEM DESCRIPTION >

VENTILATION SYSTEM

*: Inlet status is displayed by indicator during activating automatic control

AIR DISTRIBUTION

Switch/Dial position

Door position

Mode door

In

ta

ke

 do

or

Up

pe

r ve

nt

ila

to

r do

or

Air mix door

V

e

n

tila

to

r do

or

M

ax

. co

ol do

or

De

fros

te

r do

or

Fo

ot

 do

or

(Driver side)

(Pa

sse

ng

er s

id

e

)

AUTO switch

AUTO

—

—

—

—

MODE switch

A

A

A

A

B

B

A

B

C

B

B

C

C

B

B

B

DEF switch

C

C

C

A

Intake switch

*

—

—

—

—

A

B

UPPER VENT switch

—

A – B

C

Temperature control 
dial (Driver side)

DUAL 
switch: 
OFF

60

°

F

—

A

A

61

°

F – 89 

°

F

AUTO

AUTO

90

°

F

B

B

DUAL 
switch: 
ON

60

°

F

A

—

61

°

F – 89 

°

F

AUTO

90

°

F

B

Temperature control dial (Passen-
ger side)

60

°

F

—

A

61

°

F – 89 

°

F

AUTO

90

°

F

B

ON·OFF switch

OFF

C

B

B

C

—

Discharge air flow

MODE/DEF 

set position

Condition

Air outlet/distribution

Ventilator

Foot

Defroster

Front

Upper

Rear

Front

Rear

Center

Side

• DUAL 

switch: 
OFF

• UPPER 

VENT 
switch: 
ON

40%

41%

8%

11%

—

—

—

18%

24%

10%

17%

23%

8%

—

—

12%

12%

15.5%

27.5%

12%

21%

—

11%

11%

14%

24%

11%

29%

—

11%

10.5%

12.5%

—

—

66%

Revision: 2012 March

2011 Murano CrossCabriolet

DUCT AND GRILLE

VTL-7

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

J

K

L

M

A

B

VTL

N

O

P

REMOVAL AND INSTALLATION

DUCT AND GRILLE

Exploded View

INFOID:0000000007230838

FRONT

REAR

1.

Defroster nozzle

2.

Side defroster nozzle LH

3.

Front foot duct LH

4.

Heater duct

5.

Heater & cooling unit assembly

6.

Ventilator duct

7.

Side defroster grille LH

8.

Instrument panel assembly

9.

Side ventilator grille LH

10. Center ventilator grille assembly

11. Side ventilator grille RH

12. Side defroster grille RH

13. Center speaker grille

14. Blower unit assembly

15. Front foot duct RH

16. Side defroster nozzle RH

17. Upper ventilator duct

JPIIA1225ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-8

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

CENTER VENTILATOR GRILLE

CENTER VENTILATOR GRILLE : Removal and Installation

INFOID:0000000007230839

REMOVAL

1.

Remove cluster lid A. Refer to 

IP-12, "Exploded View"

.

2.

Remove cluster lid D. Refer to 

IP-12, "Exploded View"

.

3.

Remove fixing screws (A).

4.

Pull out center ventilator grille assembly (1) toward instrument
panel assembly to remove.

INSTALLATION

1.

Heater & cooling unit assembly

2.

Rear foot duct 1 LH

3.

Rear foot duct 2 LH

4.

Rear foot duct 3 LH

5.

Rear ventilator duct 1

6.

Rear ventilator duct 2

7.

Rear ventilator duct 3

8.

Console rear finisher

9.

Rear ventilator grille

10.

Rear foot duct 3 RH

11.

Rear foot duct 2 RH

12. Rear foot duct 1 RH

: Clip

: Pawl

JMIIA1899ZZ

: Clip

: Pawl

JMJIA1325ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

DUCT AND GRILLE

VTL-9

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

J

K

L

M

A

B

VTL

N

O

P

Install in the reverse order of removal.

SIDE VENTILATOR GRILLE

SIDE VENTILATOR GRILLE : Removal and Installation

INFOID:0000000007230840

REMOVAL

1.

Remove instrument side finisher. Refer to 

IP-12, "Exploded View"

.

2.

Remove fixing screw (A).

3.

Disengage fixing metal clips using a remover tool (B), and then
remove side ventilator grille (1).

INSTALLATION

Install in the reverse order of removal.

SIDE DEFROSTER GRILLE

SIDE DEFROSTER GRILLE : Removal and Installation

INFOID:0000000007230841

REMOVAL

1.

Remove instrument panel assembly. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove defroster nozzle and side defroster nozzle. Refer to 

VTL-10, "DEFROSTER NOZZLE AND SIDE

DEFROSTER NOZZLE : Removal and Installation"

.

3.

Remove fixing screws (A), and then remove side defroster grille
(1).

INSTALLATION

Install in the reverse order of removal.

VENTILATOR DUCT

VENTILATOR DUCT : Removal and Installation

INFOID:0000000007230842

REMOVAL

1.

Remove instrument panel assembly. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove defroster nozzle and side defroster nozzle. Refer to 

VTL-10, "DEFROSTER NOZZLE AND SIDE

DEFROSTER NOZZLE : Removal and Installation"

.

: Metal clip

JPIIA0583ZZ

JPIIA0584ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-10

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

3.

Remove fixing screws (A), and then remove ventilator duct (1).

INSTALLATION

Install in the reverse order of removal.

UPPER VENTILATOR DUCT

UPPER VENTILATOR DUCT : Removal and Installation

INFOID:0000000007233014

REMOVAL

1.

Remove instrument panel assembly. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove defroster nozzle and side defroster nozzle. Refer to 

VTL-10, "DEFROSTER NOZZLE AND SIDE

DEFROSTER NOZZLE : Removal and Installation"

.

3.

Remove fixing screws (A), and then remove upper ventilator
duct (1).

INSTALLATION

Install in the reverse order of removal.

DEFROSTER NOZZLE AND SIDE DEFROSTER NOZZLE

DEFROSTER NOZZLE AND SIDE DEFROSTER NOZZLE : Removal and Installation

INFOID:0000000007230843

REMOVAL

1.

Remove instrument panel assembly. Refer to 

IP-12, "Exploded View"

. 

JPIIA0585ZZ

JPIIA0586ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

DUCT AND GRILLE

VTL-11

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

J

K

L

M

A

B

VTL

N

O

P

2.

Remove mounting screws (A), and then remove defroster nozzle (1), side defroster nozzle RH (2) and
side defroster nozzle LH (3) from instrument panel assembly as a set. 

3.

Remove side defroster nozzle (LH and RH) from defroster nozzle. 

INSTALLATION

Install in the reverse order of removal.

FRONT FOOT DUCT

FRONT FOOT DUCT : Removal and Installation

INFOID:0000000007230847

REMOVAL

Driver Side

1.

Remove instrument lower panel LH. Refer to 

IP-13, "Removal and Installation"

.

2.

Remove fixing screws (A), and then remove front foot duct LH
(1).

Passenger Side

1.

Remove blower unit assembly. Refer to 

VTL-18, "Removal and Installation"

.

2.

Remove fixing screws (A), and harness clip, and then remove
front foot duct RH (1).

INSTALLATION

Install in the reverse order of removal.

JPIIA0587ZZ

: Vehicle front

JPIIA1226ZZ

: Vehicle front

JPIIA1227ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

VTL-12

< REMOVAL AND INSTALLATION >

DUCT AND GRILLE

HEATER DUCT

HEATER DUCT : Removal and Installation

INFOID:0000000007257126

REMOVAL

1.

Remove instrument lower panel LH. Refer to 

IP-13, "Removal and Installation"

. 

2.

Remove fixing screw (A), and then remove heater duct (1). 

INSTALLATION

Install in the reverse order of removal.

REAR FOOT DUCT 1

REAR FOOT DUCT 1 : Removal and Installation

INFOID:0000000007230845

REMOVAL

Driver Side

1.

Remove instrument lower cover LH. Refer to 

IP-21, "Removal and Installation"

.

2.

Remove rear foot duct 1 LH (1).

Passenger Side

1.

Remove instrument lower cover RH. Refer to 

IP-21, "Removal and Installation"

.

2.

Remove rear foot duct 1 RH (1).

INSTALLATION

Install in the reverse order of removal.

REAR FOOT DUCT 2

JPIIA0599ZZ

JPIIA0595ZZ

JPIIA0596ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

DUCT AND GRILLE

VTL-13

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

J

K

L

M

A

B

VTL

N

O

P

REAR FOOT DUCT 2 : Removal and Installation

INFOID:0000000007256339

REMOVAL

Driver Side

1.

Remove rear foot duct 1 LH. Refer to 

VTL-12, "REAR FOOT DUCT 1 : Removal and Installation"

.

2.

Pull up driver side floor carpet of secure work space. Refer to 

INT-24, "Exploded View"

.

3.

Remove fixing clip (A), and then remove rear foot duct 2 LH (1).

Passenger Side

1.

Remove rear foot duct 1 RH. Refer to 

VTL-12, "REAR FOOT DUCT 1 : Removal and Installation"

.

2.

Pull up passenger side floor carpet of secure work space. Refer to 

INT-24, "Exploded View"

.

3.

Remove fixing clip (A), and then remove rear foot duct 2 RH (1).

INSTALLATION

Install in the reverse order of removal.

REAR FOOT DUCT 3

REAR FOOT DUCT 3 : Removal and Installation

INFOID:0000000007256340

REMOVAL

Driver Side

1.

Remove rear foot duct 2 LH. Refer to 

VTL-13, "REAR FOOT DUCT 2 : Removal and Installation"

.

2.

Remove fixing screw (A), and then remove rear foot duct 3 LH
(1).

Passenger Side

1.

Remove rear foot duct 2 LH. Refer to 

VTL-13, "REAR FOOT DUCT 2 : Removal and Installation"

.

JPIIA0597ZZ

JPIIA0598ZZ

JPIIA0593ZZ

Revision: 2012 March

2011 Murano CrossCabriolet