Murano Cross Cabriolet Z51 (2011 year). Manual - part 53

 

  Index      Manuals     Murano Cross Cabriolet Z51 (2011 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     51      52      53      54     ..

 

 

Murano Cross Cabriolet Z51 (2011 year). Manual - part 53

 

 

FRONT PASSENGER AIR BAG MODULE

SR-17

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

FRONT PASSENGER AIR BAG MODULE

Exploded View

INFOID:0000000007228839

Removal and Installation

INFOID:0000000007228840

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-

utes or more.

• Always work from the side of air bag module. Never work in front of it.
• Never use air tools or electric tools for servicing.

REMOVAL

1.

Remove instrument panel assembly. Refer to 

IP-13, "Removal and Installation"

.

2.

Disconnect front passenger air bag harness connector (A).

3.

Remove front passenger air bag module mounting bolt (B).
NOTE:
The figure shows the installed front passenger air bag module.
(Under view of the module installed without glove box cover.)

1.

Instrument panel assembly

2.

Front passenger air bag module

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA0509GB

JMHIA0510ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

SR-18

< REMOVAL AND INSTALLATION >

FRONT PASSENGER AIR BAG MODULE

4.

Remove front passenger air bag module fixing screws (B) from
instrument panel assembly (1).

5.

Disconnect pawls (C) by using remover tool (A), and then
remove front passenger air bag module (2) from instrument
panel assembly.

CAUTION:

• Always place the front passenger air bag module with pad

side facing upward.

• Never impact the passenger air bag module.
• Replace the front passenger air bag module if it is dropped or

sustains an impact.

• Never insert any foreign objects (screwdriver, etc.) into front passenger air bag module.
• Never disassembly the front passenger air bag module.
• Never expose the front passenger air bag module to temperatures exceeding 90 

°

C (194 

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the front passenger air bag mod-

ule.

INSTALLATION

Install in the reverse order of removal.

CAUTION:

• Never reuse fixing bolts after removal, replace with new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-17, "CONSULT

Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp. 

JMHIA0511ZZ

: Upward

JMHIA0512ZZ

JMHIA0009ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

DOOR-MOUNTED CURTAIN AIR BAG MODULE

SR-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

DOOR-MOUNTED CURTAIN AIR BAG MODULE 

Exploded View

INFOID:0000000007228855

Removal and Installation

INFOID:0000000007228856

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-

utes or more.

• Before starting removal and installation operation, always eliminate static electricity from door fin-

isher, door-mounted curtain air bag module, and body of the technician (to prevent an accidental
activation due to static electricity).

• Never use air tools or electric tools for servicing.
• When replacing door-mounted curtain air bag module, always replace it together with door finisher

as a set.

REMOVAL

1.

Remove door finisher. Refer to 

INT-13, "Removal and Installation"

.

CAUTION:

Disconnect first the door-mounted curtain air bag harness connector before disconnecting the
other harness connectors. 

JMHIA2064GB

1.

Door finisher

2.

Door-mounted curtain air bag module

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

Revision: 2012 March

2011 Murano CrossCabriolet

SR-20

< REMOVAL AND INSTALLATION >

DOOR-MOUNTED CURTAIN AIR BAG MODULE

2.

Remove door-mounted curtain air bag module fixing screws (A)
and mounting bolts (B).

3.

Remove door-mounted curtain air bag module.

CAUTION:

• Never place any object in deploying path of door-mounted

curtain air bag module. Never lean door-mounted curtain air
bag module against wall or others.

• Always place air bag module so that inflator label is visible.

• Never impact the door-mounted curtain air bag module.
• Replace door-mounted curtain air bag module if it is dropped

or sustains an impact. 

• Never insert any foreign objects (screwdriver, etc.) into the door-mounted curtain air bag module.
• Never disassemble the door-mounted curtain air bag module.
• Never expose the door-mounted curtain air bag module to temperatures exceeding 90

°

C (194

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the door-mounted curtain air bag

module.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• When removing door-mounted curtain air bag module from door finisher, never reuse door finisher.
• Never forget to tighten the mounting bolts and fixing screws of door-mounted curtain air bag mod-

ule.

• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-13, "On Board Diag-

nosis Function"

 or 

SRC-17, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

JMHIA2065ZZ

: Upward

JMHIA2066ZZ

JMHIA0009ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

POP-UP ROLL BAR

SR-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

POP-UP ROLL BAR 

Exploded View

INFOID:0000000007228859

Removal and Installation

INFOID:0000000007228860

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-

utes or more.

• Never use air tools or electric tools for servicing.
• When repairing, removing and installing pop-up roll bar, always refer to SRS AIR BAG and SRS AIR

BAG CONTROL SYSTEM.

CAUTION:

1.

Pup-up roll bar assembly

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA2068GB

Revision: 2012 March

2011 Murano CrossCabriolet

SR-22

< REMOVAL AND INSTALLATION >

POP-UP ROLL BAR

Glass breaking pin is sharp. For safety purposes, protect glass breaking pin (A) of pop-up roll bar
using polystyrene foam or rubber sheet so that glass breaking pin does not contact operator during
removal and installation.

REMOVAL

1.

Open trunk lid.

2.

Remove trunk front finisher. Refer to 

INT-36, "TRUNK FRONT FINISHER : Removal and Installation"

.

3.

Remove pop-up roll bar assembly mounting bolts (A) for trunk
room side.

4.

Close trunk lid.

5.

Fully open soft top.

6.

Remove rear seatback. Refer to 

SE-57, "SEATBACK : Removal and Installation"

.

7.

Remove rear parcel shelf front finisher. Refer to 

INT-30, "REAR PARCEL SHELF FRONT FINISHER :

Removal and Installation"

.

8.

Remove pop-up roll bar assembly mounting bolts (A) for rear
seatback side.

9.

Disconnect pop-up roll bar assembly harness connector (A).

10. Pull up and remove pop-up roll bar assembly.

JMHIA2093ZZ

: Vehicle front 

JMHIA2071ZZ

: Vehicle front 

JMHIA2070ZZ

: Vehicle front 

JMHIA2069ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

POP-UP ROLL BAR

SR-23

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

CAUTION:

• Always place the pop-up roll bar assembly with special bolts

side facing upward.

• Never place any object in deploying path of pop-up roll bar

assembly. Never lean pop-up roll bar assembly against a wall
or others.

• Never impact the pop-up roll bar assembly.
• Replace pop-up roll bar assembly if it is dropped or sustained

an impact. 

• Never insert any foreign objects (screwdriver, etc.) into the pop-up roll bar assembly.
• Never disassemble the pop-up roll bar assembly.
• Never expose the pop-up roll bar assembly to temperatures of more than 90

°

C (194

°

F).

• Never allow oil, grease, detergent, or water to come in contact with the pop-up roll bar assembly.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never reuse old mounting bolts after removal, replace with new bolts.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-13, "On Board Diag-

nosis Function"

 or 

SRC-17, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

Removal When Pop-up Roll Bar is Activated While Soft Top is Closed

When rear glass is broken and pop-up roll bar is deployed

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 minutes
or more.

CAUTION:

Remove broken pieces of rear glass in advance for preventing injury.

1.

Open trunk lid.

2.

Remove trunk front finisher. Refer to 

INT-36, "TRUNK FRONT FINISHER : Removal and Installation"

.

: Upward 

JMHIA2072ZZ

JMHIA0009ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

SR-24

< REMOVAL AND INSTALLATION >

POP-UP ROLL BAR

3.

Remove pop-up roll bar assembly mounting bolts (A) of trunk
room side.

4.

Close trunk lid.

5.

Remove rear seatback. Refer to 

SE-57, "SEATBACK : Removal and Installation"

.

6.

Remove rear parcel shelf front finisher. Refer to 

INT-30, "REAR PARCEL SHELF FRONT FINISHER :

Removal and Installation"

.

7.

Remove pop-up roll bar assembly mounting bolts (A) of rear
seatback side.

8.

Disconnect pop-up roll bar assembly harness connector (A).

9.

Pull out pop-up roll bar from rear glass portion to upward.

When pop-up roll bar is deployed and rear glass is not broken

WARNING:

Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 minutes
or more.

1.

Open trunk lid.

2.

Remove trunk front finisher. Refer to 

INT-36, "TRUNK FRONT FINISHER : Removal and Installation"

.

: Vehicle front 

JMHIA2071ZZ

: Vehicle front 

JMHIA2070ZZ

: Vehicle front 

JMHIA2069ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

POP-UP ROLL BAR

SR-25

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

3.

Remove pop-up roll bar assembly mounting bolts (A) of trunk
room side.

4.

Close trunk lid.

5.

Slide down pop-up roll bar.

CAUTION:

Fix pop-up roll bar using fixing band so that pop-up roll bar may not move upward.

6.

Fully open soft top.

7.

Remove rear seatback. Refer to 

SE-57, "SEATBACK : Removal and Installation"

.

8.

Remove rear parcel shelf front finisher. Refer to 

INT-30, "REAR PARCEL SHELF FRONT FINISHER :

Removal and Installation"

.

9.

Remove pop-up roll bar assembly mounting bolts (A) of rear
seatback side.

10. Disconnect pop-up roll bar assembly harness connector (A).

11. Pull up and remove pop-up roll bar assembly.

: Vehicle front 

JMHIA2071ZZ

: Vehicle front 

JMHIA2070ZZ

: Vehicle front 

JMHIA2069ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

SR-26

< REMOVAL AND INSTALLATION >

CRASH ZONE SENSOR

CRASH ZONE SENSOR

Exploded View

INFOID:0000000007228843

Removal and Installation

INFOID:0000000007228844

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-

utes or more.

• Never use air tools or electric tools for servicing.

REMOVAL

1.

Remove radiator cover grill (RH). Refer to 

EM-24, "Exploded View"

.

2.

Remove air duct (inlet). Refer to 

EM-26, "Exploded View"

.

3.

Remove crash zone sensor fixing nuts.

4.

Disconnect crash zone sensor harness connector, and then remove the crash zone sensor.

CAUTION:

• Never impact the crash zone sensor.
• Replace the crash zone sensor if it is dropped or sustains an

impact.

• Replace the crash zone sensor of deployed SRS driver air bag and deployed SRS front passenger air

bag. 

INSTALLATION

1.

Crash zone sensor

A

: Crash zone sensor harness connector

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA0515GB

JMHIA0009ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

CRASH ZONE SENSOR

SR-27

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

Install in the reverse order of removal.

CAUTION:

• Never reuse old fixing nuts after removal, replace with new nuts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-17, "CONSULT

Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp. 

Revision: 2012 March

2011 Murano CrossCabriolet

SR-28

< REMOVAL AND INSTALLATION >

SATELLITE SENSOR

SATELLITE SENSOR

Exploded View

INFOID:0000000007228898

Removal and Installation

INFOID:0000000007228899

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-

utes or more.

• Never use air tools or electric tools for servicing.

DOOR SATELLITE SENSOR

Removal

1.

Remove door finisher. Refer to 

INT-13, "Removal and Installation"

. 

2.

Remove door satellite sensor mounting bolt.

3.

Disconnect harness connector, and then remove door satellite sensor.

CAUTION:

1.

Door satellite sensor

2.

Satellite sensor

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA2067GB

Revision: 2012 March

2011 Murano CrossCabriolet

SATELLITE SENSOR

SR-29

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

• Never impact the door satellite sensor.
• Replace the door satellite sensor if it is dropped or sustains

an impact.

• Replace the door satellite sensor of deployed side air bag module and deployed door-mounted cur-

tain air bag module. 

Installation

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never reuse fixing nut after removal, replace with new nut.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-13, "On Board Diag-

nosis Function"

 or 

SRC-17, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

SATELLITE SENSOR

Removal

1.

Remove rear side finisher. Refer to 

INT-22, "REAR SIDE FINISHER : Removal and Installation"

. 

2.

Remove front seat belt retractor. Refer to 

SB-5, "SEAT BELT RETRACTOR : Removal and Installation"

. 

3.

Remove satellite sensor mounting nut.

4.

Disconnect harness connector, and then remove satellite sensor.

CAUTION:

• Never impact the satellite sensor.
• Replace the satellite sensor if it is dropped or sustains an

impact.

• Replace the satellite sensor of deployed side air bag module and deployed door-mounted curtain air

bag module. 

Installation

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Never reuse fixing nut after removal, replace with new nut.
• Never damage the harness while installing.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-13, "On Board Diag-

nosis Function"

 or 

SRC-17, "CONSULT Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.

JMHIA0009ZZ

JMHIA0009ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

SR-30

< REMOVAL AND INSTALLATION >

DIAGNOSIS SENSOR UNIT

DIAGNOSIS SENSOR UNIT

Exploded View

INFOID:0000000007228847

Removal and Installation

INFOID:0000000007228848

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait for 3 min-

utes or more.

• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-

ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.

• Never use air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-

est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.

REMOVAL

1.

Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT.

2.

Disconnect each connector of all air bag modules and pre-tensioner seat belts.

3.

Remove instrument lower cover (LH and RH). Refer to 

IP-12, "Exploded View"

.

4.

Remove rear foot duct 1 (LH and RH). Refer to 

VTL-7, "Exploded View"

.

5.

Remove instrument stay LH. Refer to 

IP-12, "Exploded View"

.

6.

Remove front console bracket. Refer to 

IP-12, "Exploded View"

.

7.

Disconnect diagnosis sensor unit harness connectors.

8.

Remove fixing bolts, ground bolt, and then remove diagnosis sensor unit. 

CAUTION:

1.

Diagnosis sensor unit

A

: Diagnosis sensor unit harness connector

B

: Ground bolt

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JMHIA0517GB

Revision: 2012 March

2011 Murano CrossCabriolet

DIAGNOSIS SENSOR UNIT

SR-31

< REMOVAL AND INSTALLATION >

C

D

E

F

G

I

J

K

L

M

A

B

SR

N

O

P

• Replace the diagnosis sensor unit if it is dropped or sustains

an impact.

• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-

tensioner. 

INSTALLATION

Install air bag diagnosis sensor unit in the reverse order of removal.

CAUTION:

• Never reuse mounting bolts after removal, replace with new mounting bolts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-

tioning parts, reset the memory using self-diagnosis or CONSULT. Refer to 

SRC-17, "CONSULT

Function"

.

• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT that the ECU discrimi-

nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.

NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit is installed.

JMHIA0009ZZ

Revision: 2012 March

2011 Murano CrossCabriolet

SR-32

< REMOVAL AND INSTALLATION >

FRONT SEAT BELT PRE-TENSIONER

FRONT SEAT BELT PRE-TENSIONER

Removal and Installation

INFOID:0000000007228849

For removal and installation procedures, refer to 

SB-5, "SEAT BELT RETRACTOR : Removal and Installa-

tion"

.

Revision: 2012 March

2011 Murano CrossCabriolet

 

 

 

 

 

 

 

Content      ..     51      52      53      54     ..