Nissan Murano Z50 (2003 year). Manual - part 216

LAN-1070

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

Case 12

Check AWD control unit circuit. Refer to 

LAN-1080, "AWD Control Unit Circuit Check"

 .

PKIB1082E

SKIA5526E

CAN SYSTEM (TYPE 31)

LAN-1071

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

Case 13

Check ABS actuator and electric unit (control unit) circuit. Refer to 

LAN-1080, "ABS Actuator and Electric Unit

(Control Unit) Circuit Check"

 .

PKIB1083E

SKIA5527E

LAN-1072

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

Case 14

Check IPDM E/R circuit. Refer to 

LAN-1081, "IPDM E/R Circuit Check"

 .

Case 15

Check CAN communication circuit. Refer to 

LAN-1082, "CAN Communication Circuit Check"

 .

PKIB1084E

SKIA5528E

PKIB1085E

CAN SYSTEM (TYPE 31)

LAN-1073

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

Case 16

Check IPDM E/R ignition relay circuit continuously sticks “OFF”. Refer to 

LAN-1086, "IPDM E/R Ignition Relay

Circuit Check"

 .

Case 17

Check IPDM E/R ignition relay circuit continuously sticks “ON”. Refer to 

LAN-1086, "IPDM E/R Ignition Relay

Circuit Check"

 .

PKIB1086E

PKIB1087E

LAN-1074

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

Circuit Check Between TCM and Data Link Connector

AKS00780

1. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Disconnect ECM connector and harness connector M82.

4.

Check continuity between harness connector M82 terminals 8
(L), 9 (Y) and data link connector M24 terminals 6 (L), 14 (Y).

OK or NG

OK

>> Connect all the connectors and diagnose again. Refer to

LAN-1055, "Work Flow"

 .

NG

>> Repair harness.

Circuit Check Between Data Link Connector and Driver Seat Control Unit

AKS00781

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check following terminals and connectors for damage, bend and loose connection (connector side and
harness side).

●

Harness connector M9

●

Harness connector B2

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect harness connector M9.

2.

Check continuity between data link connector M24 terminals 6
(L), 14 (Y) and harness connector M9 terminals 1 (L), 10 (Y).

OK or NG

OK

>> GO TO 3.

NG

>> Repair harness.

8 (L) - 6 (L)

: Continuity should exist.

9 (Y) - 14 (Y)

: Continuity should exist.

SKIA5014E

6 (L) - 1 (L)

: Continuity should exist.

14 (Y) - 10 (Y)

: Continuity should exist.

SKIA5015E

CAN SYSTEM (TYPE 31)

LAN-1075

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

3. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect harness connector B4.

2.

Check continuity between harness connector B2 terminals 1 (L),
10 (Y) and harness connector B4 terminals 3 (L), 10 (Y).

OK or NG

OK

>> Connect all the connectors and diagnose again. Refer to

LAN-1055, "Work Flow"

 .

NG

>> Repair harness.

Circuit Check Between Driver Seat Control Unit and ABS Actuator and Electric 
Unit (Control Unit)

AKS00782

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check following terminals and connectors for damage, bend and loose connection (connector side and
harness side).

●

Harness connector B4

●

Harness connector E105

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect harness connector B2 and harness connector B4.

2.

Check continuity between harness connector B2 terminals 1 (L),
10 (Y) and harness connector B4 terminals 3 (L), 10 (Y).

OK or NG

OK

>> GO TO 3.

NG

>> Repair harness.

1 (L) - 3 (L)

: Continuity should exist.

10 (Y) - 10 (Y)

: Continuity should exist.

SKIA5016E

1 (L) - 3 (L)

: Continuity should exist.

10 (Y) - 10 (Y)

: Continuity should exist.

SKIA5016E

LAN-1076

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

3. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect ABS actuator and electric unit (control unit) connector.

2.

Check continuity between harness connector E105 terminals 3
(L), 10 (Y) and ABS actuator and electric unit (control unit) har-
ness connector E24 terminals 11 (L), 15 (Y).

OK or NG

OK

>> Connect all the connectors and diagnose again. Refer to

LAN-1055, "Work Flow"

 .

NG

>> Repair harness.

ECM Circuit Check

AKS00783

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of ECM for damage, bend and loose connection (control module side and
harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect ECM connector.

2.

Check resistance between ECM harness connector M80 termi-
nals 94 (L) and 86 (Y).

OK or NG

OK

>> Replace ECM.

NG

>> Repair harness between ECM and TCM.

TCM Circuit Check

AKS00784

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check following terminals and connectors for damage, bend and loose connection (control module side
and harness side).

●

TCM connector

●

Harness connector F102

●

Harness connector M82

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

3 (L) - 11 (L) 

: Continuity should exist.

10 (Y) - 15 (Y) 

: Continuity should exist.

SKIA5017E

94 (L) - 86 (Y) 

: Approx. 108 - 132

Ω

PKIA0816E

CAN SYSTEM (TYPE 31)

LAN-1077

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect TCM connector.

2.

Check resistance between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).

OK or NG

OK

>> Replace TCM.

NG

>> Repair harness between TCM and ECM.

Display Control Unit Circuit Check

AKS00785

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of display control unit for damage, bend and loose connection (control unit
side and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect display control unit connector.

2.

Check resistance between display control unit harness connec-
tor M43 terminals 25 (L) and 26 (Y).

OK or NG

OK

>> Replace display control unit.

NG

>> Repair harness between display control unit and data

link connector.

Data Link Connector Circuit Check

AKS00786

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check data link connector and terminals for damage, bend and loose connection (connector side and har-
ness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

5 (L) - 6 (Y) 

: Approx. 54 - 66

Ω

PKIA0817E

25 (L) - 26 (Y) 

: Approx. 54 - 66

Ω

SKIA5023E

LAN-1078

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR OPEN CIRCUIT

Check resistance between data link connector M24 terminals 6 (L)
and 14 (Y).

OK or NG

OK

>> Diagnose again. Refer to 

LAN-1055, "Work Flow"

 .

NG

>> Repair harness between data link connector and BCM.

BCM Circuit Check

AKS00787

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of BCM for damage, bend and loose connection (control module side and
harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect BCM connector.

2.

Check resistance between BCM harness connector M37 termi-
nals 70 (L) and 71 (Y).

OK or NG

OK

>> Replace BCM. Refer to 

BCS-36, "Removal and Installa-

tion of BCM"

 .

NG

>> Repair harness between BCM and data link connector.

Unified Meter and A/C Amp. Circuit Check

AKS00788

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of unified meter and A/C amp. for damage, bend and loose connection
(meter side and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

6 (L) - 14 (Y) 

: Approx. 54 - 66

Ω

PKIA2077E

70 (L) - 71 (Y) 

: Approx. 54 - 66

Ω

LKIA0028E

CAN SYSTEM (TYPE 31)

LAN-1079

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect unified meter and A/C amp. connector.

2.

Check resistance between unified meter and A/C amp. harness
connector M49 terminals 1 (L) and 11 (Y).

OK or NG

OK

>> Replace unified meter and A/C amp.

NG

>> Repair harness between unified meter and A/C amp.

and data link connector.

Steering Angle Sensor Circuit Check

AKS00789

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of steering angle sensor for damage, bend and loose connection (sensor
side and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect steering angle sensor connector.

2.

Check resistance between steering angle sensor harness con-
nector M33 terminals 4 (L) and 5 (Y).

OK or NG

OK

>> Replace steering angle sensor.

NG

>> Repair harness between steering angle sensor and data

link connector.

Driver Seat Control Unit Circuit Check

AKS0078A

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check following terminals and connectors for damage, bend and loose connection (control unit side and
harness side).

●

Driver seat control unit connector

●

Harness connector B301

●

Harness connector B9

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

1 (L) - 11 (Y) 

: Approx. 54 - 66

Ω

PKIA2078E

4 (L) - 5 (Y)

: Approx. 54 - 66

Ω

PKIA0819E

LAN-1080

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect driver seat control unit connector.

2.

Check resistance between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).

OK or NG

OK

>> Replace driver seat control unit.

NG

>> Repair harness between driver seat control unit and har-

ness connector B4.

AWD Control Unit Circuit Check

AKS0078B

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of AWD control unit for damage, bend and loose connection (control unit
side and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect AWD control unit connector.

2.

Check resistance between AWD control unit harness connector
E111 terminals 8 (L) and 16 (Y).

OK or NG

OK

>> Replace AWD control unit.

NG

>> Repair harness between AWD control unit and IPDM E/

R.

ABS Actuator and Electric Unit (Control Unit) Circuit Check

AKS0078C

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of ABS actuator and electric unit (control unit) for damage, bend and loose
connection (control unit side and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

3 (L/Y) - 19 (BR/W) 

: Approx. 54 - 66

Ω

SKIA5024E

8 (L) - 16 (Y) 

: Approx. 54 - 66

Ω

SKIA5033E

CAN SYSTEM (TYPE 31)

LAN-1081

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect ABS actuator and electric unit (control unit) connector.

2.

Check resistance between ABS actuator and electric unit (con-
trol unit) harness connector E24 terminals 11 (L) and 15 (Y).

OK or NG

OK

>> Replace ABS actuator and electric unit (control unit).

NG

>> Repair harness between ABS actuator and electric unit

(control unit) and IPDM E/R.

IPDM E/R Circuit Check

AKS0078D

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check terminals and connector of IPDM E/R for damage, bend and loose connection (control module side
and harness side).

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect IPDM E/R connector.

2.

Check resistance between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).

OK or NG

OK

>> Replace IPDM E/R.

NG

>> Repair harness between IPDM E/R and ABS actuator

and electric unit (control unit).

11 (L) - 15 (Y) 

: Approx. 54 - 66

Ω

SKIA5019E

48 (L) - 49 (Y) 

: Approx. 108 - 132

Ω

LKIA0030E

LAN-1082

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

CAN Communication Circuit Check

AKS0078E

1. 

CHECK CONNECTOR

1.

Turn ignition switch OFF.

2.

Disconnect the negative battery terminal.

3.

Check following terminals and connectors for damage, bend and loose connection (control module side,
control unit side, meter side, sensor side, and harness side).

●

ECM

●

TCM

●

Display control unit

●

BCM

●

Unified meter and A/C amp.

●

Steering angle sensor

●

Driver seat control unit

●

AWD control unit

●

ABS actuator and electric unit (control unit)

●

IPDM E/R

●

Between ECM and IPDM E/R

●

Between ECM and TCM

●

Between ECM and driver seat control unit

OK or NG

OK

>> GO TO 2.

NG

>> Repair terminal or connector.

2. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect following connectors.

–

ECM connector

–

Harness connector M82

–

Display control unit connector

–

BCM connector

–

Unified meter and A/C amp. connector

–

Steering angle sensor connector

–

Harness connector M9

2.

Check continuity between data link connector M24 terminals 6
(L) and 14 (Y).

OK or NG

OK

>> GO TO 3.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

●

Harness between data link connector and ECM.

●

Harness between data link connector and harness
connector M82.

●

Harness between data link connector and display control unit.

●

Harness between data link connector and BCM.

●

Harness between data link connector and unified meter and A/C amp.

●

Harness between data link connector and steering angle sensor.

●

Harness between data link connector and harness connector M9.

6 (L) - 14 (Y) 

: Continuity should not exist.

PKIA2077E

CAN SYSTEM (TYPE 31)

LAN-1083

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

3. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between data link connector M24 terminals 6 (L),
14 (Y) and ground.

OK or NG

OK

>> GO TO 4.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

●

Harness between data link connector and ECM.

●

Harness between data link connector and harness
connector M82.

●

Harness between data link connector and display control unit.

●

Harness between data link connector and BCM.

●

Harness between data link connector and unified meter and A/C amp.

●

Harness between data link connector and steering angle sensor.

●

Harness between data link connector and harness connector M9.

4. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect TCM connector.

2.

Check continuity between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).

OK or NG

OK

>> GO TO 5.

NG

>> Repair harness between TCM and harness connector

F102.

5. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between TCM harness connector F103 terminals 5
(L), 6 (Y) and ground.

OK or NG

OK

>> GO TO 6.

NG

>> Repair harness between TCM and harness connector

F102.

6 (L) - Ground

: Continuity should not exist.

14 (Y) - Ground

: Continuity should not exist.

PKIA2079E

5 (L) - 6 (Y) 

: Continuity should not exist.

PKIA0817E

5 (L) - Ground

: Continuity should not exist.

6 (Y) - Ground

: Continuity should not exist.

SKIA5020E

LAN-1084

[CAN]

CAN SYSTEM (TYPE 31)

Revision; 2004 April

2003 Murano

6. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect harness connector B4 and harness connector B9.

2.

Check continuity between harness connector B4 terminals 3 (L)
and 10 (Y).

OK or NG

OK

>> GO TO 7.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

●

Repair harness between harness connector B4 and
harness connector B2.

●

Repair harness between harness connector B4 and
harness connector B9.

7. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between harness connector B4 terminals 3 (L), 10
(Y) and ground.

OK or NG

OK

>> GO TO 8.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

●

Repair harness between harness connector B4 and
harness connector B2.

●

Repair harness between harness connector B4 and harness connector B9.

8. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect driver seat control unit connector.

2.

Check continuity between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).

OK or NG

OK

>> GO TO 9.

NG

>> Repair harness between driver seat control unit and har-

ness connector B301.

3 (L) - 10 (Y) 

: Continuity should not exist.

SKIA5021E

3 (L) - Ground

: Continuity should not exist.

10 (Y) - Ground

: Continuity should not exist.

SKIA5022E

3 (L/Y) - 19 (BR/W) 

: Continuity should not exist.

SKIA5024E

CAN SYSTEM (TYPE 31)

LAN-1085

[CAN]

C

D

E

F

G

H

I

J

L

M

A

B

LAN

Revision; 2004 April

2003 Murano

9. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between driver seat control unit harness connector
B303 terminals 3 (L/Y), 19 (BR/W) and ground.

OK or NG

OK

>> GO TO 10.

NG

>> Repair harness between driver seat control unit and har-

ness connector B301.

10. 

CHECK HARNESS FOR SHORT CIRCUIT

1.

Disconnect AWD control unit connector, ABS actuator and electric unit (control unit) connector and IPDM
E/R connector.

2.

Check continuity between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).

OK or NG

OK

>> GO TO 11.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

●

Harness between IPDM E/R and AWD control unit.

●

Harness between IPDM E/R and ABS actuator and
electric unit (control unit).

●

Harness between IPDM E/R and harness connector E105.

11. 

CHECK HARNESS FOR SHORT CIRCUIT

Check continuity between IPDM E/R harness connector E9 termi-
nals 48 (L), 49 (Y) and ground.

OK or NG

OK

>> GO TO 12.

NG

>> Check the following harnesses. If any harness is dam-

aged, repair the harness.

●

Harness between IPDM E/R and AWD control unit.

●

Harness between IPDM E/R and ABS actuator and
electric unit (control unit).

●

Harness between IPDM E/R and harness connector E105.

12. 

ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION

Check components inspection. Refer to 

LAN-1086, "ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION"

 .

OK or NG

OK

>> Connect all the connectors and diagnose again. Refer to 

LAN-1055, "Work Flow"

 .

NG

>> Replace ECM and/or IPDM E/R.

3 (L/Y) - Ground

: Continuity should not exist.

19 (BR/W) - Ground

: Continuity should not exist.

SKIA5025E

48 (L) - 49 (Y) 

: Continuity should not exist.

LKIA0030E

48 (L) - Ground

: Continuity should not exist.

49 (Y) - Ground

: Continuity should not exist.

LKIA0036E