Nissan Murano Z51 (2008 year). Manual

WT-26

< COMPONENT DIAGNOSIS >

C1720, C1721, C1722, C1723 TRANSMITTER

C1720, C1721, C1722, C1723 TRANSMITTER

Description

INFOID:0000000003412914

The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave.

DTC Logic

INFOID:0000000003375963

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT-III

Driving at a speed of 40 km/h (25 MPH) or more for 10 minutes.

Perform BCM self-diagnosis.

Is DTC “C1720”, “C1721”, “C1722”, “C1723” detected?

YES

>> Proceed to diagnosis procedure. Refer to

WT-26, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375964

CHECK ID REGISTRATION

With CONSULT-III

Perform the ID registration of all transmitters. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

Drive at a speed of 40 km/h (25 MPH) or more for 10 minutes.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.

Is the inspection result normal?

YES

>> GO TO 6.

>> GO TO 2.

CHECK ALL TIRE PRESSURE SIGNAL

With CONSULT-III

: Outside

SEIA0768E

DTC

Display item

Malfunction detected condition

Possible case

C1720

[CODE ERR] FL

Function code data from front LH transmitter is malfunction.

• Tire pressure receiver mal-

function

• Transmitter malfunction
• BCM malfunction
• Harness or connector

C1721

[CODE ERR] FR

Function code data from front RH transmitter is malfunction.

C1722

[CODE ERR] RR

Function code data from rear RH transmitter is malfunction.

C1723

[CODE ERR] RL

Function code data from rear LH transmitter is malfunction.

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or
more for 10 minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

C1720, C1721, C1722, C1723 TRANSMITTER

WT-27

< COMPONENT DIAGNOSIS >

Start the engine.

Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.

Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.

Are all tire pressure displayed 0 kPa?

YES

>> GO TO 3.

>> GO TO 5.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

Turn the ignition switch OFF.

Disconnect BCM harness connector and tire pressure receiver harness connector.

Check continuity between BCM harness connector and tire pressure receiver harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace damage parts.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to

WT-36, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts.

>> Replace the tire pressure receiver.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT-III

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Check all tire pressures with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.

Is the inspection result normal?

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or
more for several minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

138

139

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or
more for several minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-28

< COMPONENT DIAGNOSIS >

C1720, C1721, C1722, C1723 TRANSMITTER

YES

>> GO TO 6.

>> Replace BCM. Refer to

BCS-96, "Removal and Installation"

CHECK TRANSMITTER

With CONSULT-III

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Check all tire pressures with CONSULT-III “DATA MONITOR” within 5 minutes after stopped vehicle.

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace malfunction transmitter.

Special Repair Requirement

INFOID:0000000003375965

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to

WT-111, "Tire Air Pressure"

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

PERFORM ID REGISTRATION

Perform ID registration. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

>> END

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or
more for several minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

C1724, C1725, C1726, C1727 TRANSMITTER

WT-29

< COMPONENT DIAGNOSIS >

C1724, C1725, C1726, C1727 TRANSMITTER

Description

INFOID:0000000003412915

The transmitter (1) integrated with a valve is installed on a wheel (2),
and transmits a detected air pressure signal by radio wave.

DTC Logic

INFOID:0000000003375967

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT-III

Driving at a speed of 40 km/h (25 MPH) or more for 10minutes.

Perform BCM self-diagnosis.

Is DTC “C1724”, “C1725”, “C1726”, “C1727” detected?

YES

>> Proceed to diagnosis procedure. Refer to

WT-29, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003412998

CHECK ID REGISTRATION

With CONSULT-III

Perform the ID registration of all transmitters. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special

Repair Requirement"

Drive at a 40 km/h (25MPH) or more for 10 minutes.

Check all tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.

Can ID registration of all transmitters be completed?

YES

>> GO TO 2.

>> GO TO 4.

CHECK AIR PRESSURE SIGNAL

With CONSULT-III

Start the engine.

Select “DATA MONITOR” mode for “AIR PRESSURE MONITOR” with CONSULT-III.

Read out the value of “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR”, “AIR PRESS RL”.

: Outside

SEIA0768E

DTC

Display item

Malfunction detected condition

Possible case

C1724

[BATT VOLT LOW] FL

Battery voltage of front LH transmitter drops.

• Transmitter malfunction
• Tire pressure receiver mal-

function

• BCM malfunction
• Harness or connector

C1725

[BATT VOLT LOW] FR

Battery voltage of front RH transmitter drops.

C1726

[BATT VOLT LOW] RR

Battery voltage of rear RH transmitter drops.

C1727

[BATT VOLT LOW] RL

Battery voltage of rear LH transmitter drops.

Revision: 2008 October

2009 Murano

WT-30

< COMPONENT DIAGNOSIS >

C1724, C1725, C1726, C1727 TRANSMITTER

Are all tire pressures displayed 0 kPa?

YES

>> GO TO 3.

>> GO TO 5.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

Turn the ignition switch OFF.

Disconnect BCM harness connector and tire pressure receiver harness connector.

Check continuity between BCM harness connector and tire pressure receiver harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace damaged parts.

CHECK TIRE PRESSURE RECEIVER

Check tire pressure receiver. Refer to

WT-36, "Diagnosis Procedure"

Is the inspection result normal?

YES

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts.

>> Replace the tire pressure receiver.

CHECK ID REGISTRATION

Perform ID registration of all transmitters. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special Repair

Requirement"

Can ID registration of all transmitters be completed?

YES

>> GO TO 6.

>> Replace malfunctioning transmitter.

CHECK TIRE PRESSURE MONITORING SYSTEM

With CONSULT-III

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Check all tire pressures with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or more
for several minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

138

139

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Revision: 2008 October

2009 Murano

C1724, C1725, C1726, C1727 TRANSMITTER

WT-31

< COMPONENT DIAGNOSIS >

Is the inspection result normal?

YES

>> INSPECTION END

>> Replace BCM. Refer to

BCS-96, "Removal and Installation"

Special Repair Requirement

INFOID:0000000003375969

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to

WT-111, "Tire Air Pressure"

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

PERFORM ID REGISTRATION

Perform ID registration. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

>> END

Monitored item

Condition

Display value

AIR PRESS FL

Start the engine and drive at 40 km/h (25 MPH) or more
for several minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

WT-32

< COMPONENT DIAGNOSIS >

C1729 VEHICLE SPEED SIGNAL

C1729 VEHICLE SPEED SIGNAL

Description

INFOID:0000000003375970

BCM detects no vehicle speed signal.

DTC Logic

INFOID:0000000003375971

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT-III

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Perform BCM self-diagnosis.

Is DTC “C1729” detected?

YES

>> Proceed to diagnosis procedure. Refer to

WT-32, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375972

CHECK COMBINATION METER SELF-DIAGNOSIS

With CONSULT-III

Perform combination meter self-diagnosis.

Is any DTC detected?

YES

>> Check the DTC.

>> Check combination meter. Refer to

MWI-33, "Diagnosis Description"

Special Repair Requirement

INFOID:0000000003375973

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to

WT-111, "Tire Air Pressure"

Does all tire pressure data meet the specification?

YES

>> GO TO 2.

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

PERFORM ID REGISTRATION

Perform ID registration. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

>> END

DTC

number

Trouble diagnosis name

DTC detecting condition

Possible case

C1729

VHCL SPEED SIG ERR

Vehicle speed signal error.

• CAN communication error
• Combination meter malfunction

Revision: 2008 October

2009 Murano

C1734 BCM

WT-33

< COMPONENT DIAGNOSIS >

C1734 BCM

Description

INFOID:0000000003375974

The BCM (1) reads the air pressure signal received by the tire pres-
sure receiver, and controls the low tire pressure warning lamp and
the buzzer operations. It also has a judgment function to detect a
system malfunction.

DTC Logic

INFOID:0000000003375975

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC REPRODUCTION PROCEDURE

With CONSULT-III

Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.

Perform BCM self-diagnosis with CONSULT-III “DATA MONITOR” within 15 minutes after stopped vehicle.

Is DTC “C1734” detected?

YES

>> Proceed to diagnosis procedure. Refer to

WT-33, "Diagnosis Procedure"

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003375976

CHECK SELF-DIAGNOSTIC RESULTS

With CONSULT-III

On “SELECT DIAG” mode, select the “SELF-DIAG RESULT” screen.

Check display contents in self-diagnostic result.

Does self-diagnostic results indicate any malfunction?

YES

>> Perform trouble diagnosis. Refer to

WT-88, "DTC Index"

>> GO TO 2.

CHECK BCM POWER SUPPLY CIRCUIT

Turn the ignition switch OFF.

Disconnect BCM harness connector.

Check voltage between BCM harness connector terminals and ground.

Is the power supply normal?

YES

>> GO TO 3.

Check the following. If any items are damaged, repair or replace damage parts.

• 40A fusible link [No. L located in the fuse block]. Refer to

PG-102, "Fuse and Fusible Link

Arrangement"

JPEIC0043ZZ

DTC

Display item

Malfunction detected condition

Possible case

C1734

CONTROL UNIT

Tire pressure monitoring system malfunction in BCM.

BCM malfunction

BCM

—

Voltage

Connector

Terminal

M118

Ground

Battery voltage

M119

Revision: 2008 October

2009 Murano

WT-34

< COMPONENT DIAGNOSIS >

C1734 BCM

• 10A fuse [No. 10 located in the fuse block (J/B)]. Refer to

PG-101, "Fuse, Connector and Termi-

nal Arrangement"

• Harness for short or open between battery and BCM harness connector M118 terminal 1.
• Harness for short or open between battery and BCM harness connector M119 terminal 11.
• Check Battery voltage.

CHECK BCM GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair open circuit or short to power in harness or connectors.

CHECK HARNESS BETWEEN BCM AND TIRE PRESSURE RECEIVER

Disconnect tire pressure receiver harness connector.

Check continuity between BCM harness connector and tire pressure receiver harness connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace damaged parts.

CHECK BCM

Check BCM input/output signal. Refer to

WT-46, "Reference Value"

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 6.

CHECK BCM HARNESS CONNECTOR

Check BCM pin terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-96, "Removal and Installation"

>> Repair or replace damaged parts.

Special Repair Requirement

INFOID:0000000003375977

CHECK TIRE AIR PRESSURE

Check all tire air pressures. Refer to

WT-111, "Tire Air Pressure"

Does all tire pressure data meet the specification?

BCM

—

Continuity

Connector

Terminal

M119

Ground

Existed

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

138

139

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

138

139

Revision: 2008 October

2009 Murano

C1734 BCM

WT-35

< COMPONENT DIAGNOSIS >

YES

>> GO TO 2.

>> Inspect or repair the tires or wheels and adjust the tire pressure to the specification.

PERFORM ID REGISTRATION

Perform ID registration. Refer to

WT-5, "ID REGISTRATION PROCEDURE : Special Repair Requirement"

>> END

Revision: 2008 October

2009 Murano

WT-36

< COMPONENT DIAGNOSIS >

TIRE PRESSURE RECEIVER

TIRE PRESSURE RECEIVER

Description

INFOID:0000000003375984

The tire pressure receiver (1) receives the air pressure signal trans-
mitted by the transmitter in each wheel.

Component Function Check

INFOID:0000000003528608

TIRE PRESSURE MONITORING SYSTEM OPERATION

With CONSULT-III

Drive at a speed 40 km/h (25 MPH) or more for 10 minutes.

Check tire pressure with CONSULT-III “DATA MONITOR” within 5 minutes.

Is the inspection result normal?

YES

>> INSPECTION END

NO-1

>> Perform BCM self-diagnosis. Refer to

WT-88, "DTC Index"

NO-2

>> Proceed to diagnosis procedure. Refer to

WT-36, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000003375985

CHECK TIRE PRESSURE RECEIVER SIGNAL

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check tire pressure receiver connector and ground signal with oscilloscope.

JPEIC0042ZZ

Monitored item

Condition

Display value

AIR PRESS FL

Start engine and drive at 40 km/h (25MPH) or
more for 10 minutes.

Approximately equal to the indication on vehicle
information display.

AIR PRESS FR

AIR PRESS RR

AIR PRESS RL

Revision: 2008 October

2009 Murano

TIRE PRESSURE RECEIVER

WT-37

< COMPONENT DIAGNOSIS >

Is the inspection result normal?

YES

>> INSPECTION END

>> GO TO 2.

CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE

Disconnect tire pressure receiver connector.

Check voltage between tire pressure receiver connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Check BCM harness and connector.

CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT

Disconnect BCM harness connector.

Check continuity between BCM harness connector and tire pressure receiver connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace damaged parts.

CHECK BCM CIRCUIT

Inspect the BCM circuit. Refer to

BCS-44, "Diagnosis Procedure"

Is the BCM circuit normal?

YES

>> Replace tire pressure receiver.

Tire pressure receiver

—

Condition

Voltage (Approx.)

Connector

Terminal

M21

Ground

Standby state

When receiving the signal from the trans-
mitter

OCC3881D

OCC3880D

Tire pressure receiver

—

Voltage (Approx.)

Connector

Terminal

M21

Ground

5.0 V

BCM

Tire pressure receiver

Continuity

Connector

Terminal

Connector

Terminal

M123

137

M21

Existed

BCM

—

Continuity

Connector

Terminal

M123

137

Ground

Not existed

Revision: 2008 October

2009 Murano

TIRE PRESSURE WARNING CHECK SWITCH

WT-39

< COMPONENT DIAGNOSIS >

TIRE PRESSURE WARNING CHECK SWITCH

Description

INFOID:0000000003375986

The following item can be checked by grounding the tire pressure
warning check switch harness connector terminal (1).
• The low tire pressure warning lamp in the combination meter blink

according to the self-diagnostic results.

NOTE:
If low tire pressure warning lamp blinks as shown in the figure, the system is normal.
• This mode shows transmitter status is in OFF-mode.

Perform transmitter wake up operation. Refer to

WT-5, "TRANS-

MITTER WAKE UP OPERATION : Special Repair Requirement"

Component Function Check

INFOID:0000000003528663

CHECK LOW TIRE PRESSURE WARNING LAMP OPERATION

Check if low tire pressure warning lamp blinks 1 second and then goes off after turning ignition switch ON.

Is inspection result normal?

YES

>> GO TO 2.

>> Check low tire pressure warning lamp. Refer to

WT-41, "Diagnosis Procedure"

CHECK TIRE PRESSURE WARNING CHECK SWITCH OPERATION

Ground the tire pressure warning check switch harness connector terminal.

Check the low tire pressure warning lamp blinks.

Is the inspection result normal?

YES

>> INSPECTION END

>> Proceed to diagnosis procedure. Refer to

WT-39, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000003375987

CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY CIRCUIT

Turn the ignition switch ON.

CAUTION:

Never start the engine.

Check voltage between tire pressure warning check switch connector and ground.

Is the inspection result normal?

JPEIC0044ZZ

JPEIC0031GB

Tire pressure warning check switch

—

Voltage (Approx.)

Connector

Terminal

M19

Ground

11.8 V

Revision: 2008 October

2009 Murano

WT-40

< COMPONENT DIAGNOSIS >

TIRE PRESSURE WARNING CHECK SWITCH

YES

>> Repair or replace BCM circuit. Replace BCM. Refer to

BCS-96, "Removal and Installation"

>> GO TO 2.

CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT

Turn the ignition switch OFF.

Disconnect BCM harness connector

Check continuity between BCM harness connector and tire pressure warning check switch connector.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace damaged parts.

CHECK BCM

Check BCM input/output signal. Refer to

WT-46, "Reference Value"

Is the inspection result normal?

YES

>> INSPECTION END

>> Check BCM pin terminals for damage or loose connection with harness connector. If any items

are damaged, repair or replace damaged parts. Replace BCM. Refer to

BCS-96, "Removal and

Installation"

BCM

Tire pressure warning check switch

Continuity

Connector

Terminal

Connector

Terminal

Existed

M123

149

M19

BCM

—

Continuity

Connector

Terminal

M123

149

Ground

Not existed

Revision: 2008 October

2009 Murano

LOW TIRE PRESSURE WARNING LAMP

WT-41

< COMPONENT DIAGNOSIS >

LOW TIRE PRESSURE WARNING LAMP

Description

INFOID:0000000003412922

The combination meter receives tire pressure status from the BCM
via CAN communication.
When BCM judges from a transmitter signal that tire pressure is
insufficient, BCM transmits a signal to combination meter via CAN
communication. Combination meter turns on the low tire pressure
warning lamp mounted on the combination meter.

NOTE: Standard air pressure is for 230 kPa (2.3 kg/cm

, 33 psi) vehicles.

Component Function Check

INFOID:0000000003412925

CHECK LOW TIRE PRESSURE WARNING LAMP

Check if low tire pressure warning lamp blinks for 1 second and then goes off after turning the ignition switch
ON.

Is inspection result normal?

YES

>> INSPECTION END

>> Proceed to diagnosis procedure. Refer to

WT-41, "Diagnosis Procedure"

Diagnosis Procedure

INFOID:0000000003412924

CHECK SELF DIAGNOSTIC RESULTS

Perform self-diagnosis of tire pressure monitoring system.
Is inspection result normal?

YES

>> GO TO 2.

>> Check the DTC.

CHECK LOW TIRE PRESSURE WARNING LAMP

Check if low tire pressure warning lamp blinks 1 second and then goes off after turning the ignition switch ON.
Is inspection result normal?

YES

>> INSPECTION END

>> Check combination meter.

SEIA0434E

Condition

Low tire pressure warning lamp

Ignition switch off

OFF

Ignition switch on

Warning lamp turns on for 1second, then turns off.

Less than 182.7 kPa (1.9 kg/cm

, 26 psi) [NOTE]

Tire pressure monitoring system malfunction [Other diagnostic item]

Warning lamp blinks 1 min, then turns on.

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 402