Nissan Murano Z51 (2008 year). Manual - part 262

MIR-8

< FUNCTION DIAGNOSIS >

[WITH ADP]

DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)

MIR CHNG SW–R

“ON/OFF”

×

×

ON/OFF status judged from the door mirror remote control 
switch (switching to right) signal.

MIR CHNG SW–L

“ON/OFF”

×

×

ON/OFF status judged from the door mirror remote control 
switch (switching to left) signal.

TILT SW-UP

“ON/OFF”

×

×

ON/OFF status judged from the tilt switch (up) signal.

TILT SW-DOWN

“ON/OFF”

×

×

ON/OFF status judged from the tilt switch (down) signal.

TELESCO SW-FR

“ON/OFF”

×

×

ON/OFF status judged from the telescoping switch (for-
ward) signal.

TELESCO SW-RR

“ON/OFF”

×

×

ON/OFF status judged from the telescoping switch (back-
ward) signal.

DETENT SW

“ON/OFF”

×

×

The selector lever position “OFF (P position) / ON (other 
than P position)” judged from the detention switch signal.

STARTER SW

“ON/OFF”

×

×

Ignition key switch ON (START, ON) /OFF (ACC, OFF) sta-
tus judged from the ignition switch signal.

SLIDE PULSE

—

–

×

Value (32768) when battery connections are standard. If it 
moves backward, the value increases. If it moves forward, 
the value decreases.

RECLN PULSE

—

–

×

Value (32768) when battery connections are standard. If it 
moves backward, the value increases. If it moves forward, 
the value decreases.

LIFT FR PULSE

—

–

×

Value (32768) when battery connections are standard. If it 
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.

LIFT RR PULSE

—

–

×

Value (32768) when battery connections are standard. If it 
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.

MIR/SEN RH U–D

“V”

–

×

Voltage input from door mirror sensor (passenger side) up/
down is displayed.

MIR/SEN RH R–L

“V”

–

×

Voltage input from door mirror sensor (passenger side) left/
right is displayed.

MIR/SEN LH U–D

“V”

–

×

Voltage input from door mirror sensor (driver side) up/down 
is displayed.

MIR/SEN LH R–L

“V”

–

×

Voltage input from door mirror sensor (driver side) left/right 
is displayed.

TILT PULSE

—

–

×

Value (32768) when battery connections are standard. If it 
moves DOWN, the value increases. If it moves UP, the val-
ue decreases.

TELESCO PULSE

—

–

×

Value (32768) when battery connections are standard. If it 
moves backward, the value increases. If it moves forward, 
the value decreases.

VEHICLE SPEED

—

×

×

Display the vehicle speed signal received from combination 
meter by numerical value [km/h].

P RANG SW CAN

“ON/OFF”

×

×

ON/OFF status judged from the P range switch signal.

R RANGE (CAN)

“ON/OFF”

×

×

ON/OFF status judged from the R range switch signal.

DOOR SW–FL

“ON/OFF”

×

×

ON/OFF status judged from the door switch (front driver 
side) signal.

DOOR SW–FR

“ON/OFF”

×

×

ON/OFF status judged from the door switch (front passen-
ger side) signal.

IGN ON SW

“ON/OFF”

×

×

ON/OFF status judged from the ignition switch signal.

ACC ON SW

“ON/OFF”

×

×

ON/OFF status judged from the ACC switch signal.

KEY ON SW

“ON/OFF”

×

×

ON/OFF status judged from the key on switch signal.

Monitor Item

Unit

Main

Signals

Selection 

From 

Menu

Contents

Revision: 2008 October

2009 Murano

DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)

MIR-9

< FUNCTION DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

ACTIVE TEST

CAUTION:

When driving vehicle, do not perform active test.

WORK SUPPORT

KEYLESS ID

—

×

×

Key ID status judged from the key ID signal.

KYLS DR UNLK

“ON/OFF”

×

×

ON/OFF status judged from the driver side door unlock ac-
tuator output switch signal.

VHCL SPEED (ABS)

“ON/OFF”

×

×

ON/OFF status judged from vehicle speed signal.

HANDLE

“RHD/LHD”

×

×

RHD/LHD status judged from handle position signal.

TRANSMISSION

“AT or CVT/

MT”

×

×

AT or CVT/MT status judged from transmission.

STEERING STATUS

“LOCK/UN-

LOCK”

×

×

LOCK/UNLOCK status judged from steering lock unit.

Monitor Item

Unit

Main

Signals

Selection 

From 

Menu

Contents

Test item

Description

SEAT SLIDE

Activates/deactivates the sliding motor.

SEAT RECLINING

Activates/deactivates the reclining motor.

SEAT LIFTER FR

Activates/deactivates the lifting motor (front).

SEAT LIFTER RR

Activates/deactivates the lifting motor (rear).

TILT MOTOR

Activates/deactivates the tilt motor.

TELESCO MOTOR

Activates/deactivates the telescopic motor.

MIRROR MOTOR RH

Activates/deactivates the mirror motor (passenger side).

MIRROR MOTOR LH

Activates/deactivates the mirror motor (driver side).

MEMORY SW INDCTR

Turns ON/OFF the memory indicator.

Work item

Content

Item

SEAT SLIDE VOLUME SET

The amount of seat sliding for entry/exit assist can be selected 
from 3 items.

40 mm

80 mm

150 mm

EXIT TILT SETTING

Entry/exit assist (steering column) can be selected: 
ON (operated) – OFF (not operated)

ON

OFF

EXIT SEAT SLIDE SETTING

Entry/exit assist (seat) can be selected: 
ON (operated) – OFF (not operated)

ON

OFF

Revision: 2008 October

2009 Murano

MIR-10

< COMPONENT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

COMPONENT DIAGNOSIS

DOOR MIRROR REMOTE CONTROL SWITCH

MIRROR SWITCH

MIRROR SWITCH : Description

INFOID:0000000003554741

It operates angle of the door mirror face.
It transmits mirror face adjust operation to AUTOMATIC DRIVE POSITIONER CONTROL UNIT.

MIRROR SWITCH : Component Function Check

INFOID:0000000003554742

1.

CHECK MIRROR SWITCH FUNCTION

Check the operation on “MIR CON SW–UP/DN” and “MIR CON SW–RH/LH” in “DATA MONITOR” mode
with CONSULT-III.

Is the inspection result normal?

YES

>> Mirror switch function is OK.

NO

>> Refer to 

MIR-10, "MIRROR SWITCH : Diagnosis Procedure"

.

MIRROR SWITCH : Diagnosis Procedure

INFOID:0000000003554743

1.

CHECK MIRROR SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK MIRROR SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.

Monitor item

Condition

MIR CON SW-UP/DN

When operating the mirror switch toward the up or down side.

: ON

Other than above.

: OFF

MIR CON SW-RH/LH

When operating the mirror switch toward the right or left side.

: ON

Other than above.

: OFF

(+)

(–)

Voltage (V)

(Approx.)

Door mirror remote control switch 

Connector

Terminal

D14

4

Ground

5

12

13

15

Revision: 2008 October

2009 Murano

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-11

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to 

ADP-205, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK MIRROR SWITCH

Check door mirror remote control switch (mirror switch).
Refer to 

MIR-11, "MIRROR SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (mirror switch). Refer to 

MIR-66, "Removal and Instal-

lation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-40, "Intermittent Incident"

.

>> INSPECTION END

MIRROR SWITCH : Component Inspection

INFOID:0000000003554744

1.

CHECK MIRROR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit 

Door mirror remote control switch 

Continuity 

Connector

Terminal

Connector

Terminal

M75

3

D14

15

Existed

4

13

15

12

16

4

Automatic drive positioner control unit 

Ground

Continuity 

Connector

Terminal

M75

3

Not existed

4

15

16

Door mirror remote control switch

Ground

Continuity

 Connector

Terminal

D14

7

Existed

Revision: 2008 October

2009 Murano

MIR-12

< COMPONENT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to 

MIR-66, "Removal and Installation"

.

CHANGEOVER SWITCH

CHANGEOVER SWITCH : Description

INFOID:0000000003554745

Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.

CHANGEOVER SWITCH : Component Function Check

INFOID:0000000003554746

1.

CHECK CHANGEOVER SWITCH FUNCTION

Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.

Is the inspection result normal?

YES

>> Changeover switch function is OK.

NO

>> Refer to 

MIR-12, "CHANGEOVER SWITCH : Diagnosis Procedure"

.

CHANGEOVER SWITCH : Diagnosis Procedure

INFOID:0000000003554747

1.

CHECK CHANGEOVER SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK CHANGEOVER SWITCH CIRCUIT

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

4

7

Mirror switch

RIGHT

Existed

Other than above

Not existed

13

LEFT

Existed

Other than above

Not existed

15

UP

Existed

Other than above

Not existed

12

DOWN

Existed

Other than above

Not existed

Monitor item

Condition

MIR CHNG SW-R/L

When operating the changeover toward the right or left side.

: ON

Other than above.

: OFF

(+)

(–)

Voltage (V)

(Approx.)

Door mirror remote control switch

 Connector

Terminal

D14

10

Ground

5

11

Revision: 2008 October

2009 Murano

DOOR MIRROR REMOTE CONTROL SWITCH

MIR-13

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit. Refer to

ADP-205, "Removal and Installation"

 .

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK CHANGEOVER SWITCH

Check door mirror remote control switch (changeover switch).
Refer to 

MIR-13, "CHANGEOVER SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (changeover switch). Refer to 

MIR-66, "Removal and

Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-40, "Intermittent Incident"

.

>> INSPECTION END

CHANGEOVER SWITCH : Component Inspection

INFOID:0000000003554748

1.

CHECK CHANGEOVER SWITCH 

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Automatic drive positioner control unit 

Door mirror remote control switch

Continuity

Connector

Terminal

Connector

Terminal

M75

2

D14

11

Existed

14

10

Automatic drive positioner control unit 

Ground

Continuity

Connector

Terminal

M75

2

Not existed

14

Door mirror remote control switch 

Ground

Continuity

Connector

Terminal

D14

7

Existed

Revision: 2008 October

2009 Murano

MIR-14

< COMPONENT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR REMOTE CONTROL SWITCH

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch. Refer to 

MIR-66, "Removal and Installation"

.

Door mirror remote control switch

Condition

Continuity

Connector

Terminal

D14

10

7

Changeover switch

LEFT

Existed

Other than above

Not existed

11

RIGHT

Existed

Other than above

Not existed

Revision: 2008 October

2009 Murano

DOOR MIRROR

MIR-15

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

DOOR MIRROR

Wiring Diagram - DOOR MIRROR SYSTEM (WITH AUTOMATIC DRIVE POSITION-
ER) -

INFOID:0000000004786413

JCLWM2736GB

Revision: 2008 October

2009 Murano

MIR-16

< COMPONENT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR

JCLWM2737GB

Revision: 2008 October

2009 Murano

DOOR MIRROR

MIR-17

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

JCLWM2738GB

Revision: 2008 October

2009 Murano

MIR-18

< COMPONENT DIAGNOSIS >

[WITH ADP]

DOOR MIRROR

JCLWM2739GB

Revision: 2008 October

2009 Murano

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

MIR-19

< COMPONENT DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

Wiring Diagram - INSIDE MIRROR SYSTEM -

INFOID:0000000003554749

JCLWM2742GB

Revision: 2008 October

2009 Murano

MIR-20

< COMPONENT DIAGNOSIS >

[WITH ADP]

AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM

JCLWM2743GB

Revision: 2008 October

2009 Murano

DRIVER SEAT CONTROL UNIT

MIR-21

< ECU DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

ECU DIAGNOSIS

DRIVER SEAT CONTROL UNIT

Reference Value

INFOID:0000000004786385

VALUES ON THE DIAGNOSIS TOOL

CONSULT-III MONITOR ITEM

Monitor Item

Condition

Value/Status

SET SW

Set switch

Push

ON

Release

OFF

MEMORY SW1

Memory switch 1

Push

ON

Release

OFF

MEMORY SW2

Memory switch 2

Push

ON

Release

OFF

SLIDE SW–FR

Sliding switch (forward)

Operate

ON

Release

OFF

SLIDE SW–RR

Sliding switch (backward)

Operate

ON

Release

OFF

RECLN SW–FR

Reclining switch (forward)

Operate

ON

Release

OFF

RECLN SW–RR

Reclining switch (back-
ward)

Operate

ON

Release

OFF

LIFT FR SW–UP

Lifting switch front (up)

Operate

ON

Release

OFF

LIFT FR SW–DN

Lifting switch front (down)

Operate

ON

Release

OFF

LIFT RR SW–UP

Lifting switch rear (up)

Operate

ON

Release

OFF

LIFT RR SW–DN

Lifting switch rear (down)

Operate

ON

Release

OFF

MIR CON SW–UP

Mirror switch

Up

ON

Other than above

OFF

MIR CON SW–DN

Mirror switch

Down

ON

Other than above

OFF

MIR CON SW–RH

Mirror switch

Right

ON

Other than above

OFF

MIR CON SW–LH

Mirror switch

Left

ON

Other than above

OFF

MIR CHNG SW–R

Changeover switch

Right

ON

Other than above

OFF

MIR CHNG SW–L

Changeover switch

Left

ON

Other than above

OFF

TILT SW-UP

Tilt switch

Upward

ON

Other than above

OFF

TILT SW-DOWN

Tilt switch

Downward

ON

Other than above

OFF

Revision: 2008 October

2009 Murano

MIR-22

< ECU DIAGNOSIS >

[WITH ADP]

DRIVER SEAT CONTROL UNIT

TELESCO SW-FR

Telescopic switch

Forward

ON

Other than above

OFF

TELESCO SW-RR

 Telescopic switch

Backward

ON

Other than above

OFF

DETENT SW

A/T selector lever

P position

OFF

Other than above

ON

STARTER SW

Ignition position

Cranking

ON

Other than above

OFF

SLIDE PULSE

Seat sliding

Forward

The numeral value decreases *

Backward

The numeral value increases*

Other than above

No change to numeral value*

RECLN PULSE

Seat reclining

Forward

The numeral value decreases*

Backward

The numeral value increases 

*

Other than above

No change to numeral value

*

LIFT FR PULSE

Seat lifter (front)

Up

The numeral value decreases 

*

Down

The numeral value increases 

*

Other than above

No change to numeral value

*

LIFT RR PULSE

Seat lifter (rear)

Up

The numeral value decreases 

*

Down

The numeral value increases 

*

Other than above

No change to numeral value

*

MIR/SEN RH U–D

Door mirror (passenger side)

Change between 3.4 (close to peak)

0.6 (close to valley)

MIR/SEN RH R–L

Door mirror (passenger side)

Change between 3.4 (close to left edge)

0.6 (close to right edge)

MIR/SEN LH U–D

Door mirror (driver side)

Change between 3.4 (close to peak)

0.6 (close to valley)

MIR/SEN LH R–L

Door mirror (driver side)

Change between 0.6 (close to left edge)

3.4 (close to right edge)

TILT PULSE

Tilt position

Upward

The numeral value decreases 

*

Downward

The numeral value increases 

*

Other than above

No change to numeral value

*

TELESCO PULSE

Telescopic position

Forward

The numeral value decreases 

*

Backward

The numeral value increases 

*

Other than above

No change to numeral value

*

STEERING STATUS

Steering lock unit

LOCK

LOCK

unlock

UNLOCK

VEHICLE SPEED

The condition of vehicle speed is displayed

km/h

P RANG SW CAN

A/T selector lever

P position

ON

Other than above

OFF

R RANGE (CAN)

A/T selector lever

R position

ON

Other than above

OFF

DOOR SW-FL

Driver door

Open

ON

Close

OFF

Monitor Item

Condition

Value/Status

Revision: 2008 October

2009 Murano

DRIVER SEAT CONTROL UNIT

MIR-23

< ECU DIAGNOSIS >

[WITH ADP]

C

D

E

F

G

H

I

J

K

M

A

B

MIR

N

O

P

*

: The value at the position attained when the battery is connected is regarded as 32768.

TERMINAL LAYOUT

PHYSICAL VALUES

DOOR SW-FR

Passenger door

Open

ON

Close

OFF

IGN ON SW

Ignition switch

ON position

ON

Other than above

OFF

ACC ON SW

Ignition switch

ACC or ON position

ON

Other than above

OFF

KEY ON SW

Intelligent Key

Inserted is key slot

ON

Inserted is not key slot

OFF

KEYLESS ID

UNLOCK button of Intelligent Key is pressed

1,2,3,4or5

KYLS DR UNLK

Intelligent Key or driver 
side door request switch

ON

ON

OFF

OFF

VHCL SPEED (ABS)

Can signal from ABS

Received

ON

Not received

OFF

HANDLE

The BCM for handle position is displayed

LHD

RHD

TRANSMISSION

Transmission type is displayed

AT or CVT

MT

Monitor Item

Condition

Value/Status

JMJIA1689ZZ

Terminal No.

(wire color)

Description

Condition

Voltage (V)

(Approx)

+

-

Signal name

Input/

Output

1

(R)

Ground

Power source 

Input

—

Battery voltage

2

(B)

Ground

Ground (power)

—

—

0

3

(G)

Ground

Sliding motor backward 
output signal

Output

Seat sliding

Operate

(backward)

Battery voltage

Stop

0

4

(G/R)

Ground

Sliding motor forward out-
put signal

Output

Seat sliding

Operate

 (forward)

Battery voltage

Release

0

5

(V)

Ground

Reclining motor backward 
output signal

Output

Seat reclining 

Operate

(backward)

Battery voltage

Stop

0

Revision: 2008 October

2009 Murano