Nissan Murano Z51 (2008 year). Manual

BCM (BODY CONTROL MODULE)

INL-89

< ECU DIAGNOSIS >

INL

Display contents of CONSULT

Fail-safe

Cancellation

B2013: ID DISCORD BCM-S/L

Inhibit engine cranking

Erase DTC

B2014: CHAIN OF S/L-BCM

Inhibit engine cranking

Erase DTC

B2190: NATS ANTENNA AMP

Inhibit engine cranking

Erase DTC

B2191: DIFFERENCE OF KEY

Inhibit engine cranking

Erase DTC

B2192: ID DISCORD BCM-ECM

Inhibit engine cranking

Erase DTC

B2193: CHAIN OF BCM-ECM

Inhibit engine cranking

Erase DTC

B2195: ANTI SCANNING

Inhibit engine cranking

Ignition switch ON

→

OFF

B2557: VEHICLE SPEED

Inhibit steering lock

When normal vehicle speed signals are received from ABS actua-
tor and electric unit (control unit) for 500 ms

B2560: STARTER CONT RELAY

Inhibit engine cranking

500 ms after the following CAN signal communication status be-
comes consistent
• Starter control relay signal
• Starter relay status signal

B2601: SHIFT POSITION

Inhibit steering lock

500 ms after the following signal reception status becomes consis-
tent
• Selector lever P position switch signal
• P range signal (CAN)

B2602: SHIFT POSITION

Inhibit steering lock

5 seconds after the following BCM recognition conditions are ful-
filled
• Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (battery

voltage)

• Vehicle speed: 4 km/h (2.5 MPH) or more

B2603: SHIFT POSI STATUS

Inhibit steering lock

500 ms after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (battery

voltage)

• Selector lever P/N position signal: Except P and N positions (0 V)

B2604: PNP SW

Inhibit steering lock

500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-

age)

- P range signal or N range signal (CAN): ON
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF

B2605: PNP SW

Inhibit steering lock

500 ms after any of the following BCM recognition conditions are
fulfilled
• Ignition switch is in the ON position
- Power position: IGN
- Selector lever P/N position signal: Except P and N positions (0 V)
- Interlock/PNP switch signal (CAN): OFF
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: P or N position (battery volt-

age)

- PNP switch signal (CAN): ON

B2606: S/L RELAY

Inhibit engine cranking

500 ms after the following CAN signal communication status be-
comes consistent
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)

Revision: 2008 October

2009 Murano

INL-90

< ECU DIAGNOSIS >

BCM (BODY CONTROL MODULE)

HIGH FLASHER OPERATION

BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.

FAIL-SAFE CONTROL BY RAIN SENSOR MALFUNCTION

• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-

sor malfunction by rain sensor malfunction signal.

• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO

operation, BCM operates a fail-safe control.

NOTE:
If rain sensor malfunction is detected when ignition switch is turned OFF

⇒

ON and front wiper switch is INT/

AUTO position, BCM operates a fail-safe control.

REAR WIPER MOTOR PROTECTION

BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.

Condition of cancellation

More than 1 minute is passed after the rear wiper stop.

B2607: S/L RELAY

Inhibit engine cranking

500 ms after the following CAN signal communication status be-
comes consistent
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)

B2608: STARTER RELAY

Inhibit engine cranking

500 ms after the following signal communication status becomes
consistent
• Starter motor relay control signal
• Starter relay status signal (CAN)

B2609: S/L STATUS

• Inhibit engine cranking
• Inhibit steering lock

When the following steering lock conditions agree
• BCM steering lock control status
• Steering lock condition No. 1 signal status
• Steering lock condition No. 2 signal status

B260A: IGNITION RELAY

Inhibit engine cranking

500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage)
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)

B260F: ENG STATE SIG LOST

Maintains the power supply
position attained at the time
of DTC detection

When any of the following conditions are fulfilled
• Power position changes to ACC
• Receives engine status signal (CAN)

B2612: S/L STATUS

• Inhibit engine cranking
• Inhibit steering lock

When any of the following conditions are fulfilled
• Steering lock unit status signal (CAN) is received normally
• The BCM steering lock control status matches the steering lock

status recognized by the steering lock unit status signal (CAN
from IPDM E/R)

B2617: STARTER RELAY CIRC

Inhibit engine cranking

1 second after the starter motor relay control inside BCM becomes
normal

B2618: BCM

Inhibit engine cranking

1 second after the ignition relay (IPDM E/R) control inside BCM be-
comes normal

B2619: BCM

Inhibit engine cranking

1 second after the steering lock unit power supply output control in-
side BCM becomes normal

B261E: VEHICLE TYPE

Inhibit engine cranking

BCM initialization

B26E9: S/L STATUS

• Inhibit engine cranking
• Inhibit steering lock

When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
lowing conditions are fulfilled
• Steering condition No. 1 signal: LOCK (0V)
• Steering condition No. 2 signal: LOCK (Battery voltage)

Display contents of CONSULT

Fail-safe

Cancellation

Revision: 2008 October

2009 Murano

BCM (BODY CONTROL MODULE)

INL-91

< ECU DIAGNOSIS >

INL

Turn rear wiper switch OFF.

Operate the rear wiper switch or rear washer switch.

DTC Inspection Priority Chart

INFOID:0000000003729869

If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.

Priority

DTC

B2562: LOW VOLTAGE

• U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)

• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING

• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
• B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG

Revision: 2008 October

2009 Murano

INL-92

< ECU DIAGNOSIS >

BCM (BODY CONTROL MODULE)

DTC Index

INFOID:0000000003729870

NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to

INL-13, "COM-

MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)"

• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
• C1734: CONTROL UNIT

• B2621: INSIDE ANTENNA
• B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA

Priority

DTC

CONSULT display

Fail-safe

Freeze Frame

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key

warning lamp ON

Tire pressure

monitor warning

lamp ON

Reference

page

No DTC is detected.
further testing
may be required.

—

U1000: CAN COMM CIRCUIT

—

BCS-40

U1010: CONTROL UNIT (CAN)

—

BCS-41

U0415: VEHICLE SPEED SIG

—

BCS-42

B2013: ID DISCORD BCM-S/L

—

SEC-55

B2014: CHAIN OF S/L-BCM

—

SEC-56

B2190: NATS ANTENNA AMP

—

SEC-47

B2191: DIFFERENCE OF KEY

—

SEC-50

B2192: ID DISCORD BCM-ECM

—

SEC-51

B2193: CHAIN OF BCM-ECM

—

SEC-53

B2195: ANTI SCANNING

—

SEC-54

B2553: IGNITION RELAY

—

PCS-49

Revision: 2008 October

2009 Murano

BCM (BODY CONTROL MODULE)

INL-93

< ECU DIAGNOSIS >

INL

B2555: STOP LAMP

—

SEC-59

B2556: PUSH-BTN IGN SW

—

SEC-61

B2557: VEHICLE SPEED

—

SEC-63

B2560: STARTER CONT RELAY

—

SEC-64

B2562: LOW VOLTAGE

—

BCS-43

B2601: SHIFT POSITION

—

SEC-65

B2602: SHIFT POSITION

—

SEC-68

B2603: SHIFT POSI STATUS

—

SEC-70

B2604: PNP SW

—

SEC-73

B2605: PNP SW

—

SEC-75

B2606: S/L RELAY

—

SEC-77

B2607: S/L RELAY

—

SEC-78

B2608: STARTER RELAY

—

SEC-80

B2609: S/L STATUS

—

SEC-82

B260A: IGNITION RELAY

—

PCS-51

B260B: STEERING LOCK UNIT

—

SEC-86

B260C: STEERING LOCK UNIT

—

SEC-87

B260D: STEERING LOCK UNIT

—

SEC-88

B260F: ENG STATE SIG LOST

—

SEC-89

B2612: S/L STATUS

—

SEC-92

B2614: ACC RELAY CIRC

—

PCS-53

B2615: BLOWER RELAY CIRC

—

PCS-56

B2616: IGN RELAY CIRC

—

PCS-59

B2617: STARTER RELAY CIRC

—

SEC-96

B2618: BCM

—

PCS-62

B2619: BCM

—

SEC-98

B261A: PUSH-BTN IGN SW

—

SEC-99

B261E: VEHICLE TYPE

(Turn ON for 15

seconds)

—

SEC-102

B2621: INSIDE ANTENNA

—

DLK-95

B2622: INSIDE ANTENNA

—

DLK-97

B2623: INSIDE ANTENNA

—

DLK-99

B26E9: S/L STATUS

(Turn ON for 15

seconds)

—

SEC-90

B26EA: KEY REGISTRATION

—

(Turn ON for 15

seconds)

—

SEC-91

C1704: LOW PRESSURE FL

—

WT-16

C1705: LOW PRESSURE FR

—

C1706: LOW PRESSURE RR

—

C1707: LOW PRESSURE RL

—

CONSULT display

Fail-safe

Freeze Frame

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key

warning lamp ON

Tire pressure

monitor warning

lamp ON

Reference

page

Revision: 2008 October

2009 Murano

INL-94

< ECU DIAGNOSIS >

BCM (BODY CONTROL MODULE)

C1708: [NO DATA] FL

—

WT-18

C1709: [NO DATA] FR

—

C1710: [NO DATA] RR

—

C1711: [NO DATA] RL

—

C1712: [CHECKSUM ERR] FL

—

WT-21

C1713: [CHECKSUM ERR] FR

—

C1714: [CHECKSUM ERR] RR

—

C1715: [CHECKSUM ERR] RL

—

C1716: [PRESSDATA ERR] FL

—

WT-24

C1717: [PRESSDATA ERR] FR

—

C1718: [PRESSDATA ERR] RR

—

C1719: [PRESSDATA ERR] RL

—

C1720: [CODE ERR] FL

—

WT-26

C1721: [CODE ERR] FR

—

C1722: [CODE ERR] RR

—

C1723: [CODE ERR] RL

—

C1724: [BATT VOLT LOW] FL

—

WT-29

C1725: [BATT VOLT LOW] FR

—

C1726: [BATT VOLT LOW] RR

—

C1727: [BATT VOLT LOW] RL

—

C1729: VHCL SPEED SIG ERR

—

WT-32

C1734: CONTROL UNIT

—

WT-33

CONSULT display

Fail-safe

Freeze Frame

Data

•Vehicle Speed

•Odo/Trip Meter

•Vehicle Condi-

tion

Intelligent Key

warning lamp ON

Tire pressure

monitor warning

lamp ON

Reference

page

Revision: 2008 October

2009 Murano

COMBINATION METER

INL-95

< ECU DIAGNOSIS >

INL

COMBINATION METER

Reference Value

INFOID:0000000003728856

VALUES ON THE DIAGNOSIS TOOL

Monitor Item

Condition

Value/Status

SPEED METER
[km/h]

Ignition switch
ON

While driving

Equivalent to speedometer reading
NOTE:
655.35 is displayed when the malfunc-
tion signal is received

SPEED OUTPUT
[km/h]

Ignition switch
ON

While driving

Equivalent to speedometer reading
NOTE:
655.35 is displayed when the malfunc-
tion signal is received

ODO OUTPUT
[km/h or mph]

Ignition switch
ON

—

Equivalent to odometer reading in
combination meter

TACHO METER
[rpm]

Ignition switch
ON

While driving

Equivalent to tachometer reading
NOTE:
8191.875 is displayed when the mal-
function signal is received

FUEL METER
[L]

Ignition switch
ON

—

Values according to fuel level

W TEMP METER
[

Ignition switch
ON

—

Values according to engine coolant
temperature
NOTE:
215 is displayed when the malfunction
signal is input

ABS W/L

Ignition switch
ON

ABS warning lamp ON

ABS warning lamp OFF

Off

VDC/TCS IND

Ignition switch
ON

VDC OFF indicator lamp ON

VDC OFF indicator lamp OFF

Off

SLIP IND

Ignition switch
ON

SLIP Indicator lamp ON

SLIP indicator lamp OFF

Off

BRAKE W/L

Ignition switch
ON

Brake warning lamp ON

Brake warning lamp OFF

Off

DOOR W/L

Ignition switch
ON

Door warning lamp ON

Door warning lamp OFF

Off

HI-BEAM IND

Ignition switch
ON

High-beam indicator lamp ON

High-beam indicator lamp OFF

Off

TURN IND

Ignition switch
ON

Turn signal indicator lamp ON

Turn signal indicator lamp OFF

Off

LIGHT IND

Ignition switch
ON

Light indicator lamp ON

Light indicator lamp OFF

Off

OIL W/L

Ignition switch
ON

Oil pressure warning lamp ON

Oil pressure warning lamp OFF

Off

MIL

Ignition switch
ON

Malfunction indicator lamp ON

Malfunction indicator lamp OFF

Off

CRUISE IND

Ignition switch
ON

CRUISE indicator lamp ON

CRUISE indicator lamp OFF

Off

Revision: 2008 October

2009 Murano

INL-96

< ECU DIAGNOSIS >

COMBINATION METER

O/D OFF IND

Ignition switch
ON

O/D OFF indicator lamp ON

O/D OFF indicator lamp OFF

Off

4WD W/L

Ignition switch
ON

AWD warning lamp ON

AWD warning lamp OFF

Off

4WD LOCK IND

Ignition switch
ON

AWD LOCK indicator lamp ON

AWD LOCK indicator lamp OFF

Off

FUEL W/L

Ignition switch
ON

Low-fuel warning lamp ON

Low-fuel warning lamp OFF

Off

WASHER W/L

Ignition switch
ON

Washer warning displayed

Washer warning not displayed

Off

AIR PRES W/L

Ignition switch
ON

Low tire pressure lamp ON

Low tire pressure lamp OFF

Off

KEY G/Y W/L

Ignition switch
ON

Key warning lamp (green/yellow) ON

Key warning lamp (green/yellow) OFF

Off

LCD

Ignition switch
ON

Engine start information display

B&P I

Ignition switch
ACC

Engine start information display

B&P N

Ignition switch
LOCK

Key ID warning display

ID NG

Ignition switch
LOCK

Steering lock information display

ROTAT

Ignition switch
LOCK

P position warning display

SFT P

Ignition switch
LOCK

Intelligent Key insert information display

INSRT

Ignition switch
LOCK

Intelligent Key low battery warning display

BATT

Ignition switch
ON

Take away warning display

NO KY

Ignition switch
LOCK

Key warning display

OUTKY

Ignition switch
ON

ACC warning display

LK WN

SHIFT IND

Ignition switch
ON

Shift position indicator P display

Shift position indicator R display

Shift position indicator N display

Shift position indicator D display

Shift position indicator L display

O/D OFF SW

Ignition switch
ON

Overdrive control switch ON

Overdrive control switch OFF

Off

M RANGE SW

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

NM RANGE SW

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

Monitor Item

Condition

Value/Status

Revision: 2008 October

2009 Murano

COMBINATION METER

INL-97

< ECU DIAGNOSIS >

INL

NOTE:

Some items are not available according to vehicle specification.

TERMINAL LAYOUT

PHYSICAL VALUES

AT SFT UP SW

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

AT SFT DWN SW

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

ST SFT UP SW

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

ST SFT DWN SW

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

PKB SW

Ignition switch
ON

Parking brake switch ON

Parking brake switch OFF

Off

BUCKLE SW

Ignition switch
ON

Seat belt (driver side) not fastened

Seat belt (driver side) fastened

Off

BRAKE OIL SW

Ignition switch
ON

Brake fluid level switch ON

Brake fluid level switch OFF

Off

DISTANCE
[km]

Ignition switch
ON

—

Possible driving distance calculated by
combination meter

A/C AMP CONN

Ignition switch
ON

Other than the following

Receives ambient sensor power signal

Off

ENTER SW

Ignition switch
ON

When

pressed

Other than the above

Off

SELECT SW

Ignition switch
ON

When

pressed

Other than the above

Off

OUTSIDE TEMP
[

C] or [

Ignition switch
ON

—

Equivalent to ambient temperature
NOTE:
This may not match the indicated value
on the information display.

FUEL LOW SIG

Ignition switch
ON

Low fuel warning displayed

Low fuel warning not displayed

Off

BUZZER

Ignition switch
ON

Buzzer ON

Buzzer OFF

Off

Monitor Item

Condition

Value/Status

JPNIA0968GB

Revision: 2008 October

2009 Murano

INL-98

< ECU DIAGNOSIS >

COMBINATION METER

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

–

Signal name

Input/

Output

(Y)

Ground

Battery power supply

Input

Ignition
switch
OFF

—

Battery voltage

(O)

Ground

IGN signal

Input

Ignition
switch
ON

—

Battery voltage

(B)

Ground

—

Ignition
switch
ON

—

0 V

(SB)

Ground

Illumination control signal

Output

Ignition
switch
ON

• Lighting switch 1ST
• When meter illumination

is maximum

• Lighting switch 1ST
• When meter illumination

is minimum

(SB)

(O)

Trip reset signal

Input

Ignition
switch
ON

When trip reset switch is
pressed.

0 V

Other than the above

5 V

(O)

Ground

Meter control switch ground

—

Ignition
switch
ON

—

0 V

(L)

(O)

Enter switch signal

Input

Ignition
switch
ON

When

pressed.

0 V

Other than the above

5 V

(R)

(O)

Select switch signal

Input

Ignition
switch
ON

When

is pressed.

0 V

Other than the above

5 V

)

(O)

Illumination control switch
signal (+)

Input

Ignition
switch
ON

When

pressed.

0 V

Other than the above

5 V

(GR)

(O)

Illumination control switch
signal (-)

Input

Ignition
switch
ON

When

pressed.

0 V

Other than the above

5 V

(BR)

Ground

Air bag signal

Input

Ignition
switch
ON

Air bag warning lamp
ON

4 V

Air bag warning lamp
OFF

0 V

JPNIA0828GB

JPNIA0827GB

Revision: 2008 October

2009 Murano

COMBINATION METER

INL-99

< ECU DIAGNOSIS >

INL

(L)

Ground

Ambient sensor signal

Input

Ignition
switch
ON

Changes depending to am-
bient temperature.

(P)

Ground

Ambient sensor power

Input

Ignition
switch
ON

—

5 V

(Y)

Ground

Ambient sensor ground

Input

Ignition
switch
ON

—

0 V

(L)

—

CAN-H

—

(P)

—

CAN-L

—

(B)

Ground

—

Ignition
switch
ON

—

0 V

(W)

Ground

Fuel level sensor signal
ground

—

Ignition
switch
ON

—

0 V

(BR)

Ground

Alternator signal

Input

Ignition
switch
ON

Charge warning lamp ON

2 V

Charge warning lamp OFF

12 V

(G)

Ground

Parking brake switch signal

Input

Ignition
switch
ON

Parking brake ON

0 V

Parking brake OFF

5 V

(V)

Ground

Brake fluid level switch sig-
nal

Input

Ignition
switch
ON

Brake fluid level is normal

12 V

Brake fluid level is less than
LOW level

0 V

(R)

Ground

Washer level switch signal

Input

Ignition
switch
ON

Washer level switch ON

0 V

Washer level switch OFF

5 V

(P)

Ground

Vehicle speed signal output
(2-pulse)

Output

Ignition
switch
ON

Speedometer operated
[When vehicle speed is ap-
prox. 40 km/h (25 MPH)]

NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

–

Signal name

Input/

Output

JSNIA0014GB

JSNIA0015GB

Revision: 2008 October

2009 Murano

INL-100

< ECU DIAGNOSIS >

COMBINATION METER

*1: Without automatic drive positioner

*2: With automatic drive positioner

Wiring Diagram - METER -

INFOID:0000000003728857

NOTE:
• Type A Up to VIN: JN8AZ18U*9W100000, JN8AZ18W*9W200000 (EXCEPT FOR MEXICO),

JN8AZ18U*9W710000, JN8AZ18W*9W810000 (FOR MEXICO)

(V)

Ground

Vehicle speed signal output
(8-pulse)

Output

Ignition
switch
ON

Speedometer operated
[When vehicle speed is ap-
prox. 40 km/h (25 MPH)]

NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).

(LG)

Ground

Overdrive control switch
signal

Input

Ignition
switch
ON

Overdrive control switch
pressed.

0 V

Overdrive control switch
not pressed.

12 V

(G)

Ground

Fuel level sensor signal

Input

Ignition
switch
ON

—

(SB)

Ground

Seat belt buckle switch sig-
nal (driver side)

Input

Ignition
switch
ON

When driver seat belt is fas-
tened.

12 V

When driver seat belt is un-
fastened.

0 V

(R)

Ground

Seat belt buckle switch sig-
nal (passenger side)

Input

Ignition
switch
ON

• When getting in the pas-

senger seat.

• When passenger seat

belt is fastened.

12 V

• When getting in the pas-

senger seat.

• When passenger seat

belt is unfastened.

0 V

Terminal No.

(Wire color)

Description

Condition

Value

(Approx.)

–

Signal name

Input/

Output

JSNIA0012GB

JPNIA0740ZZ

Revision: 2008 October

2009 Murano

Nissan Murano Z51 (2008 year). Manual - part 241