Nissan Murano Z51 (2008 year). Manual - part 109

>> GO TO 1.

Revision: 2008 October

2009 Murano

DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY

DLK-277

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY

Description

INFOID:0000000003318147

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-270, "ALL DOOR : Diagnosis Procedure"

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent key is removed from key slot.
• All doors are closed.

Diagnosis Procedure

INFOID:0000000003318148

CHECK POWER DOOR LOCK OPERATION

Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?

YES

>> GO TO 2.

>> Go to

CHECK REMOTE KEYLESS ENTRY RECEIVER

Check remote keyless entry receiver.
Refer to

DLK-120, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK INTELLIGENT KEY

Check Intelligent Key.
Refer to

DLK-135, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK KEY SLOT

Check key slot.
Refer to

DLK-137, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DLK-278

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SELECTIVE UNLOCK FUNCTION DOES NOT OPERATE WITH INTELLIGENT

KEY

SELECTIVE UNLOCK FUNCTION DOES NOT OPERATE WITH INTELLI-
GENT KEY

Description

INFOID:0000000003318151

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-270, "ALL DOOR : Diagnosis Procedure"

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent key is removed from key slot.
• All doors are closed.

Diagnosis Procedure

INFOID:0000000003318152

CHECK POWER DOOR LOCK OPERATION

Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?

YES

>> GO TO 2.

>> Go to

CHECK “DOOR LOCK–UNLOCK SET” SETTING IN “WORK SUPPORT”

Check “DOOR LOCK-UNLOCK SET” setting in “WORK SUPPORT”.
Refer to

DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “DOOR LOCK-UNLOCK SET” of “WORK SUPPORT”.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

POWER WINDOW DOWN FUNCTION DOES NOT WORK WHEN OPERATING

WITH INTELLIGENT KEY

DLK-279

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

POWER WINDOW DOWN FUNCTION DOES NOT WORK WHEN OPERAT-
ING WITH INTELLIGENT KEY

Description

INFOID:0000000003318153

NOTE:
• Before performing the diagnosis in the following procedure, check “ Work Flow”. Refer to

Diagnosis Procedure

INFOID:0000000003318154

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function.

Does door lock/unlock with Intelligent key button?

YES

>> GO TO 2.

>> Go to

PWC-100, "Diagnosis Procedure"

CHECK POWER WINDOW OPERATION

Check power window operation.
Does power window up/down with power window main switch?

YES

>> GO TO 3.

>> Go to

CHECK “PW DOWN SET” SETTING IN “WORK SUPPORT”

Check “PW DOWN SET” setting in “WORK SUPPORT”.
Refer to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

Is the inspection result normal?

YES

>> GO TO 4.

>> Set “PW DOWN SET” setting in “WORK SUPPORT”.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DLK-280

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

PANIC ALARM FUNCTION DOES NOT OPERATE

PANIC ALARM FUNCTION DOES NOT OPERATE

Description

INFOID:0000000003318155

NOTE:
• Before performing the diagnosis following procedure, check “Work Flow”. Refer to

DLK-14, "Work Flow"

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATION CONDITIONS)

• Ignition switch is in OFF or LOCK position.
• Intelligent Key is removed from key slot.

Diagnosis Procedure

INFOID:0000000003318156

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function.

Does door lock/unlock with Intelligent key button?

YES

>> GO TO 2.

>> Go to

CHECK VEHICLE SECURITY ALARM OPERATION

Check vehicle security alarm operation.

Does alarm (headlamp and horn) active?

YES

>> GO TO 3.

>> Go to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

CHECK “PANIC ALARM SET” SETTING IN “WORK SUPPORT”

Check “PANIC ALARM SET” setting in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 4.

>> Set “PANIC ALARM SET” setting in “WORK SUPPORT”.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

>> GO TO 1.

Revision: 2008 October

2009 Murano

HAZARD AND HORN REMINDER DOES NOT OPERATE

DLK-281

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

HAZARD AND HORN REMINDER DOES NOT OPERATE

Description

INFOID:0000000003625925

NOTE:
• Before performing the diagnosis following procedure, check “Work Flow”. Refer to

DLK-14, "Work Flow"

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATION CONDITIONS)

• Ignition switch is in OFF or LOCK position.
• Intelligent Key is removed from key slot.

Diagnosis Procedure

INFOID:0000000003625926

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

Check “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.

CHECK “HORN WITH KEYLESS LOCK” SETTING IN “WORK SUPPORT”.

Check “HORN WITH KEYLESS LOCK” setting in “WORK SUPPORT”.
Refer to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “HORN WITH KEYLESS LOCK” setting in “WORK SUPPORT”.

CHECK HAZARD WARNING LAMP

Check hazard warning lamp.
Refer to

DLK-146, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK HORN

Check horn.
Refer to

DLK-141, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DLK-282

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

AUTO DOOR LOCK OPERATION DOES NOT OPERATE

AUTO DOOR LOCK OPERATION DOES NOT OPERATE

Description

INFOID:0000000003318167

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

Diagnosis Procedure

INFOID:0000000003318168

CHECK “AUTO LOCK SET” SETTING IN “WORK SUPPORT”

Check “AUTO LOCK SET” setting in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “AUTO LOCK SET” setting in “WORK SUPPORT”.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH

DLK-283

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH

DRIVER SIDE

DRIVER SIDE : Description

INFOID:0000000003318157

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent Key is removed from key slot.
• Ignition switch is in OFF position.
• No Intelligent Keys are inside the vehicle.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000003318158

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function.
Does door lock/unlock with Intelligent key button?

YES

>> GO TO 2.

>> Go to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”

Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.

CHECK DOOR REQUEST SWITCH

Check door request switch (driver side).
Refer to

DLK-125, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK OUTSIDE KEY ANTENNA

Check outside key antenna (driver side).
Refer to

DLK-131, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check Intermittent Incident. Refer to

>> GO TO 1.

PASSENGER SIDE

PASSENGER SIDE : Description

INFOID:0000000003318159

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

Revision: 2008 October

2009 Murano

DLK-284

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent Key is removed from key slot.
• Ignition switch is in OFF position.
• No Intelligent Keys are inside the vehicle.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000003318160

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function.
Does door lock/unlock with Intelligent key button?

YES

>> GO TO 2.

>> Go to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”

Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.

CHECK DOOR REQUEST SWITCH

Check door request switch (passenger side).
Refer to

DLK-125, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK OUTSIDE KEY ANTENNA

Check outside key antenna (passenger side).
Refer to

DLK-131, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check Intermittent Incident. Refer to

>> GO TO 1.

BACK DOOR

BACK DOOR : Description

INFOID:0000000003625912

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent Key is removed from key slot.
• Ignition switch is in OFF position.
• No Intelligent Keys are inside the vehicle.

Revision: 2008 October

2009 Murano

DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH

DLK-285

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

BACK DOOR : Diagnosis Procedure

INFOID:0000000003625913

CHECK REMOTE KEYLESS ENTRY FUNCTION

Check remote keyless entry function.

Does door lock/unlock with Intelligent key button?

YES

>> GO TO 2.

>> Go to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”

Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.

CHECK DOOR REQUEST SWITCH

Check door request switch (back door).
Refer to

DLK-125, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK OUTSIDE KEY ANTENNA

Check outside key antenna (rear bumper).
Refer to

DLK-131, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check Intermittent Incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DLK-286

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

SELECTIVE UNLOCK FUNCTION DOES NOT OPERATE WITH DOOR REQUEST

SWITCH

SELECTIVE UNLOCK FUNCTION DOES NOT OPERATE WITH DOOR RE-
QUEST SWITCH

Description

INFOID:0000000003318163

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-283, "DRIVER SIDE : Description"

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent Key is removed from key slot.
• Ignition switch is in OFF position.
• No Intelligent Keys are inside the vehicle.

Diagnosis Procedure

INFOID:0000000003318164

CHECK DOOR LOCK FUNCTION

Check door lock function by door request switch.

Does door lock/unlock with door request switch?

YES

>> GO TO 2.

>> • Go to

(driver side).

• Go to

DLK-283, "PASSENGER SIDE : Description"

(passenger side).

• Go to

DLK-284, "BACK DOOR : Description"

(back door).

CHECK “DOOR LOCK–UNLOCK SET” SETTING IN “WORK SUPPORT”

Check “DOOR LOCK-UNLOCK SET” setting in “WORK SUPPORT”.
Refer to

DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

DLK-287

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

Description

INFOID:0000000003625927

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"

• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and

check each symptom.

CONDITIONS OF VEHICLE (OPERATING CONDITIONS)

• Intelligent Key is removed from key slot.
• Ignition switch is in OFF position.
• No Intelligent Keys are inside the vehicle.

Diagnosis Procedure

INFOID:0000000003625928

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

Check “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “HAZARD ANSWER BACK” in “WORK SUPPORT”.

CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”

Check “ANS BACK I-KEY LOCK” setting in “WORK SUPPORT”.
Refer to

DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"

Is the inspection result normal?

YES

>> GO TO 3.

>> Set “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.

CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”

Check “ANS BACK I-KEY UNLOCK” setting in “WORK SUPPORT”.
Refer to

DLK-59, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"

Is the inspection result normal?

YES

>> GO TO 4.

>> Set “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.

CHECK HAZARD WARNING LAMP

Check hazard warning lamp.
Refer to

DLK-146, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to

DLK-133, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 6.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DLK-288

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

KEY REMINDER FUNCTION DOES NOT OPERATE

KEY REMINDER FUNCTION DOES NOT OPERATE

Description

INFOID:0000000003318165

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-39, "KEY REMINDER FUNCTION : System

• Understand the operation when does it work, refer to

DLK-61, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"

Diagnosis Procedure

INFOID:0000000003318166

CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”

Check “ANTI KEY LOCK IN FUNCTI” setting in “WORK SUPPORT”.
Refer to

Is the inspection result normal?

YES

>> GO TO 2.

>> Set “ANTI KEY LOCK IN FUNCTI” setting in “WORK SUPPORT”.

CHECK DOOR SWITCH

Check door switch.
Refer to

DLK-103, "WITH AUTOMATIC BACK DOOR : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
Refer to

(console).

(luggage room).

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK UNLOCK SENSOR

Check unlock sensor.
Refer to

DLK-129, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

KEY WARNING DOES NOT OPERATE

DLK-289

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

KEY WARNING DOES NOT OPERATE

Description

INFOID:0000000003318169

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-41, "WARNING FUNCTION : System

• Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm

the list above twice in order to ensure proper operation. Refer to

DLK-144, "Component Function Check"

• Door lock function is normal.

Diagnosis Procedure

INFOID:0000000003318170

CHECK BUZZER (COMBINATION METER)

Check buzzer (combination meter).
Refer to

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK DOOR SWITCH

Check door switch (driver side).
Refer to

DLK-103, "WITH AUTOMATIC BACK DOOR : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK KEY SLOT

Check key slot.
Refer to

DLK-137, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK COMBINATION METER DISPLAY

Check combination meter display.
Refer to

DLK-143, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CHECK KEY SLOT ILLUMINATION

Check key slot illumination.
Refer to

DLK-139, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 6.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

DLK-290

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

OFF POSITION WARNING DOES NOT OPERATE

OFF POSITION WARNING DOES NOT OPERATE

Description

INFOID:0000000003318173

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-41, "WARNING FUNCTION : System

• Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm

the list above twice in order to ensure proper operation. Refer to

DLK-144, "Component Function Check"

• Door lock function is normal.

Diagnosis Procedure

INFOID:0000000003318174

CHECK POWER POSITION

Check if ignition switch position is changing or not.

Does ignition switch position change?

YES

>> GO TO 2.

>> Check DTC for BCM. Refer to

DLK-255, "DTC Index"

CHECK BUZZER (COMBINATION METER)

Check buzzer (combination meter).
Refer to

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to

DLK-133, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 4.

>> Repair or replace the malfunctioning parts.

CHECK DOOR SWITCH

Check door switch (driver side).
Refer to

DLK-103, "WITH AUTOMATIC BACK DOOR : Component Function Check"

Is the inspection result normal?

YES

>> GO TO 5.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the result normal?

YES

>> Check intermittent incident. Refer to

>> GO TO 1.

Revision: 2008 October

2009 Murano

P POSITION WARNING DOES NOT OPERATE

DLK-291

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DLK

P POSITION WARNING DOES NOT OPERATE

Description

INFOID:0000000003318177

NOTE:
• Before performing the diagnosis in the following procedure, check “Work Flow”. Refer to

DLK-41, "WARNING FUNCTION : System

• Warning functions operating condition is extremely complicated, during operating confirmations, reconfirm

the list above twice in order to ensure proper operation. Refer to