Nissan Qashqai J11. Manual - part 917

PB-50

< BASIC INSPECTION >

ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION

ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION

Description

INFOID:0000000010833863

CAUTION:

When performing the following operations, always use CONSULT, for performing “INITIALIZATION
POSITION ADJUSTMENT”, “BRAKE OPERATION” and “BRAKE RELEASE” of “WORK SUPPORT”.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833864

CAUTION:

When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Replacing rear brake caliper assembly

1.

PERFORM INITIALIZATION POSITION ADJUSTMENT

With CONSULT

1.

Turn the ignition switch OFF to ON.

2.

Select “EHS/PKB”, “WORK SUPPORT”, and “INITIALIZATION POSITION ADJUSTMENT” according to
this order.

CAUTION:

• Never operate the parking brake switch.
• Never depress the brake pedal.

3.

Touch “START”.

>> GO TO 2.

2.

PERFORM BRAKE OPERATION

With CONSULT

1.

Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.

CAUTION:

• Never operate the parking brake switch.
• Never depress the brake pedal.

2.

Touch “START”.

Procedure

• INITIALIZATION POSITION ADJUSTMENT
• BRAKE OPERATION
• BRAKE RELEASE

Removing/installing electric parking brake control module

—

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

×

Replacing rear brake pad

×

Removing/installing rear brake caliper assembly

—

Replacing rear brake caliper assembly

×

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

—

Replacing clutch stroke sensor

—

Removing/installing clutch pedal

—

Replacing clutch pedal

—

CALIBRATION OF G SENSOR

PB-51

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

CALIBRATION OF G SENSOR

Description

INFOID:0000000010833865

CAUTION:

When performing the following operations, always use CONSULT, for performing “G SENSOR CALI-
BRATION” of “WORK SUPPORT”.
NOTE:
G sensor is integrated in electric parking control module.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833866

CAUTION:

When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module (G sensor is integrated in electric parking brake

control module)

1.

CHECK THE VEHICLE STATUS

1.

Steer the steering wheel to the straight-ahead position.

2.

Stop the vehicle on level surface.

3.

Stop the engine.

4.

Turn the ignition switch OFF.

Is the vehicle stopped with steering wheel in the straight-ahead on level surface?

YES

>> GO TO 2.

NO

>> Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

2.

PERFORM G SENSOR CALIBRATION

CAUTION:

• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Select “EHS/PKB”, “WORK SUPPORT”, and “G SENSOR CALIBRATION” according to this order.

3.

Touch “START”.

4.

After approx. 10 seconds, touch “END”.

5.

Turn the ignition switch OFF and then turn it ON again.

Procedure

G SENSOR CALIBRATION

Removing/installing electric parking brake control module

×

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

—

Replacing rear brake pad

—

Removing/installing rear brake caliper assembly

—

Replacing rear brake caliper assembly

—

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

—

Replacing clutch stroke sensor

—

Removing/installing clutch pedal

—

Replacing clutch pedal

—

PB-52

< BASIC INSPECTION >

CALIBRATION OF G SENSOR

CALIBRATION OF G SENSOR

Description

INFOID:0000000010833865

CAUTION:

When performing the following operations, always use CONSULT, for performing “G SENSOR CALI-
BRATION” of “WORK SUPPORT”.
NOTE:
G sensor is integrated in electric parking control module.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833866

CAUTION:

When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module (G sensor is integrated in electric parking brake

control module)

1.

CHECK THE VEHICLE STATUS

1.

Steer the steering wheel to the straight-ahead position.

2.

Stop the vehicle on level surface.

3.

Stop the engine.

4.

Turn the ignition switch OFF.

Is the vehicle stopped with steering wheel in the straight-ahead on level surface?

YES

>> GO TO 2.

NO

>> Steer the steering wheel to the straight-ahead position. Stop the vehicle on level surface.

2.

PERFORM G SENSOR CALIBRATION

CAUTION:

• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.

With CONSULT

1.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

2.

Select “EHS/PKB”, “WORK SUPPORT”, and “G SENSOR CALIBRATION” according to this order.

3.

Touch “START”.

4.

After approx. 10 seconds, touch “END”.

5.

Turn the ignition switch OFF and then turn it ON again.

Procedure

G SENSOR CALIBRATION

Removing/installing electric parking brake control module

×

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

—

Replacing rear brake pad

—

Removing/installing rear brake caliper assembly

—

Replacing rear brake caliper assembly

—

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

—

Replacing clutch stroke sensor

—

Removing/installing clutch pedal

—

Replacing clutch pedal

—

RESET OF CLUTCH STROKE SENSOR

PB-53

< BASIC INSPECTION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

RESET OF CLUTCH STROKE SENSOR

Description

INFOID:0000000010833867

CAUTION:

When the following operations are performed, always use CONSULT, and carry “CLUTCH SENSOR
RESET” of “WORK SUPPORT”.

×

: Required

 —: not required

Work Procedure

INFOID:0000000010833868

CAUTION:

When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.) 
• Replacing electric parking brake control module
• Removing/installing clutch stroke sensor
• Replacing clutch stroke sensor
• Removing/installing clutch pedal
• Replacing clutch pedal

1.

CHECK THE VEHICLE STATUS

1.

Stop the vehicle.

2.

Stop the engine.

3.

Turn the ignition switch OFF.

>> GO TO 2.

2.

CHECKING INSTALLATION CONDITION OF CLUTCH COMPONENTS

Check the installation conditions of clutch components.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace error-detected parts and GO TO 3.

3.

PERFORM CLUTCH SENSOR RESET

CAUTION:

• Never allow passenger or load on the vehicle.
• Never apply vibration to the vehicle body when opening or closing door during calibration.

With CONSULT

1.

Turn the ignition switch ON.

Procedure

CLUTCH SENSOR RESET

Removing/installing electric parking brake control module

—

Replacing electric parking brake control module

×

Removing/installing rear brake pad (When not pressing piston of rear 
brake caliper assembly)

—

Removing/installing rear brake pad (When pressing piston of rear brake 
caliper assembly)

—

Replacing rear brake pad

—

Removing/installing rear brake caliper assembly

—

Replacing rear brake caliper assembly

—

Removing/installing parking brake switch

—

Replacing parking brake switch

—

Removing/installing clutch stroke sensor

×

Replacing clutch stroke sensor

×

Removing/installing clutch pedal

×

Replacing clutch pedal

×