Nissan Juke (2014 year). Service Repair Manual - part 55

BACK DOOR DOES NOT OPENED

DLK-105

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

BACK DOOR DOES NOT OPENED

Diagnosis Procedure

INFOID:0000000009754025

1.

CHECK BACK DOOR OPENER SWITCH

Check back door opener switch.
Refer to 

DLK-63, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK BACK DOOR OPENER ACTUATOR

Check back door opener actuator.
Refer to 

DLK-63, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK VEHICLE SPEED SIGNAL

Check vehicle speed signal.
Refer to 

MWI-32, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-106

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

AUTO DOOR LOCK OPERATION DOES NOT OPERATE

AUTO DOOR LOCK OPERATION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754026

1.

CHECK “AUTO LOCK SET” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “AUTO LOCK SET” in “WORK SUPPORT” mode.

3.

Check “AUTO LOCK SET” in “WORK SUPPORT”.
Refer to 

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “AUTO LOCK SET” setting in “WORK SUPPORT”.

2.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPERATE

DLK-107

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPER-
ATE

Diagnosis Procedure

INFOID:0000000009754027

1.

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

2.

CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.

3.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-108

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754028

1.

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

2.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

3.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-

ATE

DLK-109

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE

Diagnosis Procedure

INFOID:0000000009754029

1.

CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.

2.

CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.

3.

CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”

1.

Select “DOOR LOCK” of “BCM” using CONSULT.

2.

Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.

3.

Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
Refer to 

DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.

4.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-110

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754030

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-59, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-32, "DTC Index"

. (Combination meter)

2.

CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.

3.

Check the “HAZARD ANSWER BACK” in “WORK SUPPORT”.
Refer to 

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “HAZARD ANSWER BACK” in “WORK SUPPORT”.

3.

CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.

3.

Check the “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.
Refer to 

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Set “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.

4.

CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.

3.

Check the “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.
Refer to 

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Set “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.

5.

CHECK HAZARD FUNCTION

Check hazard function.
Refer to 

DLK-84, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-86, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

Revision: 2013 October

2014 JUKE

HAZARD AND BUZZER REMINDER DOES NOT OPERATE

DLK-111

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-112

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

KEY REMINDER FUNCTION DOES NOT OPERATE

KEY REMINDER FUNCTION DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754031

1.

CHECK DTC WITH BCM

Check that DTC is not detected with BCM.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Refer to 

BCS-59, "DTC Index"

.

2.

CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2.

Select “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT” mode.

3.

Check “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT”.
Refer to 

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT”.

3.

CHECK DOOR SWITCH

Check door switch.
Refer to 

DLK-81, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Instrument center: Refer to 

DLK-51, "DTC Logic"

.

• Console: Refer to 

DLK-53, "DTC Logic"

.

• Luggage room: Refer to 

DLK-55, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK UNLOCK SENSOR

Check unlock sensor.
Refer to 

DLK-92, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement. 

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

OFF POSITION WARNING DOES NOT OPERATE

DLK-113

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

OFF POSITION WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754032

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-59, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-32, "DTC Index"

. (Combination meter)

2.

CHECK DOOR SWITCH

Check front door switch (driver side).
Refer to 

DLK-81, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK COMBINATION METER BUZZER

Check combination meter buzzer.
Refer to 

WCS-40, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-86, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-114

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

P POSITION WARNING DOES NOT OPERATE

P POSITION WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754033

1.

CHECK DTC WITH BCM, TCM AND COMBINATION METER

Check that DTC is not detected with BCM, TCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-59, "DTC Index"

. (BCM)

NO-2

>> Refer to 

TM-198, "DTC Index"

. (TCM)

NO-3

>> Refer to 

MWI-32, "DTC Index"

. (Combination meter)

2.

CHECK COMBINATION METER BUZZER

Check combination meter buzzer.
Refer to 

WCS-40, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-86, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK DOOR SWITCH

Check front door switch (driver side).
Refer to 

DLK-81, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Instrument center: Refer to 

DLK-51, "DTC Logic"

.

• Console: Refer to 

DLK-53, "DTC Logic"

.

• Luggage room: Refer to 

DLK-55, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK KEY WARNING LAMP

Check key warning lamp.
Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

ACC WARNING DOES NOT OPERATE

DLK-115

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

ACC WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754034

1.

CHECK COMBINATION METER BUZZER

Check combination meter buzzer.
Refer to 

WCS-40, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-116

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

TAKE AWAY WARNING DOES NOT OPERATE

TAKE AWAY WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754035

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-59, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-32, "DTC Index"

. (Combination meter)

2.

CHECK COMBINATION METER BUZZER

Check combination meter buzzer.
Refer to 

WCS-40, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK KEY WARNING LAMP

Check key warning lamp.
Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK DOOR SWITCH

Check door switch.
Refer to 

DLK-81, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-86, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Instrument center: Refer to 

DLK-51, "DTC Logic"

.

• Console: Refer to 

DLK-53, "DTC Logic"

.

• Luggage room: Refer to 

DLK-55, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

INTELLIGENT KEY LOW BATTERY WARNING DOES NOT OPERATE

DLK-117

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INTELLIGENT KEY LOW BATTERY WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754036

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-59, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-32, "DTC Index"

. (Combination meter)

2.

CHECK “LO- BATT OF KEY FOB WARN” SETTING IN “WORK SUPPORT”

1.

Select “INTELLIGENT KEY” of “BCM”.

2.

Select “LO- BATT OF KEY FOB WARN” in “WORK SUPPORT” mode.

3.

Check “LO- BATT OF KEY FOB WARN” in “WORK SUPPORT”.
Refer to 

DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Set “LO- BATT OF KEY FOB WARN” in “WORK SUPPORT”.

3.

CHECK KEY WARNING LAMP

Check key warning lamp.
Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK INTELLIGENT KEY BATTERY

Check Intelligent Key battery.
Refer to 

DLK-85, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Instrument center: Refer to 

DLK-51, "DTC Logic"

.

• Console: Refer to 

DLK-53, "DTC Logic"

.

• Luggage room: Refer to 

DLK-55, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-118

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DOOR LOCK OPERATION WARNING DOES NOT OPERATE

DOOR LOCK OPERATION WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754037

1.

CHECK DOOR LOCK FUNCTION

Check door lock function.
Does door lock/unlock using door request switch?

YES

>> GO TO 2.

NO

>> Refer to 

DLK-79, "Component Function Check"

.

2.

CHECK INTELLIGENT KEY WARNING BUZZER

Check Intelligent Key warning buzzer.
Refer to 

DLK-86, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

KEY ID WARNING DOES NOT OPERATE

DLK-119

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

KEY ID WARNING DOES NOT OPERATE

Diagnosis Procedure

INFOID:0000000009754038

1.

CHECK DTC WITH BCM AND COMBINATION METER

Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?

YES

>> GO TO 2.

NO-1

>> Refer to 

BCS-59, "DTC Index"

. (BCM)

NO-2

>> Refer to 

MWI-32, "DTC Index"

. (Combination meter)

2.

CHECK INTELLIGENT KEY BATTERY

Check Intelligent Key battery.
Refer to 

DLK-85, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK INSIDE KEY ANTENNA

Check inside key antenna.
• Instrument center: Refer to 

DLK-51, "DTC Logic"

.

• Console: Refer to 

DLK-53, "DTC Logic"

.

• Luggage room: Refer to 

DLK-55, "DTC Logic"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK KEY WARNING LAMP

Check key warning lamp.
Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE

DLK-120

< SYMPTOM DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

KEY WARNING LAMP DOES NOT ILLUMINATE

KEY WARNING LAMP DOES NOT ILLUMINATE

Diagnosis Procedure

INFOID:0000000009754039

1.

CHECK KEY WARNING LAMP 

Check key warning lamp.
Refer to 

DLK-88, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

REPLACE BCM

1.

Replace BCM. Refer to 

BCS-90, "Removal and Installation"

.

2.

Confirm the operation after replacement.

Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-46, "Intermittent Incident"

.

Revision: 2013 October

2014 JUKE