Nissan Juke (2014 year). Service Repair Manual

DEF-42

< SYMPTOM DIAGNOSIS >

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR MIRROR

DEFOGGERS OPERATE

REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH DOOR
MIRROR DEFOGGERS OPERATE

Diagnosis Procedure

INFOID:0000000009754282

CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to

DEF-28, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

>> GO TO 1.

Revision: 2013 October

2014 JUKE

DOOR MIRROR DEFOGGER DOES NOT OPERATE

DEF-43

< SYMPTOM DIAGNOSIS >

DEF

DOOR MIRROR DEFOGGER DOES NOT OPERATE

BOTH SIDES

BOTH SIDES : Description

INFOID:0000000009754283

Both door mirror defoggers do not operate.

BOTH SIDES : Diagnosis Procedure

INFOID:0000000009754284

CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to

DEF-28, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CHECK DOOR MIRROR DEFOGGER

Check door mirror defogger.
Refer to

DEF-31, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 3.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

>> GO TO 1.

DRIVER SIDE

DRIVER SIDE : Description

INFOID:0000000009754285

Driver side door mirror defogger does not operate but passenger side door mirror defogger operates.

DRIVER SIDE : Diagnosis Procedure

INFOID:0000000009754286

CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check driver side door mirror defogger.
Refer to

DEF-31, "Component Function Check"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

>> GO TO 1.

PASSENGER SIDE

PASSENGER SIDE : Description

INFOID:0000000009754287

Passenger side door mirror defogger does not operate but driver side door mirror defogger operates.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000009754288

CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER.

Revision: 2013 October

2014 JUKE

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER

SWITCH BUT IT IS OPERATED

DEF-45

< SYMPTOM DIAGNOSIS >

DEF

ON IS NOT DISPLAYED WHEN PRESSING REAR WINDOW DEFOGGER
SWITCH BUT IT IS OPERATED

Diagnosis Procedure

INFOID:0000000009754289

CHECK MULTI DISPLAY UNIT FUNCTION

Check that the multi display unit is operating normally.
Refer to

HAC-42, "Work Flow"

Is the inspection result normal?

YES

>> GO TO 2.

>> Repair or replace the malfunctioning parts.

CONFIRM THE OPERATION

Confirm the operation again.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to

GI-46, "Intermittent Incident"

>> GO TO 1.

Revision: 2013 October

2014 JUKE

FILAMENT

DEF-47

< REMOVAL AND INSTALLATION >

DEF

REMOVAL AND INSTALLATION

FILAMENT

Inspection and Repair

INFOID:0000000009754291

INSPECTION

When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.

Attach probe circuit tester (in Volt range) to middle portion of
each filament.

If a filament is burned out, circuit tester registers 0 or battery
voltage.

To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.

REPAIR

REPAIR EQUIPMENT

• Conductive silver composition (Dupont No. 4817 or equivalent)

SEL122R

SEL263

SEL265

Revision: 2013 October

2014 JUKE

DEF-48

< REMOVAL AND INSTALLATION >

FILAMENT

• Ruler 30 cm (11.8 in) long
• Drawing pen
• Heat gun
• Alcohol
• Cloth

REPAIRING PROCEDURE

Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.

Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.

Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.

After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.

Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.

PIIA0215E

SEL012D

SEL013D

Revision: 2013 October

2014 JUKE