Nissan Juke (2014 year). Service Repair Manual

BCS-22

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

: For models without auto light system, this item is displayed, but cannot be used.

: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Service item

Setting item

Setting

CUSTOM A/LIGHT SET-

TING*

MODE 1*

Normal

MODE 2

More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)

MODE 3

More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)

MODE 4

Less sensitive setting than normal setting (Turns ON later than normal operation)

BATTERY SAVER SET

On*

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

ILL DELAY SET*

MODE 1*

45 sec.

Sets delay timer function timer operation time
(All doors closed)

MODE 2

Without the
function

MODE 3

30 sec.

MODE 4

60 sec.

MODE 5

90 sec.

MODE 6

120 sec.

MODE 7

150 sec.

MODE 8

180 sec.

HEAD LIGHT TIMER

MODE 1

10 sec.

Sets follow me home function activating time

MODE 2

30 sec.

AUTO LIGHT LOGIC SET*

MODE 1*

With twilight ON custom & with wiper INT, LO and HI

MODE 2

With twilight ON custom & with wiper LO and HI

MODE 3

With twilight ON custom & without

MODE 4

Without twilight ON custom & with wiper INT, LO and HI

MODE 5

Without twilight ON custom & with wiper LO and HI

MODE 6

Without twilight ON custom & without

Monitor item

[Unit]

Description

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

ENGINE STATE
[Stop/Stall/Crank/Run]

Indicates [Stop/Stall/Crank/Run] condition of engine states

VEH SPEED 1
[km/h]

Display the vehicle speed signal received from combination meter by numerical value
[Km/h]

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-23

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

*: For models without front fog lamp, this item is displayed, but cannot be monitored.

ACTIVE TEST

TURN SIGNAL R
[On/Off]

Each switch status that BCM judges from the combination switch reading function

TURN SIGNAL L
[On/Off]

TAIL LAMP SW
[On/Off]

HI BEAM SW
[On/Off]

HEAD LAMP SW1
[On/Off]

HEAD LAMP SW2
[On/Off]

PASSING SW
[On/Off]

AUTO LIGHT SW
[On/Off]

FR FOG SW*
[On/Off]

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

DOOR SW-BK
[On/Off]

Indicated [On/Off] condition of back door switch

OPTICAL SENSOR
[On/Off/NG]

NOTE:
This item is displayed, but cannot be monitored

OPTI SEN (DTCT)
[V]

The value of outside brightness voltage input from the optical sensor

OPTI SEN (FILT)
[V]

The value of outside brightness voltage filtered by BCM

Monitor item

[Unit]

Description

Test item

Operation

Description

TAIL LAMP

Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON

Off

Stops the tail lamp request signal transmission

HEAD LAMP

Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)

Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)

Off

Stops the high & low beam request signal transmission

Revision: 2013 October

2014 JUKE

BCS-24

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

: Except for NISMO models without front fog lamp, this item is displayed, but cannot be tested.

: For NISMO models with daytime running light system, this item is displayed, but cannot be tested.

: Except for NISMO models with daytime running light system.

: For NISMO models with daytime running light system.

WIPER

WIPER : CONSULT Function - WIPER

INFOID:0000000010286823

WORK SUPPORT

*:Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

FR FOG LAMP*

• Transmits the front fog lights request signal to IPDM E/R via CAN com-

munication to turn the front fog lamp ON*

• Transmits the daytime running light request signal to IPDM E/R via

CAN communication to turn the daytime running light ON*

Off

• Stops the front fog light request signal transmission*

• Stops the daytime running light request signal transmission*

DAYTIME RUNNING LIGHT*

Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R

Off

Stop the daytime running light request signal transmission

ILL DIM SIGNAL

NOTE:
This item is indicated, but can not tested

Off

Test item

Operation

Description

Service item

Setting item

Description

WIPER SPEED
SETTING

With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)

Off*

Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)

Monitor Item

[Unit]

Description

PUSH SW
[Off/On]

The switch status input from push-button ignition switch

VEH SPEED 1
[km/h]

Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication

FR WIPER HI
[Off/On]

Status of each switch judged by BCM using the combination switch reading function

FR WIPER LOW
[Off/On]

FR WASHER SW
[Off/On]

FR WIPER INT
[Off/On]

FR WIPER STOP
[Off/On]

Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.

INT VOLUME
[1

−

Status of each switch judged by BCM using the combination switch reading function

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-25

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

ACTIVE TEST

FLASHER

FLASHER : CONSULT Function (BCM - FLASHER)

INFOID:0000000010286813

WORK SUPPORT

*: Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

RR WIPER ON
[Off/On]

Status of each switch judged by BCM using the combination switch reading function

RR WIPER INT
[Off/On]

RR WASHER SW
[Off/On]

RR WIPER STOP
[Off/On]

Rear wiper motor (stop position) status input from the rear wiper motor

RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]

NOTE:
This item is displayed, but cannot be monitored.

Monitor Item

[Unit]

Description

Test item

Operation

Description

FR WIPER

Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.

Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.

INT

Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.

Off

Stops transmitting the front wiper request signal to stop the front wiper operation.

RR WIPER

Output the voltage to operate the rear wiper motor.

Off

Stops the voltage to stop the rear wiper motor.

Service item

Setting item

Setting

HAZARD ANSWER
BACK

Lock Only

With locking only

Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the Intelligent Key.

Unlk Only

With unlocking only

Lock&Unlk

With locking/unlocking

Off

Without the function

Monitor item

[Unit]

Description

REQ SW-DR
[On/Off]

Indicated [On/Off] condition of door request switch (driver side)

REQ SW-AS
[On/Off]

Indicated [On/Off] condition of door request switch (passenger side)

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

Revision: 2013 October

2014 JUKE

BCS-26

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

AIR CONDITIONER

AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Automatic A/
C)

INFOID:0000000010286779

DATA MONITOR

Display Item List
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

INTELLIGENT KEY

INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)

INFOID:0000000010286782

WORK SUPPORT

TURN SIGNAL R
[On/Off]

Each switch status that BCM detects from the combination switch reading function

TURN SIGNAL L
[On/Off]

HAZARD SW
[On/Off]

The switch status input from the hazard switch

RKE-LOCK
[On/Off]

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK
[On/Off]

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-PANIC
[On/Off]

Indicates [On/Off] condition of PANIC button of Intelligent Key

Monitor item

[Unit]

Description

Test item

Operation

Description

FLASHER

Outputs the voltage to turn the right side turn signal lamps ON

Outputs the voltage to turn the left side turn signal lamps ON

Off

Stops the voltage to turn the turn signal lamps OFF

Monitor Item [Unit]

Contents

FAN ON SIG

[On/Off]

Displays the blower fan status as jugged from the A/C auto amp.

AIR COND SW

[On/Off]

Displays [COMP (On)/COMP (Off)] status as judged from the A/C auto amp.

Monitor item

Description

INSIDE ANT DIAGNOSIS

This function allows inside key antenna self-diagnosis

LOCK/UNLOCK BY I-KEY

Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation

ENGINE START BY I-KEY

Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

TRUNK/GLASS HATCH OPEN

NOTE:
This item is displayed, but cannot be monitored

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-27

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

SELF-DIAG RESULT

Refer to

BCS-59, "DTC Index"

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

HORN WITH KEYLESS LOCK

Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
operate (OFF) with this mode
• On: Operate
• Off: Non-operation

PANIC ALARM SET

Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following with this mode
• MODE 1: 0.5 sec
• MODE 2: Non-operation
• MODE 3: 1.5 sec

TRUNK OPEN DELAY

NOTE:
This item is displayed, but cannot be monitored

LO- BATT OF KEY FOB WARN

Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

ANTI KEY LOCK IN FUNCTI

Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation

HAZARD ANSWER BACK

Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation

ANS BACK I-KEY LOCK

Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation

ANS BACK I-KEY UNLOCK

Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation

SHORT CRANKING OUTPUT

Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec

CONFIRM KEY FOB ID

It can be checked whether Intelligent Key ID code is registered or not in this mode

AUTO LOCK SET

Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes

Monitor item

Description

Monitor Item

Condition

REQ SW -DR

Indicates [On/Off] condition of door request switch (driver side)

REQ SW -AS

Indicates [On/Off] condition of door request switch (passenger side)

REQ SW -BD/TR

Indicates [On/Off] condition of back door request switch

Revision: 2013 October

2014 JUKE

BCS-28

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

: It is displayed but does not operate on CVT models.

: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.

ACTIVE TEST

PUSH SW

Indicates [On/Off] condition of push-button ignition switch

CLUTCH SW*

Indicates [On/Off] condition of clutch interlock switch

BRAKE SW 1

Indicates [On/Off]*

condition of stop lamp switch power supply

BRAKE SW 2

Indicates [On/Off] condition of stop lamp switch

DETE/CANCL SW

Indicates [On/Off] condition of P position

SFT PN/N SW

Indicates [On/Off] condition of P or N position

UNLK SEN -DR

Indicates [On/Off] condition of driver door UNLOCK status

PUSH SW -IPDM

Indicates [On/Off] condition of push-button ignition switch

IGN RLY1 -F/B

Indicates [On/Off] condition of ignition relay 1

DETE SW -IPDM

Indicates [On/Off] condition of P position

SFT PN -IPDM

Indicates [On/Off] condition of P or N position

SFT P -MET

Indicates [On/Off] condition of P position

SFT N -MET

Indicates [On/Off] condition of N position

ENGINE STATE

Indicates [Stop/Stall/Crank/Run] condition of engine states

S/L LOCK-IPDM

NOTE:
This item is displayed, but cannot be monitored

S/L UNLK-IPDM

NOTE:
This item is displayed, but cannot be monitored

S/L RELAY-REQ

NOTE:
This item is displayed, but cannot be monitored

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h]

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]

DOOR STAT-DR

Indicates [LOCK/READY/UNLK] condition of driver side door status

DOOR STAT-AS

Indicates [LOCK/READY/UNLK] condition of passenger side door status

ID OK FLAG

Indicates [Set/Reset] condition of key ID

PRMT ENG STRT

Indicates [Set/Reset] condition of engine start possibility

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-LOCK

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

RKE-PANIC

Indicates [On/Off] condition of PANIC button of Intelligent Key

RKE-MODE CHG

Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored

Monitor Item

Condition

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-29

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

COMB SW

COMB SW : CONSULT Function (BCM - COMB SW)

INFOID:0000000009751602

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Test item

Description

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation

INSIDE BUZZER

This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation

INDICATOR

This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation

INT LAMP

This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation

LCD

This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT screen is touched
• NO KY: Key warning lamp indicator when CONSULT screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT screen is touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT screen is touched

FLASHER

This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched

HORN

This test is able to check horn operation
The horn is activated after “ON” on CONSULT screen is touched

P RANGE

This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched

PUSH SWITCH INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.

TRUNK/BACK DOOR

This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT screen is touched.

Monitor item [UNIT]

Description

FR WIPER HI
[Off/On]

Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.

FR WIPER LOW
[Off/On]

Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.

Revision: 2013 October

2014 JUKE

BCS-30

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

BCM

BCM : CONSULT Function (BCM - BCM)

INFOID:0000000009751603

WORK SUPPORT

IMMU

IMMU : CONSULT Function (BCM - IMMU)

INFOID:0000000010286806

WORK SUPPORT

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

FR WASHER SW
[Off/On]

Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.

FR WIPER INT
[Off/On]

Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.

INT VOLUME
[1 - 7]

Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.

TURN SIGNAL R
[Off/On]

Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.

TURN SIGNAL L
[Off/On]

Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.

TAIL LAMP SW
[Off/On]

Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.

HI BEAM SW
[Off/On]

Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.

HEAD LAMP SW 1
[Off/On]

Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
switch reading function.

HEAD LAMP SW 2
[Off/On]

Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
switch reading function.

PASSING SW
[Off/On]

Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.

AUTO LIGHT SW
[Off/On]

Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.

FR FOG SW
[Off/On]

Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.

Monitor item [UNIT]

Description

Item

Description

RESET SETTING VALUE

Return a value set with Work Support of each system to a default value in factory shipment.

Service item

Description

CONFIRM DONGLE ID

It is possible to check that dongle unit is applied to the vehicle.

Monitor item

Content

CONFRM ID ALL

Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.

CONFIRM ID4

CONFIRM ID3

CONFIRM ID2

CONFIRM ID1

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-31

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

ACTIVE TEST

BATTERY SAVER

BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)

INFOID:0000000010286820

WORK SUPPORT

*:Factory setting

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

NOT REGISTERED

Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.

TP 4

Indicates the number of IDs that are registered.

TP 3

TP 2

TP 1

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

Monitor item

Content

Test item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

Service item

Setting item

Setting

ROOM LAMP TIMER SET

MODE 1

30 min.

Sets the interior room lamp battery saver timer operating
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed
once.

MODE 2

60 min.

MODE 3

15 min.

BATTERY SAVER SET

With the exterior lamp battery saver function

Off

Without the exterior lamp battery saver function

Monitor item

[Unit]

Description

REQ SW-DR
[On/Off]

Indicated [On/Off] condition of door request switch (driver side)

REQ SW-AS
[On/Off]

Indicated [On/Off] condition of door request switch (passenger side)

REQ SW-RR
[On/Off]

NOTE:
This item is displayed, but cannot be monitored

REQ SW-RL
[On/Off]

NOTE:
This item is displayed, but cannot be monitored

PUSH SW
[On/Off]

Indicates [On/Off] condition of push-button ignition switch

UNLK SEN -DR
[On/Off]

Indicates [On/Off] condition of driver door UNLOCK status

DOOR SW-DR
[On/Off]

Indicated [On/Off] condition of front door switch (driver side)

DOOR SW-AS
[On/Off]

Indicated [On/Off] condition of front door switch (passenger side)

Revision: 2013 October

2014 JUKE

BCS-32

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

TRUNK

TRUNK : CONSULT Function (BCM - TRUNK)

INFOID:0000000010286783

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

THEFT ALM

THEFT ALM : CONSULT Function (BCM - THEFT)

INFOID:0000000010286787

WORK SUPPORT

DOOR SW-RR
[On/Off]

Indicated [On/Off] condition of rear door switch RH

DOOR SW- RL
[On/Off]

Indicated [On/Off] condition of rear door switch LH

DOOR SW- BK
[On/Off]

Indicated [On/Off] condition of back door switch

CDL LOCK SW
[On/Off]

Indicated [On/Off] condition of lock signal from door lock unlock switch

CDL UNLOCK SW
[On/Off]

Indicated [On/Off] condition of unlock signal from door lock unlock switch

TRNK/HAT MNTR
[On/Off]

NOTE:
This item is displayed, but cannot be monitored

KEY CYL LK-SW
[On/Off]

Indicated [On/Off] condition of lock signal from door key cylinder

KEY CYL UN-SW
[On/Off]

Indicated [On/Off] condition of unlock signal from door key cylinder

RKE-LOCK
[On/Off]

Indicates [On/Off] condition of LOCK signal from Intelligent Key

RKE-UNLOCK
[On/Off]

Indicates [On/Off] condition of UNLOCK signal from Intelligent Key

Monitor item

[Unit]

Description

Test item

Operation

Description

BATTERY SAVER

Off

Cuts the interior room lamp power supply.

Outputs the interior room lamp power supply.

Monitor Item

Contents

PUSH SW

Indicates [On/Off] condition of push switch

UNLK SEN -DR

Indicates [On/Off] condition of unlock sensor

VEH SPEED 1

Indicates [Km/h] condition of vehicle speed signal from combination meter

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-33

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

RETAIND PWR

Service Item

Description

SECURITY ALARM SET

This mode is able to confirm and change security alarm ON-OFF setting.

THEFT ALM TRG

The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.

Monitored Item

Description

REQ SW -DR

Indicates [ON/OFF] condition of door request switch (driver side).

REQ SW -AS

Indicates [ON/OFF] condition of door request switch (passenger side).

REQ SW -RR

NOTE:
This is displayed even when it is not equipped.

REQ SW -RL

NOTE:
This is displayed even when it is not equipped.

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

DOOR SW-DR

Indicates [ON/OFF] condition of front door switch (driver side).

DOOR SW-AS

Indicates [ON/OFF] condition of front door switch (passenger side).

DOOR SW-RR

Indicates [ON/OFF] condition of rear door switch RH.

DOOR SW-RL

Indicates [ON/OFF] condition of rear door switch LH.

DOOR SW-BK

Indicates [ON/OFF] condition of back door switch.

CDL LOCK SW

Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.

CDL UNLOCK SW

Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.

KEY CYL LK-SW

Indicates [ON/OFF] condition of lock signal from door key cylinder.

KEY CYL UN-SW

Indicates [ON/OFF] condition of unlock signal from door key cylinder.

TR/BD OPEN SW

Indicates [ON/OFF] condition of back door opener switch.

TRNK/HAT MNTR

NOTE:
This is displayed even when it is not equipped.

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This is displayed even when it is not equipped.

Test Item

Description

THEFT IND

This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.

VEHICLE SECURITY HORN

This test is able to check horns operation.
Horns are activated for 0.5 seconds after “ON” on CONSULT screen is touched.

HEADLAMP(HI)

This test is able to check headlamp operation.
Headlamps are activated for 0.5 seconds after “ON” on CONSULT screen is touched.

FLASHER

This test is able to check hazard warning lamp operation.
Hazard warning lamps are activated after “ON” on CONSULT screen is touched.

Revision: 2013 October

2014 JUKE

BCS-34

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

DIAGNOSIS SYSTEM (BCM)

RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)

INFOID:0000000010286810

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

SIGNAL BUFFER

SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)

INFOID:0000000009751609

DATA MONITOR

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

ACTIVE TEST

AIR PRESSURE MONITOR

AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)

INFOID:0000000010286829

APPLICATION ITEM

CONSULT performs the following functions via CAN communication with BCM.

SELF DIAGNOSTIC RESULT

Refer to

BCS-59, "DTC Index"

DATA MONITOR MODE

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

Monitor Item

Description

DOOR SW-DR

Indicates [ON/OFF] condition of driver side door switch.

DOOR SW-AS

Indicates [ON/OFF] condition of passenger side door switch.

Monitor item [UNIT]

Description

PUSH SW
[Off/On]

Displays the status of the push-button ignition switch (push switch) judged by BCM.

Test item

Opera-

tion

Description

OIL PRESSURE SW

Off

NOTE:
This item is indicated, but not tested.

Diagnosis mode

Function Description

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Work Support

Components can be quickly and accurately adjusted.

Revision: 2013 October

2014 JUKE

BCS

DIAGNOSIS SYSTEM (BCM)

BCS-35

< SYSTEM DESCRIPTION >

[WITH INTELLIGENT KEY SYSTEM]

ACTIVE TEST MODE

NOTE:
After completing the work below, perform an active test.
1.

Check ID registration state and perform self-diagnosis.

Erase the self-diagnosis result history.

WORK SUPPORT

Monitor item (Unit)

Remarks

AIR PRESS FL
(kPa, kg/cm2 or Psi)

Tire pressure

AIR PRESS FR
(kPa, kg/cm2 or Psi)

AIR PRESS RR
(kPa, kg/cm2 or Psi)

AIR PRESS RL
(kPa, kg/cm2 or Psi)

ID REGST FL1
(Yet, Done)

Registration ID

ID REGST FR1
(Yet, Done)

ID REGST RR1
(Yet, Done)

ID REGST RL1
(Yet, Done)

WARNING LAMP
(On/Off)

Low tire pressure warning lamp

BUZZER
(On/Off)

NOTE:
This item is displayed, but cannot be use this item.

Item

Description

WARNING LAMP

Low tire pressure warning lamp can be turned ON arbitrarily.

ID REGIST WARNING

NOTE:
Displayed but not used in TPMS.

RUN FLAT TIRE W/L

NOTE:
Displayed but not used in TPMS.

RUN FLAT/T WARN BUZZER

NOTE:
Displayed but not used in TPMS.

FLASHER

Turn signal lamps can be turned ON arbitrarily.

HORN

This test is able to check to check that the horn sounds.

Item

Description

ID READ

Registered tire pressure sensor ID can be displayed.

ID REGIST

Tire pressure sensor ID can be registered.

Revision: 2013 October

2014 JUKE

BCS-36

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

BCM

ECU DIAGNOSIS INFORMATION

BCM

Reference Value

INFOID:0000000009751611

VALUES ON THE DIAGNOSIS TOOL

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.

CONSULT MONITOR ITEM

Monitor Item

Condition

Value/Status

FR WIPER HI

Other than front wiper switch HI

Off

Front wiper switch HI

FR WIPER LOW

Other than front wiper switch LO

Off

Front wiper switch LO

FR WASHER SW

Front washer switch OFF

Off

Front washer switch ON

FR WIPER INT

Other than front wiper switch INT

Off

Front wiper switch INT

FR WIPER STOP

Front wiper is not in STOP position

Off

Front wiper is in STOP position

INT VOLUME

Wiper intermittent dial is in a dial position 1 - 7

Wiper intermittent dial

position

RR WIPER ON

Other than rear wiper switch ON

Off

Rear wiper switch ON

RR WIPER INT

Other than rear wiper switch INT

Off

Rear wiper switch INT

RR WASHER SW

Rear washer switch OFF

Off

Rear washer switch ON

RR WIPER STOP

Rear wiper is in STOP position

Off

Rear wiper is not in STOP position

TURN SIGNAL R

Other than turn signal switch RH

Off

Turn signal switch RH

TURN SIGNAL L

Other than turn signal switch LH

Off

Turn signal switch LH

TAIL LAMP SW

Other than lighting switch 1ST and 2ND

Off

Lighting switch 1ST or 2ND

HI BEAM SW

Other than lighting switch HI

Off

Lighting switch HI

HEAD LAMP SW 1

Other than lighting switch 2ND

Off

Lighting switch 2ND

HEAD LAMP SW 2

Other than lighting switch 2ND

Off

Lighting switch 2ND

PASSING SW

Other than lighting switch PASS

Off

Lighting switch PASS

AUTO LIGHT SW

Other than lighting switch AUTO

Off

Lighting switch AUTO

Revision: 2013 October

2014 JUKE

BCS

BCM

BCS-37

< ECU DIAGNOSIS INFORMATION >

[WITH INTELLIGENT KEY SYSTEM]

FR FOG SW

Front fog lamp switch OFF

Off

Front fog lamp switch ON

DOOR SW-DR

Driver door closed

Off

Driver door opened

DOOR SW-AS

Passenger door closed

Off

Passenger door opened

DOOR SW-RR

Rear RH door closed

Off

Rear RH door opened

DOOR SW-RL

Rear LH door closed

Off

Rear LH door opened

DOOR SW-BK

Back door closed

Off

Back door opened

CDL LOCK SW

Other than power door lock switch LOCK

Off

Power door lock switch LOCK

CDL UNLOCK SW

Other than power door lock switch UNLOCK

Off

Power door lock switch UNLOCK

KEY CYL LK-SW

Other than driver door key cylinder LOCK position

Off

Driver door key cylinder LOCK position

KEY CYL UN-SW

Other than driver door key cylinder UNLOCK position

Off

Driver door key cylinder UNLOCK position

HAZARD SW

Hazard switch is OFF

Off

Hazard switch is ON

REAR DEF SW

Rear window defogger switch OFF

Off

Rear window defogger switch ON

TR/BD OPEN SW

Back door opener switch OFF

Off

While the back door opener switch is turned ON

TRNK/HAT MNTR

NOTE:
The item is indicated, but not monitored.

Off

FAN ON SIG

Blower fan OFF

Off

Blower fan ON

AIR COND SW

Air conditioner OFF (A/C switch indicator OFF)

Off

Air conditioner ON (A/C switch indicator ON)

RKE-LOCK

LOCK button of the key is not pressed

Off

LOCK button of the key is pressed

RKE-UNLOCK

UNLOCK button of the key is not pressed

Off

UNLOCK button of the key is pressed

RKE-TR/BD

NOTE:
The item is indicated, but not monitored.

Off

RKE-PANIC

PANIC button of the key is not pressed

Off

PANIC button of the key is pressed

RKE-MODE CHG

LOCK/UNLOCK button of the key is not pressed and held simultaneously

Off

LOCK/UNLOCK button of the key is pressed and held simultaneously

OPTI SEN (DTCT)

Bright outside of the vehicle

Close to 5 V

Dark outside of the vehicle

Close to 0 V

Monitor Item

Condition

Value/Status

Revision: 2013 October

2014 JUKE

Nissan Juke (2014 year). Service Repair Manual - part 14