Nissan Juke (2016 year). Service Repair Manual - part 618

TM-136

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

FINAL DRIVE

FINAL DRIVE

Exploded View

INFOID:0000000012200829

FINAL DRIVE

FINAL DRIVE

Disassembly and Assembly

INFOID:0000000012200830

DISASSEMBLY

1. Remove final gear bolts and then separate the final gear from differential case.
2. Remove differential side bearing (clutch housing side) using

Tool and pullers (B).

CAUTION:

Hook a puller on the cage of differential side bearing.

1.

Differential side bearing outer 
race (clutch housing side)

2.

Differential side bearing (clutch 
housing side)

3.

Differential case assembly

4.

Final gear

5.

Differential side bearing (tran-
saxle case side)

6.

Differential side bearing outer 
race (transaxle case side)

7.

Differential side bearing adjust-
ing shim

 : Replace the parts as a set.

 : N·m (kg-m, ft-lb)

JSDIA5268GB

Tool number

A: ST33061000 (J-8107-2)

PCIB1876E

Revision: November 2015

2016 JUKE

FINAL DRIVE

TM-137

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3. Remove differential side bearing (transaxle case side) using

Tool and puller.

CAUTION:

Hook a puller on the inner race of differential side bearing.

INSPECTION AFTER DISASSEMBLY

Bearing

• Check for bearings damage and rough rotation. If necessary,

replace with a new one.

CAUTION:

When replacing tapered roller bearing, replace outer and inner

races as a set.

ASSEMBLY

1. Press in differential side bearing (transaxle case side) to differ-

ential case using Tools.

CAUTION:

Replace differential side bearing and differential side bear-

ing outer race as a set.

2. Press in differential side bearing (clutch housing side) to differ-

ential case using Tools.

CAUTION:

• Do not reuse differential side bearing and differential side

bearing outer race.

• Replace differential side bearing and differential side

bearing outer race as a set.

Tool number

A: ST33061000 (J-8107-2)

PCIB0951E

SPD715

Tool number

: KV38102510 ( — )
: ST30720000 (J-25405)

PCIB0952E

Tool number

A: ST30720000 (J-25405)
B: KV38102510 ( — )

JSDIA5267GB

Revision: November 2015

2016 JUKE

TM-138

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

FINAL DRIVE

3. Install final gear into differential case and tighten final gear bolts

to the specified torque. Refer to 

TM-136, "Exploded View"

.

SCIA0912E

Revision: November 2015

2016 JUKE

SHIFT CONTROL

TM-139

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SHIFT CONTROL

Exploded View

INFOID:0000000012200831

SHIFT CONTROL

Disassembly and Assembly

INFOID:0000000012200832

DISASSEMBLY

1.

Clutch housing

2.

Retaining pin

3.

Reverse shift fork

4.

Reverse fork rod

5.

Return spring

6.

Striking rod assembly

7.

Striking rod shim

8.

Striking rod adjusting shim

9.

Shifter lever A

10. Shifter lever B

11. Guide bolt

12. Selector lever

13. Transaxle case

14. 3rd-4th shift fork

15. 3rd-4th fork rod

16. 1st-2nd shift fork

17. 1st-2nd fork rod

18. 5th-6th shift fork

19. 5th-6th fork rod

 : Replace the parts as a set.

 : Always replace after every disassembly.

JSDIA5279GB

Revision: November 2015

2016 JUKE

TM-140

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

SHIFT CONTROL

1. Remove return spring to striking rod assembly.

INSPECTION AFTER DISASSEMBLY

Striking Rod Assembly and Return Spring

• Check contact surfaces and sliding area for wear, damage, bend-

ing, etc. If necessary, replace parts.

Fork Rod and Shift Fork

PCIB1867E

PCIB1868E

Revision: November 2015

2016 JUKE

SHIFT CONTROL

TM-141

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

• Check contact surfaces and sliding area for wear, damage, bend-

ing, etc. If necessary, replace parts.

• Check if the width of shift fork hook (sliding area with coupling

sleeve) is within allowable specification below.

ASSEMBLY

1. Temporarily install return spring to striking rod assembly.

CAUTION:

Be careful with the orientation of return spring.

PCIB1869E

Item

One-side wear specification

Sliding width of new part

1st-2nd

0.2 mm (0.008 in)

7.80 - 7.93 mm

(0.3071 - 0.3122 in)

3rd-4th

0.2 mm (0.008 in)

7.80 - 7.93 mm

(0.3071 - 0.3122 in)

5th-6th

0.2 mm (0.008 in)

6.10 - 6.23 mm

(0.2402 - 0.2453 in)

Reverse

0.2 mm (0.008 in)

12.80 - 12.93 mm

(0.5039 - 0.5091 in)

SMT801D

PCIB1830E

Revision: November 2015

2016 JUKE

TM-142

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F52H]

SHIFT CONTROL

2. Attach one end of the return spring to striking interlock of striking

rod assembly while holding return spring.

CAUTION:

• When installing, check that return spring is securely

seated in the groove of striking interlock of striking rod

assembly.

PCIB1831E

PCIB1833E

Revision: November 2015

2016 JUKE

SERVICE DATA AND SPECIFICATIONS (SDS)

TM-143

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[6MT: RS6F52H]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

General Specification

INFOID:0000000012200833

TRANSAXLE

Engine type

MR16DDT

Transaxle model

RS6F52H

Model code number

3YW0D

Number of speed

6

Synchromesh type

Warner

Shift pattern

Gear ratio

1st

3.727

2nd

2.043

3rd

1.392

4th

1.055

5th

0.865

6th

0.732

Reverse

3.641

Number of teeth

Input gear

1st

11

2nd

23

3rd

28

4th

36

5th

52

6th

56

Reverse

11

Main gear

1st

41

2nd

47

3rd

39

4th

38

5th

45

6th

41

Reverse

38

Reverse idler gear

Front

37

Rear

39

Oil level

mm (in)

38.5 - 45.5 (1.516 - 1.791)

Oil capacity (Reference)

 (US pt, Imp pt)

1.9 (4, 3-3/8)

Remarks

Reverse synchronizer

Installed

Double-cone synchronizer

3rd

Triple-cone synchronizer

1st and 2nd

PCIB1769E

Revision: November 2015

2016 JUKE