Nissan Juke (2016 year). Service Repair Manual - part 544

 

  Index      Manuals     Nissan Juke (2016 year) - Service and Repair Manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     542      543      544      545     ..

 

 

Nissan Juke (2016 year). Service Repair Manual - part 544

 

 

RF-20

< DTC/CIRCUIT DIAGNOSIS >

SUNROOF MOTOR ASSEMBLY

SUNROOF MOTOR ASSEMBLY

Component Function Check

INFOID:0000000012196966

1.

CHECK SUNROOF MOTOR FUNCTION

Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Check sunroof switch. Refer to 

RF-21, "Diagnosis Procedure"

.

2.

CHECK SUNROOF MOTOR ASSEMBLY INPUT SIGNAL

1. Start engine.

2. Drive the vehicle at more than 40 km/h (25 MPH).

CAUTION:

Always drive vehicle at a safe speed.

NOTE:

This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.

If a road test is expected to be easier, it is unnecessary to lift the vehicle.

3. Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

RF-20, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196967

SUNROOF MOTOR ASSEMBLY

1.

CHECK SUNROOF MOTOR ASSEMBLY INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect combination meter harness connector and sunroof motor assembly harness connector.

3. Check continuity between combination meter harness connector and sunroof motor assembly harness

connector.

4. Check continuity between sunroof motor assembly harness connector and ground.

Is the inspection result normal?

YES

>> Check combination meter. Refer to 

MWI-53, "COMBINATION METER : Diagnosis Procedure"

.

NO

>> Repair or replace harness or connector.

Combination meter

Sunroof motor assembly

Continuity

Connector

Terminal

 Connector

Terminal

M34

4

R11

8

Exists

Sunroof motor assembly

Ground

Continuity 

 Connector

Terminal

R11

8

Not existed

Revision: November 2015

2016 JUKE

SUNROOF SWITCH

RF-21

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

SUNROOF SWITCH

Component Function Check

INFOID:0000000012196968

1.

CHECK SUNROOF MOTOR FUNCTION

Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

RF-21, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196969

1.

PERFORM INITIALIZATION PROCEDURE

1. Initialization procedure is executed and operation is confirmed. Refer to 

RF-17, "ADDITIONAL SERVICE

WHEN REPLACING CONTROL UNIT : Special Repair Requirement"

.

2. Check tilt up/down & slide open/close operations with sunroof switch.
Is the inspection result normal?

YES

>> INSPECTION END

NO

>> GO TO 2.

2.

CHECK SUNROOF SWITCH GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect sunroof switch harness connector.

3. Check continuity between sunroof switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK SUNROOF SWITCH INPUT SIGNAL 

1. Turn ignition switch ON.

2. Check voltage between sunroof switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

CHECK SUNROOF SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect sunroof motor assembly harness connector.

3. Check continuity between sunroof motor assembly harness connector and sunroof switch harness con-

nector.

Sunroof switch

Ground

Continuity 

 Connector

Terminal

R5

2

Existed

(+)

(

−

)

Voltage (V)

(Approx.)

sunroof switch

Connector

Terminal

R5

1

Ground

Battery Voltage

3

Revision: November 2015

2016 JUKE

RF-22

< DTC/CIRCUIT DIAGNOSIS >

SUNROOF SWITCH

4. Check continuity between sunroof motor assembly harness connector and ground. 

Is the inspection result normal?

YES

>> Replace sunroof motor assembly. Refer to 

RF-37, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

5.

CHECK SUNROOF SWITCH

Check sunroof switch.

Refer to 

RF-22, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace sunroof switch (built in map lamp assembly). Refer to 

RF-45, "Removal and Installation"

.

Component Inspection

INFOID:0000000012196970

SUNROOF SWITCH

1.

CHECK SUNROOF SWITCH

1. Turn ignition switch OFF.

2. Disconnect sunroof switch harness connector.

3. Check continuity sunroof switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sunroof switch. Refer to 

RF-45, "Removal and Installation"

.

Sunroof motor assembly

Sunroof switch

Continuity

Connector

Terminal

 Connector

Terminal

R11

5

R5

1

Existed

10

3

Sunroof motor assembly

Ground

Continuity

 Connector

Terminal

R11

5

Not existed

10

Terminals

Condition

Continuity

1

2

Sunroof switch is operated 

TILT DOWN or SLIDE OPEN

Existed

Other than above

Not existed

3

Sunroof switch is operated

TILT UP or SLIDE CLOSE

Existed

Other than above

Not existed

Revision: November 2015

2016 JUKE

SUNROOF DOES NOT OPERATE PROPERLY

RF-23

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

SYMPTOM DIAGNOSIS

SUNROOF DOES NOT OPERATE PROPERLY

Description

INFOID:0000000012196971

Sunroof does not operate normally.

• Glass lid does not slide or tilt.

• Judder occurs during sliding operation of glass lid.

• Sliding or tilting operation of glass lid is slow.

Diagnosis Procedure

INFOID:0000000012196972

1.

CHECK GLASS LID

Check the following items.

• Cracks, damage, or deformation of weather-strip.

• Sticking of weather-strip.

• Loose or missing glass lid mounting blot.

• Misalignment of glass lid.

Refer to 

RF-34, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK SUNROOF FRAME ASSEMBLY

Check the following items.

• Damage, deformation or trapped foreign material of slide rail.

• Insufficient application of grease to sliding section of slide rail.

Refer to 

RF-40, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK SUNSHADE

Check sunshade for damage, deformation, of interference with other parts.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground circuit. 

Refer to 

BCS-87, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT

Check sunroof motor assembly power supply and ground circuit.

Refer to 

RF-20, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK SUNROOF SWITCH

Check sunroof switch.

Refer to 

RF-21, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 7.

Revision: November 2015

2016 JUKE

RF-24

< SYMPTOM DIAGNOSIS >

SUNROOF DOES NOT OPERATE PROPERLY

NO

>> Repair or replace the malfunctioning parts.

7.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> GO TO 1.

Revision: November 2015

2016 JUKE

AUTO OPERATION DOES NOT OPERATE

RF-25

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

AUTO OPERATION DOES NOT OPERATE

Description

INFOID:0000000012196973

Auto operation does not operate

• Auto operation of glass lid does not operate.

• Glass lid stops halfway.

• Anti-pinch function operates.

Diagnosis Procedure

INFOID:0000000012196974

1.

CHECK GLASS LID

Check the following items.

• Cracks, damage, or deformation of weather-strip.

• Sticking of weather-strip.

• Loose or missing glass lid mounting blot.

• Misalignment of glass lid.

Refer to 

RF-34, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK WIND DEFLECTOR

Check wind deflector for deformation and interference.

Refer to 

RF-44, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CHECK SUNROOF FRAME ASSEMBLY

Check the following items.

• Damage, deformation or trapped foreign material of slide rail.

• Insufficient application of grease to sliding section of slide rail.

Refer to 

RF-40, "Removal and Installation"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 

Refer to 

RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace sunroof motor assembly. Refer to 

RF-37, "Removal and Installation"

.

Revision: November 2015

2016 JUKE

RF-26

< SYMPTOM DIAGNOSIS >

SUNROOF DOES NOT OPERATE ANTI-PINCH FUNCTION

SUNROOF DOES NOT OPERATE ANTI-PINCH FUNCTION

Diagnosis Procedure

INFOID:0000000012196975

1.

PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 

Refer to 

RF-17, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description"

.

Is the inspection result normal?

YES

>> Inspection end.

NO

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

. 

Revision: November 2015

2016 JUKE

RETAINED POWER OPERATION DOES NOT OPERATE PROPERLY

RF-27

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

RETAINED POWER OPERATION DOES NOT OPERATE PROPERLY

Diagnosis Procedure

INFOID:0000000012196976

1.

CHECK DOOR SWITCH

Check door switch. 

Refer to 

DLK-77, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK SUNROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND

Check sunroof motor assembly power supply and ground circuit.

Refer to 

RF-20, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

REPLACE BCM

• Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

• Confirm the operation after replacement.
Is the result normal?

YES

>> INSPECTION END

NO

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

Revision: November 2015

2016 JUKE

 

 

 

 

 

 

 

Content      ..     542      543      544      545     ..