Nissan Juke (2016 year). Service Repair Manual - part 506

PARKING BRAKE CONTROL

PB-7

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

Removal and Installation

INFOID:0000000012200167

REMOVAL

1. Remove rear tires with power tool.
2. Remove the center console assembly. Refer to 

IP-24, "Removal and Installation"

.

3. Disconnect the parking brake switch harness connector.
4. Remove adjusting nut (1) and loosen front cable.
5. Remove the parking brake lever assembly.

1.

Parking brake lever assembly

2.

Adjusting nut

3.

Parking brake switch

4.

Front cable

5.

Rear cable (LH)

6.

Rear cable (RH)

: Apply multi-purpose grease.

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

: Always replace after every disassembly.

JSFIA0466GB

JPFIB0131ZZ

Revision: November 2015

2016 JUKE

PB-8

< REMOVAL AND INSTALLATION >

PARKING BRAKE CONTROL

6. Remove rear cable with the following procedure.
a. Pull equalizer (A) of the front cable (1) in a rearward direction. 
b. Push the equalizer upward to remove the rear cable (2).
7. Remove center muffler and heat plate. Refer to 

EX-10,

"Removal and Installation"

.

8. Remove brake shoe, and remove rear cable from toggle lever.

Refer to 

PB-9, "Exploded View"

.

9. Remove rear cable mounting bolts, pull out rear cable from vehi-

cle.

10. Press the pawl (1) to remove the rear cable from the vehicle.

INSTALLATION

Note the following, install in the reverse order of the removal.

• Never reuse adjusting nut.

• Perform adjustment after installation. Refer to 

PB-4, "Inspection and Adjustment"

.

Adjustment

INFOID:0000000012200168

ADJUSTMENT AFTER INSTALLATION

Adjust the parking brake lever stroke. Refer to 

PB-4, "Inspection and Adjustment"

.

JPFIB0129ZZ

JPFIB0130ZZ

Revision: November 2015

2016 JUKE

PARKING BRAKE SHOE

PB-9

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

PARKING BRAKE SHOE

Exploded View

INFOID:0000000012200169

Removal and Installation

INFOID:0000000012200170

REMOVAL

WARNING:

Since dust covering the parking brake has an affect on human body, the dust must be removed with a

dust collector. Never splatter the dust with an air blow gun.

1. Remove rear tires with power tool.
2. Remove disc rotor.

• 2WD: Refer to 

RAX-7, "Removal and Installation"

.

• AWD: Refer to 

RAX-16, "Removal and Installation"

.

CAUTION:

Parking brake completely in the released position.

1.

Anti-rattle pin

2.

Back plate

3.

Toggle lever

4.

Parking brake shoe

5.

Brake strut

6.

Return spring

7.

Spring

8.

Adjuster

: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.

JPFIB0086ZZ

Revision: November 2015

2016 JUKE

PB-10

< REMOVAL AND INSTALLATION >

PARKING BRAKE SHOE

3. Remove return spring (1) of the upper side.

4. Remove return spring (1) of the lower side.

5. Remove spring (1).

CAUTION:

Never drop the removed parts.

6. Remove parking brake shoes, adjuster, brake strut and toggle

lever.

CAUTION:

• The parking brake shoes for the front wheels are made of

different materials from those for the rear wheels. Never

misidentify them when removing.

• Never drop the removed parts.

7. Press the rear cable spring (1) against spring tension to remove

rear cable (3) from the clamp (A) of toggle lever (2).

CAUTION:

Never bend rear cable.

8. For the removal of back plate.

• 2WD: Refer to 

RAX-7, "Removal and Installation"

.

• AWD: Refer to 

RAX-16, "Removal and Installation"

.

INSTALLATION

Note the following, install in the reverse order of removal.

• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe.

CAUTION:

The parking brake shoes for the front wheels are made of different materials from those for the rear

wheels. Never misidentify them when removing and replacing.

JSFIA0485ZZ

JSFIA0486ZZ

JSFIA0487ZZ

JSFIA0488ZZ

Revision: November 2015

2016 JUKE

PARKING BRAKE SHOE

PB-11

< REMOVAL AND INSTALLATION >

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

• Assemble adjusters so that threaded part is expanded when rotat-

ing it in the direction shown by arrow.

• Shorten adjuster by rotating it.

• When disassembling apply PBC (Poly Butyl Cuprysil) grease or sil-

icone-based grease to threads.

• Check that the component parts of the parking brake shoe are

properly installed.

• Check brake shoe sliding surface and drum inner surface for

grease. Wipe it off if it adhere on the surfaces.

Inspection and Adjustment

INFOID:0000000012200171

INSPECTION AFTER REMOVAL

Lining Thickness Inspection

• Check thickness (A) of lining.

Drum Inner Diameter Inspection

• Check inner diameter (B) of drum. 

Other Inspections

Check the following items, and replace the parts if necessary.

• Lining for excessive wear, damage, and peeling.

• Brake shoe sliding surface for excessive wear and damage.

• Anti-rattle pin for excessive wear, damage and rust.

• Return spring and spring for settling, excessive wear, damage, and rust.

A : For right side brake
B : For left side brake

: Vehicle front

: Adjuster expands

JPFIB0087ZZ

JSFIA0489ZZ

A

: Refer to 

PB-13, "Parking Drum Brake"

.

SBR021A

B

: Refer to 

PB-13, "Parking Drum Brake"

.

JPFIB0008ZZ

Revision: November 2015

2016 JUKE

PB-12

< REMOVAL AND INSTALLATION >

PARKING BRAKE SHOE

• Adjuster for smoothness.

• Toggle lever and brake strut for excessive wear, damage and rust.

• Visually check inside of the drum for excessive wear, cracks, and damage with a pair of vernier calipers.

ADJUSTMENT AFTER INSTALLATION

1. Adjust the parking brake lever stroke. Refer to 

PB-4, "Inspection and Adjustment"

.

2. Rotate the disc rotor to check that there is no drag. Install the plug. If any drag is found, follow the proce-

dure described below.

a. Adjust parking brake stroke again.
b. Check rear disc brake. Refer to 

BR-67, "BRAKE CALIPER ASSEMBLY : Inspection"

.

3. Adjust the parking brake shoe. Refer to 

PB-5, "Adjustment"

.

Revision: November 2015

2016 JUKE

SERVICE DATA AND SPECIFICATIONS (SDS)

PB-13

< SERVICE DATA AND SPECIFICATIONS (SDS) 

C

D

E

G

H

I

J

K

L

M

A

B

PB

N

O

P

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Parking Drum Brake

INFOID:0000000012200172

Unit: mm (in)

Parking Brake Control

INFOID:0000000012200173

Item

Limit

Brake lining

1.5 (0.059)

Drum (disc of inner diameter)

 173 (6.81)

Item

Standard

Number of notches [under force of 196 N (20 kg, 44 lb)]

9 

−

 10 notches

Number of notches when brake warning lamp turns ON

1 notch

Revision: November 2015

2016 JUKE

PCS

PCS-1

ELECTRICAL & POWER CONTROL

C

D

E

F

G

H

I

J

K

L

B

SECTION 

PCS

A

O

P

N

CONTENTS

POWER CONTROL SYSTEM

IPDM E/R

PRECAUTION ...............................................

3

PRECAUTIONS ...................................................

3

Precautions for Removing Battery Terminal  .............

3

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

3

SYSTEM DESCRIPTION  ..............................

5

COMPONENT PARTS  ........................................

5

Component Parts Location ........................................

5

SYSTEM ..............................................................

6

RELAY CONTROL SYSTEM  ......................................

6

RELAY CONTROL SYSTEM : System Diagram ......

6

RELAY CONTROL SYSTEM : System Descrip-
tion ............................................................................

7

RELAY CONTROL SYSTEM : Fail-safe  ...................

8

POWER CONTROL SYSTEM  .....................................

9

POWER CONTROL SYSTEM : System Diagram ....

10

POWER CONTROL SYSTEM : System Descrip-
tion ..........................................................................

10

SIGNAL BUFFER SYSTEM  ......................................

10

SIGNAL BUFFER SYSTEM : System Diagram  ......

10

SIGNAL BUFFER SYSTEM : System Description ....

10

POWER CONSUMPTION CONTROL SYSTEM  .......

10

POWER CONSUMPTION CONTROL SYSTEM : 
System Diagram ......................................................

11

POWER CONSUMPTION CONTROL SYSTEM : 
System Description  .................................................

11

DIAGNOSIS SYSTEM (IPDM E/R) .....................

12

Diagnosis Description  .............................................

12

CONSULT Function (IPDM E/R) .............................

14

ECU DIAGNOSIS INFORMATION  ..............

17

IPDM E/R ...........................................................

17

Reference Value ......................................................

17

Fail-safe ...................................................................

23

DTC Index ...............................................................

24

WIRING DIAGRAM ......................................

26

IPDM E/R ...........................................................

26

Wiring Diagram ........................................................

26

DTC/CIRCUIT DIAGNOSIS  .........................

31

U1000 CAN COMM CIRCUIT  ...........................

31

Description ...............................................................

31

DTC Logic ................................................................

31

Diagnosis Procedure  ...............................................

31

B2098 IGNITION RELAY ON STUCK  ..............

32

Description ...............................................................

32

DTC Logic ................................................................

32

Diagnosis Procedure  ...............................................

32

B2099 IGNITION RELAY OFF STUCK  ............

34

Description ...............................................................

34

DTC Logic ................................................................

34

Diagnosis Procedure  ...............................................

34

POWER SUPPLY AND GROUND CIRCUIT  ....

36

Diagnosis Procedure  ...............................................

36

REMOVAL AND INSTALLATION ...............

37

IPDM E/R ...........................................................

37

Exploded View .........................................................

37

Removal and Installation  .........................................

37

POWER DISTRIBUTION SYSTEM

PRECAUTION ..............................................

39

PRECAUTIONS .................................................

39

Precautions for Removing Battery Terminal ............

39

Revision: November 2015

2016 JUKE