Content .. 400 401 402 403 ..

Nissan Juke (2016 year). Service Repair Manual - part 402

FSU-16

< REMOVAL AND INSTALLATION >

FRONT STABILIZER

• Install stabilizer clamp and stabilizer bush with notch (A) and slit

(B) faced forward of the vehicle (

• To install stabilizer clamp mounting bolt, follow the tightening

method and the numerical order shown below:

• To install stabilizer connecting rod (1), tighten the mounting nut

with the hexagonal part (A) on the stabilizer connecting rod side

fixed.

• Perform final tightening of bolts and nuts at the vehicle installation

position (rubber bushing), under unladen conditions with tires on

level ground.

• Perform inspection after installation. Refer to

FSU-13, "Inspection"

Inspection

INFOID:0000000012199126

INSPECTION AFTER REMOVAL

Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks

or damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

1. Check wheel alignment. Refer to

FSU-7, "Inspection"

2. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

JPEIA0058ZZ

Manual tightening

: 1

Temporary tightening

: 2

→

Final tightening (Specified torque)

: 4

→

: Vehicle front

JPEIA0245GB

JPEIA0252ZZ

Revision: November 2015

2016 JUKE

FRONT SUSPENSION MEMBER

FSU-17

< REMOVAL AND INSTALLATION >

FSU

FRONT SUSPENSION MEMBER

Exploded View

INFOID:0000000012199127

Removal and Installation

INFOID:0000000012199128

REMOVAL

1. Separate intermediate shaft from steering gear assembly. Refer to

ST-14, "Removal and Installation"

2. Remove tires with power tool. Refer to

WT-39, "Removal and Installation"

3. Remove front under cover.
4. Separate stabilizer connecting rod from strut assembly. Refer to

FSU-15, "Removal and Installation"

5. Separate steering outer socket from steering knuckle. Refer to

ST-17, "Removal and Installation"

6. Separate transverse link from steering knuckle. Refer to

FAX-11, "Exploded View"

(NISMO),

FAX-66,

"Exploded View"

(EXCEPT NISMO).

7. Remove rear torque rod.

• 2WD: Refer to

EM-64, "2WD : Removal and Installation"

• AWD: Refer to

EM-68, "AWD : Removal and Installation"

8. Set suitable jack under front suspension member.

CAUTION:

Check the stable condition when using a jack.

9. Remove member stay and rebound stopper.
10. Remove suspension member mounting bolts, insulator, and rebound stopper rubber.
11. Gradually lower the jack to remove front suspension member from vehicle body.

CAUTION:

Operate while checking that jack supporting status is stable.

NOTE:

Remove it with each component parts.

12. Remove component parts from front suspension member.
13. Perform inspection after removal. Refer to

FSU-13, "Inspection"

INSTALLATION

Note the following, and install in the reverse order of removal.

Front suspension member

Rebound stopper rubber

Insulator

Member stay

Rebound stopper

: N·m (kg-m, ft-lb)

JPEIA0271GB

Revision: November 2015

2016 JUKE

FSU-18

< REMOVAL AND INSTALLATION >

FRONT SUSPENSION MEMBER

• To install rebound stopper (1), insert it with the protrusion aligned

with the hole of member stay (2).

• To install member stay and mounting bolts of front suspension

member, temporarily tighten the bolts before tightening to the

specified torque, referring to the tightening method and the numer-

ical order shown below:

• Perform final tightening of bolts and nuts at the vehicle installation

position (rubber bushing), under unladen conditions with tires on level ground.

• Perform inspection after installation. Refer to

FSU-13, "Inspection"

Inspection

INFOID:0000000012199129

INSPECTION AFTER REMOVAL

Check front suspension member for cracks, wear or damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

1. Check wheel sensor harness for proper connector. Refer to

BRC-147, "FRONT WHEEL SENSOR :

Exploded View"

2. Check wheel alignment. Refer to

FSU-7, "Inspection"

3. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

JPEIA0248ZZ

Temporary tightening

: 1

→

Final tightening
(Specified torque)

: 3

→

: Vehicle front

JPEIA0249GB

Revision: November 2015

2016 JUKE

SERVICE DATA AND SPECIFICATIONS (SDS)

FSU-19

< SERVICE DATA AND SPECIFICATIONS (SDS)

FSU

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Alignment

INFOID:0000000012199130

Measure value under unladen*

conditions.

*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Ball Joint

INFOID:0000000012199131

Wheelarch Height

INFOID:0000000012199132

FOR USA MODELS

EXCEPT NISMO

Item

Standard

Axle type

2WD

AWD

Camber
Degree minute (Decimal degree)

Minimum

–1

′

(–1.16

)

Nominal

–0

′

(–0.42

)

Maximum

′

(0.33

)

Left and right difference*

–0

′

(–0.75

) - 0

′

(0.75

)

Caster
Degree minute (Decimal degree)

Minimum

′

(3.75

)

′

(3.84

)

Nominal

′

(4.50

)

′

(4.58

)

Maximum

′

(5.25

)

′

(5.33

)

Left and right difference*

–0

′

(–0.75

) - 0

′

(0.75

)

Kingpin inclination
Degree minute (Decimal degree)

Minimum

′

(10.67

)

Nominal

′

(11.42

)

Maximum

′

(12.16

)

Toe-in

Total toe-in
Distance

Minimum

0 mm (0.00 in)

Nominal

In 2 mm (In 0.08 in)

Maximum

In 4 mm (In 0.16 in)

Total toe-angle
Degree minute (Decimal degree)

Minimum

Out 0

′

″

(Out 0.03

)

Nominal

In 0

′

″

(In 0.17

)

Maximum

In 0

′

″

(In 0.36

)

Item

Standard

Swing torque

0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)

Measurement on spring balance

15.4 – 150.8 N (1.6 – 15.3 kg, 3.5 – 33.8 lb)

Axial end play

0 mm (0 in)

Item

Standard

Axle type

2WD

AWD

Transmission

M/T

CVT

Front (Hf)

734 mm (28.90 in)

735 mm (28.94 in)

734 mm (28.90 in)

Revision: November 2015

2016 JUKE

FSU-20

< SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

NISMO

Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

FOR CANADA MODELS

EXCEPT NISMO

Rear (Hr)

745 mm (29.33 in)

746 mm (29.37 in)

741 mm (29.17 in)

Item

Standard

Axle type

2WD

AWD

Transmission

M/T

CVT

SFA746B

Item

NISMO

NISMO RS

NISMO

NISMO RS

Axle type

2WD

AWD

Front (Hf)

724 mm (28.50 in)

725 mm (28.54 in)

724 mm (28.50 in)

Rear (Hr)

738 mm (29.06 in)

739 mm (29.09 in)

735 mm (28.94 in)

SFA746B

Item

Standard

Axle type

2WD

AWD

Transmission

M/T

CVT

Front (Hf)

735 mm (28.94 in)

Revision: November 2015

2016 JUKE

SERVICE DATA AND SPECIFICATIONS (SDS)

FSU-21

< SERVICE DATA AND SPECIFICATIONS (SDS)

FSU

Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

NISMO

Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.

Rear (Hr)

745 mm (29.33 in)

746 mm (29.37 in)

741 mm (29.17 in)

Item

Standard

Axle type

2WD

AWD

Transmission

M/T

CVT

SFA746B

Item

NISMO

NISMO RS

NISMO

NISMO RS

Axle type

2WD

AWD

Front (Hf)

727 mm (28.62 in)

725 mm (28.54 in)

726 mm (28.58 in)

724 mm (28.50 in)

Rear (Hr)

740 mm (29.13 in)

735 mm (28.94 in)

SFA746B

Revision: November 2015

2016 JUKE

A
B

QUICK REFERENCE INDEX

A GENERAL INFORMATION

General Information

B ENGINE

Engine Mechanical

Engine Lubrication System

Engine Cooling System

Engine Control System

Accelerator Control System

C ELECTRIC POWER TRAIN

HBC

Hybrid Control System

HBB

Hybrid Battery System

HBR

Hybrid Brake System

EVC

EV Control System

TMS

Traction Motor System

EVB

EV Battery System

Vehicle Charging System

HCO

High Voltage Cooling System

D TRANSMISSION & DRIVELINE

Clutch

Transaxle & Transmission

E SUSPENSION

SCS

Suspension Control System

Road Wheels & Tires

F BRAKES

Brake System

Parking Brake System

BRC

Brake Control System

G STEERING

Steering System

STC

Steering Control System

H RESTRAINTS

Seat Belt

SBC

Seat Belt Control System

SRS Airbag

SRC

SRS Airbag Control System

VENTILATION, HEATER & AIR
CONDITIONER

VTL

Ventilation System

Heater & Air Conditioning System

HAC

Heater & Air Conditioning Control System

J BODY INTERIOR

ADP

Automatic Drive Positioner

K BODY EXTERIOR, DOORS,

ROOF & VEHICLE SECURITY

DLK

Door & Lock

SEC

Security Control System

Glass & Window System

PWC

Power Window Control System

Hood

L DRIVER CONTROLS

MIR

Mirrors

EXL

Exterior Lighting System

INL

Interior Lighting System

VSP

Approaching Vehicle Sound for Pedestrians (VSP)

M ELECTRICAL & POWER CON-

TROL

PWO

Power Outlet

BCS

Body Control System

LAN

LAN System

PCS

Power Control System

CHG

Charging System

Power Supply, Ground & Circuit Elements

N DRIVER INFORMATION &

MULTIMEDIA

MWI

Meter, Warning Lamp & Indicator

WCS

Warning Chime System

Sonar System

Audio, Visual & Navigation System

O CRUISE CONTROL &

DRIVER ASSISTANCE

CCS

Cruise Control System

DAS

Driver Assistance System

DMS

Drive Mode System

P MAINTENANCE

Maintenance

Q INDEX

IDX

Alphabetical Index

All Rights Reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, recording or otherwise,
without the prior written per-
mission of NISSAN MOTOR
CO., LTD.

Edition: September 2015
Revision: November 2015
Publication No. SM16E00F15U1

FOREWORD

This manual contains maintenance and repair procedure for the 2016
NISSAN JUKE.

In order to assure your safety and the efficient functioning of the vehicle,
this manual should be read thoroughly. It is especially important that the
PRECAUTIONS in the GI section be completely understood before starting
any repair task.

All information in this manual is based on the latest product information
at the time of publication. The right is reserved to make changes in specifi-
cations and methods at any time without notice.

IMPORTANT SAFETY NOTICE

The proper performance of service is essential for both the safety of
the technician and the efficient functioning of the vehicle.
The service methods in this Service Manual are described in such a
manner that the service may be performed safely and accurately.
Service varies with the procedures used, the skills of the technician
and the tools and parts available. Accordingly, anyone using service
procedures, tools or parts which are not specifically recommended
by NISSAN must first be completely satisfied that neither personal
safety nor the vehicle’s safety will be jeopardized by the service
method selected.

Content .. 400 401 402 403 ..