Nissan Juke (2016 year). Service Repair Manual - part 128

AWD CONTROL MODULE

DLN-31

< ECU DIAGNOSIS INFORMATION >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

• When there is a difference of revolution speed between the front and rear wheel the shift occasionally

changes to direct 4-wheel driving conditions automatically. This is not a malfunction.

DTC Inspection Priority Chart

INFOID:0000000012199371

If some DTCs are displayed at the same time, perform inspections one by one based on the following priority

chart.

DTC Index

INFOID:0000000012199372

Priority

Detected items (DTC)

1

P182D SOLENOID LEFT

2

P182E SOLENOID RIGHT

3

P1813 4WD MODE SW

4

P183B SOL POWER SUPPLY

5

P1811 BATTERY VOLTAGE

6

P1808 VHCL SPEED SEN-ABS

7

P1829 THROTTLE POSI SEN

8

U1010 CONTROL UNIT (CAN)

9

U1000 CAN COMM CIRCUIT

10

P1809 CONTROL UNIT 4

11

P1830 ABS OP SIG

12

P1831 VDC OP SIG

13

P1832 TCS OP SIG

14

P183C DECEL G SENSOR

15

P183D SIDE G SENSOR

16

P183E YAWRATE SENSOR

17

P1865 GEAR RATIO

18

P1840 OUTPUT SPEED SIGNAL

19

P1864 INPUT SPEED SIGNAL

20

P181E STR ANGLE SEN

21

P1820 ENGINE SPEED SIG

22

P181D ENGINE SYSTEM

23

P183F GEAR POSI SIGNAL

24

P181B INCOMP SELF SHUT

25

P1804 CONTROL UNIT 3

26

P181F INCOMP CALIBRATION

DTC

Items (CONSULT screen items)

Reference

P1804

CONTROL UNIT 3

DLN-43, "DTC Logic"

P1808

VHCL SPEED SEN-ABS

DLN-44, "DTC Logic"

P1809

CONTROL UNIT 4

DLN-43, "DTC Logic"

P1811

BATTERY VOLTAGE

DLN-45, "DTC Logic"

P1813

4WD MODE SW

DLN-47, "DTC Logic"

P181B

INCOMP SELF SHUT

DLN-50, "DTC Logic"

P181D

ENGINE SYSTEM

DLN-52, "DTC Logic"

P181E

STR ANGLE SEN

DLN-53, "DTC Logic"

P181F

INCOMP CALIBRATION

DLN-54, "DTC Logic"

Revision: November 2015

2016 JUKE

DLN-32

< ECU DIAGNOSIS INFORMATION >

[TRANSFER: TY21B]

AWD CONTROL MODULE

NOTE:

If some DTCs are displayed at the same time, refer to 

DLN-31, "DTC Inspection Priority Chart"

.

P1820

ENGINE SPEED SIG

DLN-55, "DTC Logic"

P1829

THROTTLE POSI SEN

DLN-56, "DTC Logic"

P182D

SOLENOID LEFT

DLN-57, "DTC Logic"

P182E

SOLENOID RIGHT

DLN-60, "DTC Logic"

P1830

ABS OP SIG

DLN-63, "DTC Logic"

P1831

VDC OP SIG

DLN-64, "DTC Logic"

P1832

TCS OP SIG

DLN-65, "DTC Logic"

P183B

SOL POWER SUPPLY

DLN-66, "DTC Logic"

P183C

DECEL G SENSOR

DLN-68, "DTC Logic"

P183D

SIDE G SENSOR

DLN-69, "DTC Logic"

P183E

YAWRATE SENSOR

DLN-70, "DTC Logic"

P183F

GEAR POSI SIGNAL

DLN-71, "DTC Logic"

P1840

OUTPUT SPEED SIGNAL

DLN-72, "DTC Logic"

P1864

INPUT SPEED SIGNAL

DLN-73, "DTC Logic"

P1865

GEAR RATIO

DLN-74, "DTC Logic"

U1000

CAN COMM CIRCUIT

DLN-75, "DTC Logic"

U1010

CONTROL UNIT (CAN)

DLN-76, "DTC Logic"

DTC

Items (CONSULT screen items)

Reference

Revision: November 2015

2016 JUKE

AWD SYSTEM

DLN-33

< WIRING DIAGRAM >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

WIRING DIAGRAM

AWD SYSTEM

Wiring Diagram

INFOID:0000000012199373

JRDWC6642GB

Revision: November 2015

2016 JUKE

DLN-34

< WIRING DIAGRAM >

[TRANSFER: TY21B]

AWD SYSTEM

JRDWC6643GB

Revision: November 2015

2016 JUKE

AWD SYSTEM

DLN-35

< WIRING DIAGRAM >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

JRDWC6644GB

Revision: November 2015

2016 JUKE

DLN-36

< WIRING DIAGRAM >

[TRANSFER: TY21B]

AWD SYSTEM

JRDWC6645GB

Revision: November 2015

2016 JUKE

AWD SYSTEM

DLN-37

< WIRING DIAGRAM >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

JRDWC6646GB

Revision: November 2015

2016 JUKE

DLN-38

< BASIC INSPECTION >

[TRANSFER: TY21B]

DIAGNOSIS AND REPAIR WORK FLOW

BASIC INSPECTION

DIAGNOSIS AND REPAIR WORK FLOW

Work Flow

INFOID:0000000012199374

DETAILED FLOW

1.

INTERVIEW FROM THE CUSTOMER

Clarify customer complaints before inspection. First of all, perform an interview utilizing 

DLN-39, "Diagnostic

Work Sheet"

 and reproduce symptoms as well as fully understand it. Ask customer about his/her complaints

carefully. Check symptoms by driving vehicle with customer, if necessary.

CAUTION:

Customers are not professional. Never guess easily like “maybe the customer means that...,” or

“maybe the customer mentions this symptom”.

>> GO TO 2.

2.

CHECK SYMPTOM

Reproduce the symptom that is indicated by the customer, based on the information from the customer

obtained by interview. Also check that the symptom is not caused by protection function. Refer to 

DLN-30,

"Protection Function"

.

CAUTION:

When the symptom is caused by normal operation, fully inspect each portion and obtain the under-

standing of customer that the symptom is not caused by a malfunction.

>> GO TO 3.

3.

PERFORM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?

YES

>> Record or print self-diagnosis results. GO TO 4.

NO

>> GO TO 6.

4.

RECHECK SYMPTOM

With CONSULT

1. Erase self-diagnostic results for “ALL MODE AWD/4WD”.

2. Perform DTC confirmation procedures for the error detected system.

NOTE:

If some DTCs are detected at the same time, determine the order for performing the diagnosis based on 

DLN-

31, "DTC Inspection Priority Chart"

.

Is any DTC detected?

YES

>> GO TO 5.

NO

>> Check harness and connectors based on the information obtained by interview. Refer to 

GI-45,

"Intermittent Incident"

.

5.

REPAIR OR REPLACE ERROR-DETECTED PARTS

• Repair or replace error-detected parts.

• Reconnect part or connector after repairing or replacing.

• When DTC is detected, erase self-diagnostic results for “ALL MODE AWD/4WD”.

>> GO TO 7.

6.

IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS

Estimate error-detected system based on symptom diagnosis and perform inspection.
Can the error-detected system be identified?

Revision: November 2015

2016 JUKE