Nissan Juke F15. Manual - part 714

EXL-76

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

OPTICAL SENSOR

Is the inspection result normal?

YES

>> GO TO 8.

NO

>> Repair or replace harness.

8.

CHECK OPTICAL SENSOR SIGNAL CIRCUIT (SHORT)

Check continuity between optical sensor harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

Optical sensor

BCM

Continuity

Connector

Terminal

Connector

Terminal

M84

2

M68

14

Existed

Optical sensor

—

Continuity

Connector

Terminal

M84

2

Ground

Not existed

HAZARD SWITCH

EXL-77

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

HAZARD SWITCH

Component Function Check

INFOID:0000000012201661

1.

CHECK HAZARD SWITCH SIGNAL

With CONSULT

1. Turn ignition switch ON.

2. Select “FLASHER” of “BCM” using CONSULT.

3. Select “HAZARD SW” in “Data Monitor” mode.

4. With operating the hazard switch, check the monitor status.

Is the inspection result normal?

YES

>> Hazard switch circuit is normal.

NO

>> Refer to 

EXL-77, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012201662

1.

CHECK HAZARD SWITCH SIGNAL

1. Turn ignition switch OFF.

2. Disconnect hazard switch connector.

3. Check voltage between hazard switch connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)

1. Disconnect BCM connector.

2. Check continuity between hazard switch harness connector and BCM harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

Monitor item

Condition

Monitor status

HAZARD SW

Hazard switch

ON

On

OFF

Off

+

-

Voltage

(Approx.)

Hazard switch

Connector

Terminal

M45

2

Ground

12 V

Hazard switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

M45

2

M68

29

Existed

Hazard switch

—

Continuity

Connector

Terminal

M45

2

Ground

Not existed

EXL-78

< DTC/CIRCUIT DIAGNOSIS >

[XENON TYPE]

HAZARD SWITCH

NO

>> Repair or replace harness.

4.

CHECK HAZARD SWITCH GROUND CIRCUIT

Check continuity between hazard switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace hazard switch. Refer to 

EXL-107, "Removal and Installation"

.

NO

>> Repair or replace harness.

Hazard switch

—

Continuity

Connector

Terminal

M45

1

Ground

Existed

EXTERIOR LIGHTING SYSTEM SYMPTOMS

EXL-79

< SYMPTOM DIAGNOSIS >

[XENON TYPE]

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

SYMPTOM DIAGNOSIS

EXTERIOR LIGHTING SYSTEM SYMPTOMS

Symptom Table

INFOID:0000000012201663

EXCEPT FOR NISMO MODELS

Without Daytime Running Light System

NOTE:

Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any

DTC is detected.

Symptom

Possible cause

Inspection item

Headlamp (HI) is not turned 
ON

One side

• Fuse
• Headlamp (HI) power supply/

ground circuit

• Headlamp (HI) bulb
• Headlamp assembly
- Harness
• IPDM E/R

Headlamp (HI) circuit
Refer to 

EXL-50, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
 “BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to 

EXL-87, "Diagnosis Procedure"

.

High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]

Combination meter

• Combination meter

Data monitor “HI-BEAM IND”

• BCM (HEAD LAMP)

Active test “HEAD LAMP”

Headlamp (LO) is not 
turned ON

One side

• Fuse
• Headlamp (LO) power supply/

ground circuit

• Headlamp (LO) bulb

(Xenon bulb)

• Headlamp assembly
- HID control unit
- Xenon bulb socket
- Harness
• IPDM E/R

Headlamp (LO) circuit
Refer to 

EXL-53, "Component Func-

tion Check"

.

Both sides

Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to 

EXL-88, "Diagnosis Procedure"

.

Each lamp is not turned ON/OFF with lighting switch 
AUTO

• Combination switch input/output 

signal circuit

• Combination switch
• BCM

Combination switch
Refer to 

BCS-92, "Symptom Table"

.

• Optical sensor power supply/

ground/signal circuit

• Optical sensor
• BCM

Optical sensor
Refer to 

EXL-74, "Component Func-

tion Check"

.

Parking lamp is not turned ON

• Parking lamp power supply/

ground circuit

• Front combination lamp
- LED  (Parking  lamp)
- Harness
• IPDM E/R

Parking lamp circuit
Refer to 

EXL-56, "Component Func-

tion Check"

.

Front side marker lamp is not turned ON

• Front side marker lamp power 

supply/ground circuit

• Front side marker lamp bulb
• Front side marker lamp bulb sock-

et

Front side marker lamp circuit
Refer to 

EXL-58, "Component Func-

tion Check"

.