Nissan Juke F15. Manual - part 584

 

  Index      Nissan     Nissan Juke F15 (2015 year) - Service and Repair Manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  582  583  584  585   ..

 

 

Nissan Juke F15. Manual - part 584

 

 

P2127, P2128 APP SENSOR

EC-1149

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

NO

>> Repair or replace error-detected parts.

3.

CHECK APP SENSOR 2 GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT

1. Check the continuity between APP sensor harness connector and ECM harness connector.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace error-detected parts

5.

CHECK APP SENSOR

Check the APP sensor. Refer to 

EC-1149, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-4, "Exploded View"

.

Component Inspection

INFOID:0000000012198674

1.

CHECK ACCELERATOR PEDAL POSITION SENSOR

1. Turn ignition switch OFF.

2. Reconnect all harness connectors disconnected.

3. Turn ignition switch ON.

4. Check the voltage between ECM harness connector terminals as per the following condition.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-4, "Exploded View"

.

+

−

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E101

1

E19

144

Existed

+

−

Continuity

APP sensor

ECM

Connector

Terminal

Connector

Terminal

E101

6

E19

143

Existed

ECM

Condition

Voltage

Connector

+

−

Terminal

E19

150

151

Accelerator pedal

Fully released

0.6 - 0.9 V

Fully depressed

3.9 - 4.7 V

143

144

Fully released

0.3 - 0.6 V

Fully depressed

1.95 - 2.4 V

EC-1150

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2135 TP SENSOR

P2135 TP SENSOR

DTC Logic

INFOID:0000000012198675

DTC DETECTION LOGIC

NOTE:

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to

EC-1060, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure

before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-1150, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012198676

1.

CHECK THROTTLE POSITION SENSOR POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect electric throttle control actuator harness connector.

3. Turn ignition switch ON.

4. Check the voltage between electric throttle control actuator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between electric throttle control actuator harness connector and ground.

DTC No.

Trouble diagnosis name

(Trouble diagnosis con-

tent)

DTC detecting condition

Possible cause

P2135

TP SENSOR-B1
(Throttle position sensor 
circuit range/perfor-
mance)

Rationally incorrect voltage is sent to ECM 
compared with the signals from TP sensor 1 
and TP sensor 2.

• Harness or connector

(TP sensor 1 or 2 circuit is open or shorted.)

• Electric throttle control actuator

(TP sensor 1 or 2)

+

−

Voltage

(Approx.)

Electric throttle control actuator

Connector

Terminal

F29

5

Ground

5 V

P2135 TP SENSOR

EC-1151

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

4. Also check harness for short to ground.
Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

3.

CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between electric throttle control actuator harness connector and ECM harness con-

nector.

4. Also check harness for short to power.
Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace error-detected parts.

4.

CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT

1. Check the continuity between electric throttle control actuator harness connector and ECM harness con-

nector.

2. Also check harness for short to ground and to power.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

5.

CHECK THROTTLE POSITION SENSOR

Check the throttle position sensor. Refer to 

EC-1151, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Replace electric throttle control actuator. Refer to 

EM-197, "Exploded View"

.

Component Inspection

INFOID:0000000012198677

1.

CHECK THROTTLE POSITION SENSOR

1. Turn ignition switch OFF.

2. Reconnect all harness connectors disconnected.

+

−

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F29

5

F24

83

Existed

+

−

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F29

4

F24

85

Existed

+

−

Continuity

Electric throttle control actu-

ator

ECM

Connector

Terminal

Connector

Terminal

F29

6

F24

88

Existed

3

80

EC-1152

< DTC/CIRCUIT DIAGNOSIS >

[MR EXCEPT FOR NISMO RS MODELS]

P2135 TP SENSOR

3. Perform “ Throttle Valve Closed Position Learning”. Refer to 

EC-754, "Description"

.

4. Turn ignition switch ON.

5. Set selector lever to D (CVT) or 1st (M/T) position. 

6. Check the voltage between ECM harness connector terminals as per the following conditions.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace electric throttle control actuator. Refer to 

EM-197, "Exploded View"

.

ECM

Condition

Voltage

Connector

+

−

Terminal

F24

88

85

Accelerator 
pedal

Fully released

More than 0.36V

Fully depressed

Less than 4.75V

80

Fully released

Less than 4.75V

Fully depressed

More than 0.36V

 

 

 

 

 

 

 

Content   ..  582  583  584  585   ..