Nissan Juke F15. Manual - part 223

DLK-72

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DOOR LOCK ACTUATOR

Is the inspection result normal?

YES

>> Door lock actuator is OK.

NO

>> Refer to 

DLK-68, "DRIVER SIDE : Diagnosis Procedure"

.

REAR RH : Diagnosis Procedure

INFOID:0000000012196634

1.

CHECK DOOR LOCK ACTUATOR INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect rear door lock assembly RH connector.

3. Check voltage between rear door lock assembly RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear door lock assembly RH.

NO

>> GO TO 2.

2.

CHECK DOOR LOCK ACTUATOR CIRCUIT

1. Disconnect BCM connector and all door lock assembly connector.

2. Check continuity between BCM harness connector and rear door lock assembly RH harness connector. 

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK BCM OUTPUT SIGNAL

1. Connect BCM connector.

2. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Check for internal short of each door lock actuator.

NO

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

(+)

(–)

Condition

Voltage

(Approx.)

Rear door lock assembly RH

Connector

Terminal

D45

6

Ground

Door lock and unlock switch

Unlock

12 V

5

Lock

BCM

Rear door lock assembly RH

Continuity 

Connector

Terminal

Connector

Terminal

B10

55

D45

6

Existed

M69

65

5

BCM

Ground

Continuity 

Connector

Terminal

B10

55

Not existed

M69

65

(+)

(–)

Condition

Voltage

(Approx.)

BCM

Connector

Terminal

B10

55

Ground

Door lock and unlock switch

Unlock

12 V

M69

65

Lock

DOOR LOCK AND UNLOCK SWITCH

DLK-73

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR LOCK AND UNLOCK SWITCH

Component Function Check

INFOID:0000000012196635

1.

CHECK FUNCTION

1. Select “DOOR LOCK” of “BCM” using CONSULT.

2. Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock and unlock switch is OK.

NO

>> Refer to 

DLK-73, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196636

1.

CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check signal between power window main switch harness connector and ground using oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT

1. Disconnect BCM connector and power window main switch connector.

2. Check continuity between BCM harness connector and power window main switch harness connector.

3. Check continuity between BCM harness connector and ground.

Monitor item

Condition

Status

CDL LOCK SW 

Door lock and unlock switch

Lock

ON

Unlock

OFF

CDL UNLOCK SW 

Lock

OFF

Unlock

ON

(+)

(–)

Signal

(Reference value)

Power window main switch

Connector

Terminal 

D35

3

Ground

1.0 - 1.5 V

15

JPMIA0012GB

BCM

Power window main switch

Continuity 

Connector

Terminal

Connector

Terminal

M68

12

D35

3

Existed

13

15

DLK-74

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

DOOR LOCK AND UNLOCK SWITCH

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR LOCK AND UNLOCK SWITCH GROUND 

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DOOR LOCK AND UNLOCK SWITCH

Refer to 

DLK-74, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace power window main switch. Refer to 

PWC-54, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000012196637

1.

CHECK DOOR LOCK AND UNLOCK SWITCH

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check continuity between power window main switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace power window main switch.

BCM

Ground

Continuity

Connector

Terminal

M68

12

Not existed

13

Power window main switch

Ground

Continuity 

Connector

Terminal

D35

1

Existed

Power window main switch

Condition

Continuity

Terminal

3

1

Door lock and unlock 
switch

LOCK

Existed

UNLOCK

Not existed

15

LOCK

Not existed

UNLOCK

Existed

DOOR REQUEST SWITCH

DLK-75

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR REQUEST SWITCH

Component Function Check

INFOID:0000000012196638

1.

CHECK FUNCTION

1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.

2. Select “REQ SW-DR”, “REQ SW-AS” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Front door request switch is OK.

NO

>> Refer to 

DLK-75, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000012196639

1.

CHECK DOOR REQUEST SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect malfunctioning front door request switch connector.

3. Check voltage between malfunctioning front door request switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR REQUEST SWITCH CIRCUIT

1. Disconnect BCM connector.

2. Check continuity between malfunctioning front door request switch harness connector and BCM harness

connector.

3. Check continuity between malfunctioning front door request switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-94, "Removal and Installation"

.

NO

>> Repair or replace harness.

Monitor item

Condition

Status

REQ SW -DR

Driver side door request switch

Pressed

ON

Released

OFF

REQ SW -AS

Passenger side door request switch

Pressed

ON

Released

OFF

(+)

(–)

Voltage

(Approx.)

Front door request switch

Connector

Terminal

Driver side

D34

2

Ground

12 V

Passenger side

D15

1

Front door request switch

BCM

Continuity 

Connector

Terminal

Connector

Terminal

Driver side

D34

2

M70

75

Existed

Passenger side

D15

1

100

Front door request switch

Ground

Continuity 

Connector

Terminal

Driver side

D34

2

Not existed

Passenger side

D15

1