Nissan Juke F15. Manual - part 1330

TM-510

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0962 PRESSURE CONTROL SOLENOID A

NO

>> There is malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to 

TM-

577, "Removal and Installation"

.

P0963 PRESSURE CONTROL SOLENOID A

TM-511

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0963 PRESSURE CONTROL SOLENOID A

DTC Logic

INFOID:0000000012201210

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine and wait for 5 seconds or more.

2. Check the first trip DTC.
Is “P0963” detected?

YES

>> Go to 

TM-511, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012201211

1.

CHECK CIRCUIT BETWEEN TCM AND CVT UNIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector and CVT unit connector.

3. Check continuity between TCM harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK CIRCUIT BETWEEN CVT UNIT AND GROUND

Check continuity between CVT unit harness connector terminal and ground. 

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0963

PC SOLENOID A
(Pressure Control Solenoid A 
Control Circuit High)

When all of the following conditions are satis-
fied and this state is maintained for 0.2 sec-
onds:
• TCM power supply voltage: More than 11 V
• P0962 is not detected
• TCM judges that solenoid valve circuit is 

open. 

• Harness or connector

(Line pressure solenoid valve circuit is 
open or shorted to power supply)

• Line pressure solenoid valve

TCM

CVT unit

Continuity

Connector

Terminal

Connector

Terminal

F83

30

F82

1

Existed

CVT unit

—

Condition

Resistance

Connector

Terminal

F250

1

Ground

CVT fluid temperature: 20

°C (68°F)

5.5 – 7.0 

Ω

CVT fluid temperature: 50

°C (122°F)

6.0 – 8.0 

Ω

CVT fluid temperature: 80

°C (176°F)

6.5 – 8.5 

Ω

TM-512

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

P0963 PRESSURE CONTROL SOLENOID A

NO

>> There is malfunction of line pressure solenoid valve. Replace transaxle assembly. Refer to 

TM-

577, "Removal and Installation"

.

P0965 PRESSURE CONTROL SOLENOID B

TM-513

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0965 PRESSURE CONTROL SOLENOID B

DTC Logic

INFOID:0000000012201212

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

Possible causes

P0965

PC SOLENOID B
(Pressure Control Solenoid B 
Control Circuit Range Perfor-
mance)

When any of 1 or 2 is satisfied and this state is 
maintained for 10 seconds:
1.

When all of the following conditions are 
satisfied:

-

DTC other than the applicable DTC is not 
detected.

-

Engine speed: More than 625 rpm

-

Selector lever: Other than P/N position

-

CVT fluid temperature: More than -20

°C 

(-4

°F)

-

TCM power supply: More than 11 V

-

The difference between instruction pres-
sure of primary pressure and 10-msec-
ago instruction primary pressure is 0 
MPa or more

-

Instruction pressure of primary pressure: 
0.86 MPa or more

-

Instruction pressure of primary pressure 
- primary pressure: More than 1.2 MPa

-

When all of the following conditions are 
satisfied and this state is maintained for 
1 second:

•

DTC other than the applicable DTC is not 
detected.

•

CVT fluid temperature: More than -20

°C 

(-4

°F)

•

Selector lever: Other than P/N position

•

Engine speed: More than 625 rpm

•

Instruction pressure of primary pressure: 
More than 2 MPa

•

Primary pressure: 0.4 MPa or less

2.

When all of the following conditions are 
satisfied:

-

DTC other than the applicable DTC is not 
detected.

-

CVT fluid temperature: More than -20

°C 

(-4

°F)

-

Selector lever: Other than P/N position

-

TCM power supply: More than 11 V

-

When all of the following conditions are 
satisfied and this state is maintained for 
5.5 seconds:

•

DTC other than the applicable DTC is not 
detected.

•

CVT fluid temperature: More than -20

°C 

(-4

°F)

•

Selector lever: Other than P/N position

•

Primary pressure - instruction pressure 
of primary pressure: 1.2 MPa or more

-

The difference between instruction pres-
sure of primary pressure and 10-msec-
ago instruction primary pressure is 0 
MPa or more

-

Primary pressure - instruction pressure 
of primary pressure: More than 1.2 MPa

• Harness or connector

(Primary pressure solenoid valve cir-
cuit is open or shorted.)

• Primary pressure solenoid valve