Mitsubishi Outlander XL. Manual - part 208

OBD- II DRIVE CYCLE

All kinds of diagnostic trouble codes (DTCs) can be
monitored by carrying out a short drive according to
the following 24 drive cycle patterns. In other words,
doing  such  a  drive  regenerates  any  kind  of  trouble
which involves illuminating the Malfunction Indicator
Lamp  (SERVICE  ENGINE  SOON  or  Check  Engine
Lamp)  and  verifies  the  repair  procedure  has
eliminated [the trouble the Malfunction Indicator Lamp
(SERVICE ENGINE SOON or Check Engine Lamp)
is no longer illuminated].

Two technicians should always be in the vehicle
when carrying out a test.

NOTE: 

Check that the diagnosis trouble code (DTC)

is not output before driving the OBD-II drive
cycle. Erase the DTC if it has been output.

NOTE: 

Drive cycle patterns are not established

for Power steering pressure sensor monitor (DTC

P0551), and Fuel level sensor monitor (DTC P0461,
P2066). Please reference the M.U.T. data list to
judge whether these monitor items are normal.

 

DRIVE CYCLE PATTERN LIST

MONITOR ITEM

DIAGNOSTIC  TROUBLE
CODE (DTC)

PATTERN

Heated oxygen sensor (front) monitor Readiness test item

P0133, P0153

1

Heated oxygen sensor heater monitor Readiness test item

P0031,  P0032,  P0037,
P0038,  P0051,  P0052,
P0057, P0058

2

Center exhaust pipe heated oxgen sensor heater monitor

P0043, P0044

Exhaust gas recirculation (EGR) system monitor Readiness
test item

P0401, P0489, P0490

3

Catalytic converter monitor Readiness test item

P0421, P0431

4

Evaporative  emission  system  leak  monitor  (small  leak  and
gross leak) Readiness test item

P0442, P0455

5

Evaporative purge system monitor

P0441

Fuel tank pressure sensor monitor

P0450

Evaporative emission system leak monitor (very small leak)
Readiness test item

P0456

6

Mass airflow sensor monitor

P0101

7

Manifold absolute pressure (MAP) sensor monitor

P0106, P0107

Intake air temperature sensor monitor

P0111

8

Engine coolant temperature sensor monitor

P0116, P0125

9

Thermostat monitor

P0128

10

Heated oxygen sensor (rear) monitor <Readiness test item> P0139, P0159

11

Center exhaust pipe heated oxgen sensor monitor

P0145

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

13Ab-27

DIAGNOSTIC FUNCTION

MONITOR ITEM

DIAGNOSTIC  TROUBLE
CODE (DTC)

PATTERN

HC adsorber (HC trap catalyst) monitor

P2423

Air fuel ratio feedback monitor

P0134, P0154

12

Heated oxygen sensor (rear) monitor

P0140, P0160

13

Center exhaust pipe heated oxgen sensor monitor

P0146

Fuel tank temperature sensor monitor

P0181

14

Misfire monitor

P0300,  P0301,  P0302,
P0303,  P0304,  P0305,
P0306

15

Fuel tank pressure sensor monitor

P0451

16

Throttle position sensor plausibility monitor

P1233, P1234

17

Mass airflow sensor plausibility monitor

P1235, P1238

Torque monitor

P1241

DOR radiator tampering monitor

P1543, P1547

18

DOR radiator tampering monitor

P1544, P1545, P1546

19

Idle speed control system monitor

P0506, P0507

20

MIVEC system monitor

P1020

21

Fuel trim monitor

P0171,  P0172,  P0174,
P0175

22

Heated oxygen sensor monitor

P0131,  P0137,  P0143,
P0151,  P0157,  P2195,
P2197

23

Mass airflow sensor monitor

P0102, P0103

24

Manifold absolute pressure (MAP) sensor monitor

P0108

Intake air temperature sensor monitor

P0112, P0113

Engine coolant temperature sensor monitor

P0117, P0118

Heated oxygen sensor monitor

P0132,  P0138,  P0144,
P0152,  P0158,  P2252,
P2253

Fuel tank temperature sensor monitor

P0182, P0183

Injector monitor

P0201,  P0202,  P0203,
P0204, P0205, P0206

Crankshaft position sensor monitor

P0335

Camshaft position sensor monitor

P0340

Evaporative emission purge solenoid monitor

P0443

Evaporative emission ventilation solenoid monitor

P0446

Fuel tank pressure sensor monitor

P0452, P0453

Fuel level sensor monitor

P0462, P0463

Power steering pressure sensor monitor

P0552, P0553

Engine oil control valve monitor

P1021, P1023

Engine RPM plausibility monitor

P1239

13Ab-28

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

DIAGNOSTIC FUNCTION

MONITOR ITEM

DIAGNOSTIC  TROUBLE
CODE (DTC)

PATTERN

Barometric pressure sensor monitor

P2228, P2229

 

PATTERN 1

Drive

 cycle

pattern

ZK603451

(2)

(1)

(3)

4 minutes

During the monitor

1,300 - 3,500 r/min

Ignition
switch:
"lock" (off)

Engine speed

AA00

Time

Inspection
conditions

｠

Engine coolant temperature: More than 82°C (180°F)

｠

Intake air temperature: More than -10°C (14°F)

｠

Barometric pressure: More than 76 kPa (22.5 inHg)

｠

Condition of A/T: Selector lever "D" range

Test
procedure

1.

Start the engine with all the accessories switched OFF.

2.

Drive the vehicle for 4 minutes at the following conditions. (During the monitor)

NOTE: 

When the system is normal, the monitor is completed earlier.

｠

Vehicle speed: More than 30 km/h (19 mph)

｠

Engine speed: More than 1,300 r/min, less than 3,500 r/min

｠

Engine load: More than 30%, less than 60%

｠

Without rapid accelerator pedal movement

3.

Stop the vehicle at the safe place and turn the ignition switch to "LOCK" (OFF) position.

4.

Start the engine and do Steps 1 to 3 again.

NOTE: 

When the vehicle is operating normally and the OBD-II Drive Cycle is carried

out, the Readiness Codes will be set as "Complete" on the first drive cycle. The
second drive cycle is required to set the Readiness Codes as "Complete" if a fault
is detected during the first drive cycle.

5.

Confirm that the diagnostic trouble code (DTC) is not output.

 

PATTERN 2

Test
procedure

1.

Start the engine with all the accessories switched OFF.

2.

Let the engine idle for 10 seconds. (During the monitor)

3.

Turn the ignition switch to the "LOCK" (OFF) position.

4.

Start the engine and do Steps 1 to 3 again.

NOTE: 

When the vehicle is operating normally and the OBD-II Drive Cycle is carried

out, the Readiness Codes will be set as "Complete" on the first drive cycle. The

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

13Ab-29

DIAGNOSTIC FUNCTION

second drive cycle is required to set the Readiness Codes as "Complete" if a fault
is detected during the first drive cycle.

5.

Confirm that the diagnostic trouble code (DTC) is not output.

 

PATTERN 3

Drive

 cycle

pattern

ZK603452

(2)

(1)

(3)

90 seconds

Ignition 
switch: 
"lock" (off)

During the monitor

60 km/h
(38 mph)

Vehicle speed

AA00

30 km/h
(18mph)

(4)

(5)

(6)

20 seconds

Time

During the monitor

Inspection
conditions

｠

Engine coolant temperature: More than 82°C (180°F)

｠

Intake air temperature: More than 5°C (41°F)

｠

Barometric pressure: More than 76 kPa (22.5 inHg)

｠

Condition of A/T: Selector lever "D" range

Test
procedure

1.

Start the engine with all the accessories switched OFF.

2.

Accelerate until the vehicle speed is 60 km/h (38 mph) and then drive the vehicle for 90
seconds.

3.

Release the accelerator pedal and reduce vehicle speed to 30 km/h (18 mph). (During the
monitor)

4.

Accelerate until the vehicle speed is 60 km/h (38 mph) and then drive the vehicle for 20
seconds.

5.

Release the accelerator pedal and reduce vehicle speed to 30 km/h (18 mph). (During the
monitor)

6.

Stop the safe place and turn the ignition switch to "LOCK" (OFF) position.

7.

Start the engine and do Steps 1 to 6 again.

NOTE: 

When the vehicle is operating normally and the OBD-II Drive Cycle is carried

out, the Readiness Codes will be set as "Complete" on the first drive cycle. The
second drive cycle is required to set the Readiness Codes as "Complete" if a fault
is detected during the first drive cycle.

8.

Confirm that the diagnostic trouble code (DTC) is not output.

 

13Ab-30

MULTIPORT INJECTION SYSTEM (MFI) <DIAGNOSIS>

DIAGNOSTIC FUNCTION