Mitsubishi Outlander GS45X. Manual - part 1737

DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>

TSB Revision

AUTOMATIC TRANSAXLE

23C-253

STEP 7. M.U.T.-III data list
Check the following data list. (Refer to 

P.23C-254

).

• Item No.8: Steering angle sensor

• Item No.21: Wheel speed sensor <FL>

• Item No.22: Wheel speed sensor <FR>

• Item No.23: Wheel speed sensor <RL>

• Item No.24: Wheel speed sensor <RR>

• Item No.25: Yaw rate sensor

• Item No.26: Lateral G sensor

Q: Is the check result normal?

YES : Go to Step 8.
NO :  Perform the troubleshooting for the ASC. (Refer to 

GROUP 35C 

− Troubleshooting 

P.35C-18

). Then go 

to Step 9.

STEP 8. Retest the system.
Q: Is the check result normal?

YES : Intermittent malfunction. (Refer to GROUP 00 

− How 

to Cope with Intermittent Malfunction 

P.00-15

).

NO :  Replace the AWC-ECU. (Refer to 

P.23C-295

). Then 

go to Step 9.

STEP 9. Retest the system.
Q: Is the check result normal?

YES : This diagnosis is complete.
NO :  Return to Step 1.

DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>

TSB Revision

AUTOMATIC TRANSAXLE

23C-254

DATA LIST REFERENCE TABLE

M1235004600019

Item 
No.

Display on M.U.T.-III

Check conditions

Normal condition

1

S-AWC control mode

NORMAL is selected (displayed on 
multi information display).

NORMAL

SNOW is selected (displayed on multi 
information display).

SNOW

OFF ROAD is selected (displayed on 
multi information display).

OFF ROAD

2

Longitudinal drive force (Meter)

Perform a test run of the vehicle.

0 

− 5segment

3

Lateral drive force (Meter)

Perform a test run of the vehicle.

-5 

− 5segment

4

Front coupling torque

Perform a test run of the vehicle.

The torque changes

5

center coupling torque

Perform a test run of the vehicle.

The torque changes

6

S-AWC protection control

The S-AWC control mode on the multi 
information display flashes.

ON

Other than above

OFF

7

S-AWC system fail

The trouble is displayed to the multi 
information display.

ON

Other than above

OFF

8

Steering angle sensor

Steering wheel: Steered 90

° to right

+90 deg

Steering wheel: Steered 90

° to left

−90 deg

9

Steering angle speed

Steering wheel: Without steering 
wheel operation

0 deg/s

Steering wheel: With steering wheel 
operation

Changes depending 
on the turning 
speed.

10

Steering angle sensor (status)

Normal

Correct

Faulty

Malfunction

Neutral point not learned

Neutral not learned

Neutral point not learned or failed

Neutral not learned 
and Malfunction

11

Accelerator position

Release the accelerator pedal

Approximately 0%

Depress the accelerator pedal

0 

− 100%

Accelerator pedal fully opened

Approximately 
100%

12

Engine speed

Idling and test run

Nearly the same as 
the tachometer 
display

13

Engine torque (Driver request)

Perform a test run of the vehicle.

The torque changes

14

Engine torque (Effective)

Perform a test run of the vehicle.

The torque changes

DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>

TSB Revision

AUTOMATIC TRANSAXLE

23C-255

15

A/T gear position

Gear range: P

P

Gear range: R

R

Gear range: N

N

Gear range: 1st

1st

Gear range: 2nd

2nd

Gear range: 3rd

3rd

Gear range: 4th

4th

Gear range: 5th

5th

Gear range: 6th

6th

16

T/M oil temperature

Driving after engine has warmed up

Gradually 
increases.

17

FL wheel speed (raw value)

− (reference because of r/min)

−

18

FR wheel speed (raw value)

19

RL wheel speed (raw value)

20

RR wheel speed (raw value)

21

FL wheel speed sensor

Perform a test run of the vehicle.

Nearly the same as 
the speedometer 
display

22

FR wheel speed sensor

23

RL wheel speed sensor

24

RR wheel speed sensor

25

Yaw rate sensor

When the vehicle is stationary

Approximately 0 
deg/s

Perform a test run of the vehicle.

−90 − 90 deg/s

26

Lateral G sensor

Vehicle is stopped (horizontal state).

−1.1 − 1.1 m/s

2

Perform a test run of the vehicle.

−10 − 10 m/s

2

27

Longitudinal G sensor

Vehicle is stopped (horizontal state).

−1.1 − 1.1 m/s

2

Perform a test run of the vehicle.

−10 − 10 m/s

2

28

Brake switch (CAN input)

Brake pedal: Depressed

ON

Brake pedal: Released

OFF

29

Parking brake SW (CAN input)

Parking brake lever: Pulled

ON

Parking brake lever: Released

OFF

30

Ignition SW (CAN input)

Ignition switch: ON

ON

Ignition switch: START

START

31

Battery voltage (CAN input)

Ignition switch: ON

System voltage

32

IOD fuse (CAN input)

Fuse inserted

ON

Fuse removed

OFF

33

Odometer (CAN input)

Ignition switch: ON

The same as the 
meter display

34

Ambient temperature (CAN input)

Ignition switch: ON

The same as the 
meter display

Item 
No.

Display on M.U.T.-III

Check conditions

Normal condition

DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>

TSB Revision

AUTOMATIC TRANSAXLE

23C-256

SPECIAL FUNCTION

M1235004700016

RESET

35

Ignition off time (CAN input)

After ignition switch: OFF for one 
minute or more, ignition switch: ON

The same value as 
the last ignition 
switch : OFF time 
(min display)

36

ETACS coding status

Coding incomplete

Not complete

Coding data requested

Data request

Coding completed

Complete

37

T/M type (CAN input)

Always

Transaxle type is 
the same as the 
vehicle.

38

IG1

ON

ON

OFF

OFF

39

ECU power supply voltage

Ignition switch: ON

10 

− 16 V

40

Output load voltage

Ignition switch: ON

10 

− 16 V

41

SW1 status

S-AWC control mode selector: 
NORMAL

ON

S-AWC control mode selector : Other 
than above

OFF

42

SW2 status

S-AWC control mode selector: OFF 
ROAD

ON

S-AWC control mode selector : Other 
than above

OFF

43

Yaw rate sensor (adjusted value)

Ignition switch: ON

−6 − 6 deg/s

44

SAS (adjusted value)

Ignition switch: ON

−15 − 15 deg

45

Chassis Number writing counter

Ignition switch: ON

Writing count

46

Chassis Number (original) lock

Ignition switch: 
ON

Locked

Lock

Unlocked

Unlock

47

Mileage counter

Ignition switch: ON

Counter value

48

Coding counter

Ignition switch: ON

Coding count

Item 
No.

Display on M.U.T.-III

Check conditions

Normal condition

Item 
No.

Display on M.U.T.-III

Initialization contents

1

SAS adjusted value

Resets the steering wheel sensor neutral position learned value.

2

Front coupling estimated temp.

Reset the estimated temperature of front coupling and transfer.

3

center coupling estimated temp.

Reset the estimated temperature of center coupling.