Mitsubishi Lancer Evolution IX. Manual - part 110

 

  Index      Mitsubishi     Mitsubishi Lancer Evolution IX - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  108  109  110  111   ..

 

 

Mitsubishi Lancer Evolution IX. Manual - part 110

 

 

GENERAL INFORMATION

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-3

Key reminder function

When the driver's door is opened with the ignition 
key inserted to the ignition cylinder and the door is 
locked (when the lock switch turns ON after turning 
OFF the unlock switch in the driver's door lock actua-
tor), after approximately 0.3 second, ETACS-ECU 
turns ON the unlock relay output for 0.25 second to 
discourage the door lock operation so that the igni-
tion key left in the ignition cylinder is prevented.
If the discouraging the door lock operation fails, the 
current supply will be retried (The unlock relay output 
is turned ON for 0.25 second up to five times with 
one second interval).
NOTE: The broken line in the graph indicates the 
current supply retry state if the discouraging door 
lock operation fails.

DOOR UNLOCK FUNCTION WITH THE 
IMPACT DETECTION

If the vehicle crashed with the ignition switch ON or 
30 seconds after turning the ignition switch to LOCK 
(OFF), and the impact sensor detects an impact 
greater than the predetermined value, the impact 
sensor sends the signal to ETACS-ECU. Then, 
within the 0.1 second, ETACS-ECU energizes the 
unlock relay for one second for releasing the door 
lock to prevent passengers to be kept inside the 
vehicle after the crash.

NOTE: The fail safe disables the operation under the 
following conditions (Diagnosis code No.31 or 32 is 
set). Turn ON the ignition switch again after turning 
the ignition switch to LOCK (OFF) to return from the 
fail safe state.

.

No.31: When the ignition switch is ON, and the 
sensor shows under the short circuit voltage for 
2.5 second

No.32: When the ignition switch is ON, and the 
sensor shows over the closed circuit voltage for 
0.4 second

KEYLESS ENTRY SYSTEM
KEYLESS ENTRY HAZARD LAMP 
ANSWERBACK FUNCTION (THE INITIAL 
CONDITION: WITH FUNCTION OF 
LOCK/UNLOCK)

AC101499

ON

OFF

ON

OFF

(Open) ON

(Closed) OFF

(Key inserted) ON

Key reminder 
switch

Driver's door
switch

Driver's door actuator 
switch

Lock relay

Unlock relay

t: 0.3 seconds
T1: 0.25 seconds
T2: 1 second

(Key removed) OFF

LOCK

UNLOCK

t

t

t

t

t

T1

T1

T1

T1

T1

T1

T1

T1

T2

T2

T2

T2

AB

AC101500AB

ON

OFF

OFF

ON

OFF

LOCK

UNLOCK

Illuminate

Extinguish

Keyless entry
transmitter

Lock relay output

Unlock relay output

Hazard
warning light

GENERAL INFORMATION

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-4

The hazard answerback function that allows check-
ing the lock/unlock state of the door easily even in 
the daytime is adopted. When the lock signal from 
the keyless entry transmitter is received into 
ETACS-ECU, all doors are locked, and the hazard 
warning lamps blink twice. When the unlock signal is 
received, all doors are unlocked, and the hazard 
warning lamps blink once.
NOTE: The answerback blink time can be adjusted 
by the adjusting function.

KEYLESS ENTRY INTERIOR LAMP 
ANSWERBACK FUNCTION

The interior lamp blinks two times while locking the 
door for easy checking the keyless entry function. 
When the door is unlocked, the lamp lamps on for 15 
seconds (100%), and turns off.

TIMED LOCKING MECHANISM

After unlocking the doors with the keyless entry 
transmitter, if no doors are opened, if the ignition key 
is not inserted or if the locking function is not oper-
ated, the ETACS-ECU automatically locks the doors 
in 30 seconds.

WINDSHIELD WIPER AND WASHER
Intermittent control (the initial condition: with function)

ETACS-ECU calculates the intermittent time TI from 
the windshield intermittent wiper volume of the col-
umn switch and the vehicle speed calculated from 
the vehicle speed signals (vehicle speed sensor), 
and sends it to the front ECU as SWS data.

NOTE: The vehicle speed-dependent wiper function 
can be invalidated by the adjusting function.

AC304773

15 seconds

100 %

0 %

65 %

OFF

UNLOCK

LOCK

Lock/unlock 
signal by 
keyless entry

Interior lamp 
brightness

AB

AC304771

Intermittent wiper volume position

FAST

AB

100

0

Intermittent time: 
TI (sec.)

18

0

18

SLOW

Intermittent time: 
TI (sec.)

Vehicle speed (km/h)

Intermittent wiper volume 
"SLOW" position

Intermittent wiper volume 
"FAST" position

GENERAL INFORMATION

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-5

The front ECU determines the intermittent time TI 
from the input SWS data, and turns ON the wind-
shield wiper drive signal. When the wiper comes to 
the stop position, the windshield wiper auto-stop sig-
nal is turned OFF, and the windshield wiper drive sig-
nal turns OFF.

When the intermittent time TI is elapsed after being 
turned ON the windshield wiper drive signal, the 
windshield wiper drive signal is turned ON again, and 
the above-mentioned operation is repeated.

Mist wiper control

When the windshield wiper mist switch of the column 
switch is turned ON while the ignition switch is ACC 
or ON, the column switch turns ON the windshield 
wiper drive signal. At the same time, the wiper speed 
switching relay turns to ON (HI). When the wind-
shield mist wiper switch is ON, the windshield wipers 
operate at the high speed.

AC304772

OFF

AC304772

OFF

AB

TI: Intermittent time

ON

Windshield wiper 
auto stop signal

TI

TI

TI

ON

Windshield wiper 
drive signal

AC300283

OFF

AD

TI: Intermittent time

ON

Windshield wiper 
auto stop signal

TI

TI

(LO) OFF

(HI) ON

Windshield wiper intermittent operation

Windshield wiper switch 
"OFF" position

Windshield wiper 
speed switching relay

Windshield wiper 
drive signal

OFF

ON

Windshield wiper 
"MIST" switch

OFF

ON

GENERAL INFORMATION

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-6

Low speed wiper and high speed wiper control

When the windshield low speed wiper switch of the 
column switch is turned ON while the ignition switch 
is ACC or ON, the column switch turns ON the wind-
shield wiper drive signal. Also, the wiper speed 
switching relay turns to OFF (LO), and the windshield 
wipers operate at the low speed.

When the windshield high speed wiper switch is 
turned ON, the windshield wiper drive signal turns 
ON. Also, the wiper speed switching relay turns ON 
(HI), and the windshield wipers operate at the high 
speed.

Windshield wiper linked with washer function (initial condition: function available)

AC300284

OFF

AC

ON

Windshield wiper 
auto stop signal

(LO) OFF

(HI) ON

Windshield wiper high speed operation

Windshield wiper speed 
switching relay

Windshield wiper 
drive signal

OFF

ON

Windshield wiper "LO" switch

OFF

ON

Windshield wiper low speed operation

Windshield wiper "HI" switch

OFF

ON

AC207005AD

t

t

ON

OFF

ON

OFF

ON

OFF

ON

OFF

T

T

T1

T1

Windshield wiper relay

Windshield wiper 
auto stop signal

Windshield washer relay

Windshield washer switch

Wiper switch in 
off position

Wiper switch in intermittent  
operation position

t: 0.3 seconds
T: 3 seconds
T1: Intermittent wiper 
     intermittent time

Wiper 
switch

OFF position

Intermittent operation position

Low-speed or 
high-speed 
operation 
position

Washer 
switch ON 
time

0.3 
seconds 
or less

0.3 to 
0.5 
seconds

0.5 to 
0.7 
seconds

0.7 
seconds 
or more

0.2 
seconds 
or less

0.2 to 
0.5 
seconds

0.5 to 
0.7 
seconds

0.7 
seconds 
or more

-

T1


second


second


seconds


seconds


second


second


seconds


seconds

3 seconds

 

 

 

 

 

 

 

Content   ..  108  109  110  111   ..