Lexus RX450h (2022 year). Manual in english - page 24

 

  Index      Manuals     Lexus RX450h (2022 year). Manual in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

 

 

Content      ..     22      23      24      25     ..

 

 

 

Lexus RX450h (2022 year). Manual in english - page 24

 

 

399

6-3. Do-it-yourself maintenance

6

Mai
nte

na

nc

e a

nd

 c

are

10

Install the cover.

11

Remove the protective tape.

Back-up lights (bulb type)

1

Open the back door and remove 
the cover.

Using a flathead screwdriver, remove the 

cover.
To prevent scratching to the vehicle, wrap 

the tip of the flathead screwdriver with a 

cloth, etc.

2

Turn the bulb base counterclock-
wise and remove it.

3

Remove the light bulb.

4

Install a new light bulb and then 
install the bulb base to the light unit 
by inserting it and turning it clock-
wise.

After installing the bulb base, wiggle it 

lightly to make sure it is securely installed 

and turn on the back-up lights to visually 

check that there is no light leaking from 

between the bulb base and light unit.

5

Install the cover.

Align the tabs of the cover with the grooves 

and install the cover.

400

6-3. Do-it-yourself maintenance

WARNING

To prevent injury

Before performing any light bulb 

replacement procedure, be sure to turn 

the power switch off. Failure to do so may 

result in burns from hot components or a 

part of your body may get caught on an 

operating component, possibly causing 

serious injury.

Replacing light bulbs

Turn off the lights. Do not attempt to 

replace the bulb immediately after 

turning off the lights.

The bulbs become very hot and may 

cause burns.

Do not touch the glass portion of the 

light bulb with bare hands. When it is 

unavoidable to hold the glass portion, 

use and hold with a clean dry cloth to 

avoid getting moisture and oils on the 

bulb.

Also, if the bulb is scratched or 

dropped, it may blow out or crack.

Fully install light bulbs and any parts 

used to secure them. Failure to do so 

may result in heat damage, fire, or 

water entering the headlight unit. This 

may damage the headlights or cause 

condensation to build up on the lens.

Do not attempt to repair or disassem-

ble the light bulbs, connectors, electric 

circuits or component parts.

Doing so may result in death or serious 

injury due to electric shock.

To prevent damage or fire

Make sure bulbs are fully seated and 

locked.

Check the wattage of the bulb before 

installing to prevent heat damage.

401

7

7

When trouble

 ari

ses

When trouble arises

.

7-1. Essential information

Emergency flashers..................

402

If your vehicle has to be stopped in 

an emergency..........................

402

If the vehicle is submerged or 

water on the road is rising
........................................................

403

7-2. Steps to take in an emergency

If your vehicle needs to be towed

........................................................

405

If you think something is wrong

........................................................

409

If a warning light turns on or a 

warning buzzer sounds ........

410

If a warning message is displayed

........................................................

420

If you have a flat tire..................

424

If the hybrid system will not start

........................................................

436

If you lose your keys.................

438

If the fuel filler door cannot be 

opened........................................

438

If the electronic key does not 

operate properly ....................

439

If the 12-volt battery is discharged

.........................................................

441

If your vehicle overheats ........

446

If the vehicle becomes stuck

........................................................

449

402

7-1. Essential information

7-1.Essential information

Press the switch.

All the turn signal lights will flash. To turn 
them off, press the switch once again.

Emergency flashers

If the emergency flashers are used for a 

long time while the hybrid system is not 

operating (while the “READY” indicator 

is not illuminated), the 12-volt battery may 

discharge.

If any of the SRS airbags deploy (inflate) 

or in the event of a strong rear impact, the 

emergency flashers will turn on automati-

cally. 

The emergency flashers will turn off auto-

matically after operating for approxi-

mately 20 minutes. To manually turn the 

emergency flashers off, press the switch 

twice. 

(The emergency flashers may not turn on 

automatically depending on the force of 

the impact and conditions of the colli-

sion.)

1

Steadily step on the brake pedal 
with both feet and firmly depress it.

Do not pump the brake pedal repeatedly 

as this will increase the effort required to 

slow the vehicle.

2

Shift the shift lever to N.

If the shift lever is shifted to N

3

After slowing down, stop the vehi-
cle in a safe place by the road.

4

Stop the hybrid system.

If the shift lever cannot be shifted to 
N

3

Keep depressing the brake pedal 
with both feet to reduce vehicle 
speed as much as possible.

4

To stop the hybrid system, press 
and hold the power switch for 2 
consecutive seconds or more, or 

Emergency flashers

The emergency flashers are used to 
warn other drivers when the vehicle 
has to be stopped on the road due 
to a breakdown, etc.

Operating instructions

If your vehicle has to be 
stopped in an emergency

Only in an emergency, such as if it 
becomes impossible to stop the 
vehicle in the normal way, stop the 
vehicle using the following proce-
dure:

Stopping the vehicle

403

7-1. Essential information

7

W

he

n t

ro

ub

le

 a

ris

es

press it briefly 3 times or more in 
succession.

5

Stop the vehicle in a safe place by 
the road.

If the door can be opened, open the 
door and exit the vehicle.

If the door cannot be opened, open 
the window using the power window 
switch and ensure an escape route.

If the window can be opened, exit 
the vehicle through the window.

If the door and window cannot be 
opened due to the rising water, 
remain calm, wait until the water 
level inside the vehicle rises to the 
point that the water pressure inside 
of the vehicle equals the water pres-
sure outside of the vehicle and then 
open the door after waiting for the 
rising water to enter the vehicle, and 
exit the vehicle. When the outside 
water level exceeds half the height 
of the door, the door cannot be 
opened from the inside due to water 
pressure.

Water level exceeds the floor

When the water level exceeds the floor and 

time has passed, the electrical equipment 

will get damaged, the power windows will 

WARNING

If the hybrid system has to be turned 

off while driving

Power assist for the steering wheel will 

be lost, making the steering wheel 

heavier to turn. Decelerate as much as 

possible before turning off the hybrid sys-

tem.

If the vehicle is submerged 
or water on the road is rising

This vehicle is not designed to be 
able to drive on roads that are 
deeply flooded with water. Do not 
drive on roads where the roads may 
be submerged or the water may be 
rising. It is dangerous to remain in 
the vehicle, if it anticipated that the 
vehicle will be flooded or set a drift. 
Remain calm and follow the follow-
ing.

404

7-1. Essential information

not operate, the engine and motor stop, and 

the vehicle may not be able to get moving.

Using an emergency escape hammer

*1

Laminated glass

*2

 is used in the windshield 

and the windows on this vehicle. Laminated 

glass cannot be shattered with an emer-
gency hammer

*1

.

*1

: Contact your Lexus dealer or aftermar-

ket accessory manufacturer for further 
information about an emergency ham-
mer.

*2

: If equipped

How to distinguish laminated glass

When looking from the cross-sectional 

view point, laminated glass is two sheets of 

glass pasted together.

Laminated glass
Tempered glass

WARNING

Caution while driving

Do not drive on roads where the roads 

may be submerged or the water may be 

rising. Otherwise the vehicle may be 

damaged and cannot move, as well as 

become flooded and set a drift, which 

may lead to death.

A
B

405

7-2. Steps to take in an emergency

7

W

he

n t

ro

ub

le

 a

ris

es

7-2.Steps to take in an emergency

If your vehicle needs to be 
towed

If towing is necessary, we recom-
mend having your vehicle towed by 
your Lexus dealer or commercial 
towing service, using a wheel-lift 
type truck or flatbed truck.

Use a safety chain system for all 
towing, and abide by all state/pro-
vincial and local laws.

If towing your vehicle with a 
wheel-lift type truck, use a towing 
dolly. (

P.406, 405)

WARNING

Observe the following precautions.Fail-

ure to do so may result in death or seri-

ous injury.

When towing the vehicle

Be sure to transport the vehicle with all 

four wheels raised off the ground. If the 

vehicle is towed with the tires contacting 

the ground, the drivetrain or related 

parts may be damaged, the vehicle may 

fly off the truck, or electricity generated 

by the operation of the motor may cause 

a fire to occur depending on the nature 

of the damage or malfunction.

While towing

When towing using cables or chains, 

avoid sudden starts, etc. which place 

excessive stress on the towing eyelets, 

cables or chains. The towing eyelets, 

cables or chains may become dam-

aged, broken debris may hit people, 

and cause serious damage.

Do not turn the power switch off.

There is a possibility that the steering 

wheel is locked and cannot be oper-

ated.

Installing towing eyelets to the vehi-

cle

Make sure that towing eyelets are 

installed securely. If not securely 

installed, towing eyelets may come loose 

during towing.

406

7-2. Steps to take in an emergency

The following may indicate a problem 
with your transmission. Contact your 
Lexus dealer or commercial towing 

service before towing.

The hybrid system warning message 
is shown on the multi-information 
display and the vehicle does not 
move.

The vehicle makes an abnormal 
sound.

From the front

Use a towing dolly under the rear 
wheels.

From the rear

Use a towing dolly under the front 
wheels.

NOTICE

To prevent damage to the vehicle 

when towing using a wheel-lift type 

truck

Do not tow the vehicle from the rear 

when the power switch is off. The 

steering lock mechanism is not strong 

enough to hold the front wheels 

straight.

When raising the vehicle, ensure ade-

quate ground clearance for towing at 

the opposite end of the raised vehicle. 

Without adequate clearance, the vehi-

cle could be damaged while being 

towed.

To prevent damage to the vehicle 

when towing with a sling-type truck

Do not tow with a sling-type truck, either 

from the front or rear.

To prevent damage to the vehicle 

during emergency towing

Do not secure cables or chains to the 

suspension components.

Recreational towing (behind motor 

home, etc.)

Never dinghy tow your vehicle to pre-

vent causing serious damage to the 

Hybrid AWD system and transmission. 

(

P.181)

Situations when it is necessary to 
contact dealers before towing

Towing with a wheel-lift type 
truck

407

7-2. Steps to take in an emergency

7

W

he

n t

ro

ub

le

 a

ris

es

When using a flat-bed truck to trans-
port the vehicle, use tire strapping 
belts. Refer to the owner's manual of 
the flat-bed truck for the tire strapping 
method.
In order to suppress vehicle movement 
during transportation, set the parking 
brake and turn the power switch off.

If a tow truck is not available in an 
emergency, your vehicle may be tem-
porarily towed using cables or chains 
secured to the emergency towing eye-
lets. This should only be attempted on 
hard surfaced roads for short distances 
at under 18 mph (30 km/h).
A driver must be in the vehicle to steer 
and operate the brakes. The vehicle’s 
wheels, drive train, axles, steering and 
brakes must be in good condition.

To have your vehicle towed by another 
vehicle, the towing eyelet must be 
installed to your vehicle. Install the tow-
ing eyelet using the following proce-
dure.

1

Take out the towing eyelet. 
(

P.425)

2

Remove the eyelet cover.

Except F SPORT models

F SPORT models

NOTICE

Towing with a sling-type truck

Do not tow with a sling-type truck to pre-

vent body damage.

Using a flatbed truck

Emergency towing (vehicles 
with towing eyelets)

Emergency towing procedure 
(vehicles with towing eyelets)

408

7-2. Steps to take in an emergency

3

Insert the towing eyelet into the 
hole and tighten partially by hand.

4

Tighten down the towing eyelet 
securely using a wheel nut wrench 
or hard metal bar.

5

Securely attach cables or chains to 
the towing eyelet.

Take care not to damage the vehicle body.

6

Enter the vehicle being towed and 
start the hybrid system.

If the hybrid system does not start, turn the 

power switch to ON mode.

7

Shift the shift lever to N and release 
the parking brake.

Turn automatic mode off. (

P.194)

When the shift lever cannot be shifted: 

P.190

While towing

If the hybrid system is off, the power assist 

for the brakes and steering will not function, 

making steering and braking more difficult.

Wheel nut wrench

Wheel nut wrench is installed in luggage 

compartment. (

P.425)

409

7-2. Steps to take in an emergency

7

When trouble

 ari

ses

Fluid leaks under the vehicle
(Water dripping from the air condi-
tioning after use is normal.)

Flat-looking tires or uneven tire 
wear

Engine coolant temperature gauge 
needle continually points higher 
than normal

Changes in exhaust sound

Excessive tire squeal when corner-
ing

Strange noises related to the sus-
pension system

Pinging or other noises related to 
the hybrid system

Engine missing, stumbling or run-
ning roughly

Appreciable loss of power

Vehicle pulls heavily to one side 
when braking

Vehicle pulls heavily to one side 
when driving on a level road

Loss of brake effectiveness, spongy 
feeling, pedal almost touches the 
floor

If you think something is 
wrong

If you notice any of the following 
symptoms, your vehicle probably 
needs adjustment or repair. Con-
tact your Lexus dealer as soon as 
possible.

Visible symptoms

Audible symptoms

Operational symptoms

410

7-2. Steps to take in an emergency

Brake system warning light

Brake system warning light

High coolant temperature warning light

*

 (warning buzzer)

*

: This light illuminates on the multi-information display.

If a warning light turns on or a warning buzzer sounds

Calmly perform the following actions if any of the warning lights comes on or 
flashes. If a light comes on or flashes, but then goes off, this does not necessar-
ily indicate a malfunction in the system. However, if this continues to occur, 
have the vehicle inspected by your Lexus dealer.

Actions to the warning lights or warning buzzers

Warning light

Details/Actions

(U.S.A.)

or

(red)

(Canada)

Indicates that:

The brake fluid level is low; or

The brake system is malfunctioning

Immediately stop the vehicle in a safe place and contact your Lexus 
dealer. Continuing to drive the vehicle may be dangerous.

Warning light

Details/Actions

(yellow)

Indicates a malfunction in:

The regenerative braking system;

The electronically controlled brake system; or

The electric parking brake

Have the vehicle inspected by your Lexus dealer immediately.

Warning light

Details/Actions

Indicates that the engine coolant temperature is too high

Immediately stop the vehicle in a safe place.
Handling method (

P.446)

411

7-2. Steps to take in an emergency

7

When trouble

 ari

ses

Hybrid system overheat warning light

*

(warning buzzer)

*

: This light illuminates on the multi-information display.

Charging system warning light

*

*

: Except F SPORT models: This light illuminates on the multi-information display.

F SPORT models: This light illuminates on the meter.

Low engine oil pressure warning light

*

 (warning buzzer)

*

: This light illuminates on the multi-information display.

Malfunction indicator lamp

Warning light

Details/Actions

Indicates the hybrid system has overheated

Stop the vehicle in a safe place.
Handling method (

P.448)

Warning light

Details/Actions

Indicates a malfunction in the vehicle’s charging system

Immediately stop the vehicle in a safe place and contact your Lexus 
dealer. Continuing to drive the vehicle may be dangerous.

Warning light

Details/Actions

Indicates that the engine oil pressure is too low

Immediately stop the vehicle in a safe place and contact your Lexus 
dealer.

Warning light

Details/Actions

(U.S.A.)

or

(Canada)

Indicates a malfunction in:

The hybrid system;

The electronic engine control system; or

The electronic throttle control system;

Have the vehicle inspected by your Lexus dealer immediately.

412

7-2. Steps to take in an emergency

SRS warning light

ABS warning light

Brake Override System warning light/Drive-Start Control warning light

*

 

(warning buzzer)

*

: This light illuminates on the multi-information display.

Warning light

Details/Actions

Indicates a malfunction in:

The SRS airbag system;

The front passenger occupant classification system; or

The seat belt pretensioner system

Have the vehicle inspected by your Lexus dealer immediately.

Warning light

Details/Actions

(U.S.A.)

or

(Canada)

Indicates a malfunction in:

The ABS; or

The brake assist system

Have the vehicle inspected by your Lexus dealer immediately.

Warning light

Details/Actions

When a buzzer sounds:

Brake Override System is malfunctioning;

Drive-Start Control is operating;

Drive-Start Control is malfunctioning; or

PKSB (Parking Support Brake) (if equipped) is operating

Follow the instructions displayed on the multi-information display.

When a buzzer does not sound:
Brake Override System is operating

Release the accelerator pedal and depress the brake pedal.

413

7-2. Steps to take in an emergency

7

When trouble

 ari

ses

Electric power steering system warning light (warning buzzer)

Low fuel level warning light

Driver’s and front passenger’s seat belt reminder light (warning buzzer)

*

*

: Driver’s seat belt warning buzzer:

The driver’s seat belt warning buzzer sounds to alert the driver that his or her seat belt is not 
fastened. Once the power switch is turned to ON mode, the buzzer sounds. If the seat belt 
is still unfastened, the buzzer sounds intermittently for a certain period of time after the 
vehicle reaches a certain speed.
Front passenger’s seat belt warning buzzer:
The front passenger’s seat belt warning buzzer sounds to alert the front passenger that his 
or her seat belt is not fastened. If the seat belt is unfastened, the buzzer sounds intermit-
tently for a certain period of time after the vehicle reaches a certain speed.

Warning light

Details/Actions

(red)

or

(yellow)

Indicates a malfunction in the EPS (Electric Power Steering) system

Have the vehicle inspected by your Lexus dealer immediately.

Warning light

Details/Actions

Indicates that remaining fuel is approximately 2.9 gal. (11.0 L, 2.4 Imp. 
gal.) or less

Refuel the vehicle.

Warning light

Details/Actions

Warns the driver and/or front passenger to fasten their seat belts

Fasten the seat belt. 
If the front passenger’s seat is occupied, the front passenger’s seat 
belt also needs to be fastened to make the warning light (warning 
buzzer) turn off.

414

7-2. Steps to take in an emergency

Rear passengers’ seat belt reminder light

*1

 (warning buzzer)

*2

*1

: This light illuminates on the center panel.

Regardless of whether or not a rear passenger is present, if the power switch is turned to 
ON mode with the rear seat belts unfastened, this light will also illuminate for a certain 
period of time.

*2

: Rear passengers’ seat belt warning buzzer:

The rear passengers’ seat belt warning buzzer sounds to alert the rear passenger that his or 
her seat belt is not fastened. If the seat belt is unfastened, the buzzer sounds intermittently 
for a certain period of time, after the seat belt is fastened and unfastened and the vehicle 
reaches a certain speed.

Tire pressure warning light

LTA indicator (warning buzzer)

Warning light

Details/Actions

(RX450h)

or

(RX450hL)

Warns the rear passengers to fasten their seat belts

Fasten the seat belt.

Warning light

Details/Actions

Indicates the following:

Low tire pressure due to flat tire;

Low tire pressure due to natural causes; or

The tire pressure warning system is malfunctioning

Immediately stop the vehicle in a safe place.
Handling method (

P.417)

Warning light

Details/Actions

(orange)

Indicates a malfunction in the LTA (Lane Tracing Assist)

Follow the instructions displayed on the multi-information display. 
(

P.233)

 

 

 

 

 

 

 

Content      ..     22      23      24      25     ..