|
|
|
34-1
CRUISE CONTROL
HOT IN ON OR START
ENGINE
CONTROL
MODULE
(ECM)
Solid State:
Do not check
resistance.
DASH
FUSE
BOX
11
I-9
Connector
1
CRUISE
SET
INDICATOR
LIGHT
See
Indicators
I-9
Connector
METER
ASSEMBLY
CB-11
METER
15A
YEL
WHT
Indicator
control
42
WHT
H-4
Connector
1
2
GRN
GRN
39
CLUTCH
SWITCH
Open with
clutch pedal
depressed.
5
H-17
Connector
GRN
WHT/
GRN
E-22
Connector
76
E-21
Connector
Drive
input
21
H-4
Connector
13
H-17
Connector
WHT
YEL
I-14
Connector
I-14
Connector
See Dash Fuse
Box, page 11-2.
See Dash Fuse
Box, page 11-3.
M/T
Circuit Schematic
34-2
CRUISE CONTROL
Automatic
Transmission
Controls
Page 39-7
Anti-lock
Brake System
(ABS)
Page 44-1
Intelligent
Suspension
Control
System
Page 38
HOT AT ALL TIMES
CB-6
STOP
LIGHT
15A
3
GRY/RED
BLU
1
GRN
39
RED
BRAKE
SWITCH
DASH
FUSE
BOX
Brake Lights
Page 110-7
(Rodeo)
Page 110-8
(Rodeo Sport)
Shift Interlock
System
Page 138
12
RED
RED
4
1
2
3
GRN
M
CB-14
BACK-UP/
TURN
LIGHT
15A
29
H-4
Connector
32
H-17
Connector
16
GRY/RED
See Dash
Fuse Box,
page 11-2.
See Ground
Distribution,
page 14-8.
E-30
Brake
switch
input
2
GRN
69
5
RED
38
6
BLU
76
8
RED/
WHT
3
7
BLU/
WHT
65
E-21
Connector
E-22
Con-
nector
See Ground
Distribution,
page 14-7.
E-28
4
GRN/WHT
THROTTLE
VALVE
ASSEMBLY
Throttle
Position
Sensor 1
Throttle
Valve
Motor
Throttle
Position
Sensor 2
BLK
BLK
WHT/GRN
WHT/GRN
GRY/RED
RED
BLK
Throttle
valve motor
(+)
TPS 1
input
TPS 2
input
Reference
Reference
E-21
Connector
Brake
input
Throttle
valve
motor
(–)
Sensor
ground
Sensor
ground
BLK
BLK
46
48
41
61
HOT IN ON OR START
I-18
Connector
I-18
Connector
E-5
Con-
nector
E-5
Connector
RED
H-16
Connector
Circuit Schematic
34-3
CRUISE CONTROL
78
E-21
Con-
nector
41
ORN
77
BLU/
GRN
79
E-22
Connector
7
ORN/BLU
ACCELERATION
POSITION
SENSOR
ASSEMBLY
APS 3
input
Reference
E-22
Connector
Sensor
ground
Acceleration
Position
Sensor 3
H-7
Connector
14
From B on
this page.
H-7
Connector
6
7
ORN
BLU/
GRN
BLK
Acceleration
Position
Sensor 2
BLK
80
8
GRN
2
YEL
3
BLU
APS 2
input
Reference
E-21
Connector
Sensor
ground
12
BLU
From A on
this page.
4
5
BLK
Acceleration
Position
Sensor 1
To A on
this page.
BLK
63
10
BLK
36
5
WHT
68
E-22
Connector
4
RED
APS 1
input
Reference
Sensor
ground
See Ground
Distribution,
page 14-7.
E-28
10
RED
BLK
BLK
BLK
2
3
BLK
11
BLK
BLK
GRN
YEL
BLK
WHT
ENGINE
CONTROL
MODULE
(ECM)
Solid State:
Do not check
resistance.
ENGINE
CONTROL
MODULE
(ECM)
Solid State:
Do not check
resistance.
BLK
BLK
BLK
A
A
C-48
Connector
C-48
Connector
1
6
To B on
this page.
9
ORN/BLU
BLK
Circuit Schematic
34-4
CRUISE CONTROL
(Refer to Section 201 for photographs.)
Component
Photo No.
Acceleration Position
Sensor Assembly
Part of the acceleration pedal
129
. . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Switch
Behind left side of I/P, on brake pedal support
68
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Switch
Behind left side of I/P, on clutch pedal support
65
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dash Fuse Box
Left side of I/P, behind panel
58
. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Control Module
(ECM)
Left side of engine compartment
44
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Throttle Valve Assembly
Top front of engine, on intake manifold
46
. . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connector
H-4 (52-GRY)
Left side of engine compartment
27
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
H-7 (16-BLK)
Left side of engine compartment
27
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
H-17 (19-BLK)
Behind left kick panel
62
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I-9 (14-GRN)
Behind left side of I/P, on top of meter assembly
86
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
I-32 (20-WHT)
Behind left side of I/P
66
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground
E-28
Left side of intake manifold
54
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-30
Right side of intake manifold
21
. . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Circuit Operation
With the starter switch in ON, the engine (M/T) or pow-
ertrain (A/T) control module is powered. This system
uses mechanical, and electrical operated devices to
maintain vehicle speed at a setting selected and con-
trolled by the driver. See owner’s manual for further
instruction.
System Operation
The cruise control system will set and automatically
maintain any speed above 25 mph (40 km/h). To set,
press the cruise control main switch so that the
“CRUISE ON/OFF” indicator is on. After reaching the
desired speed, press the set switch. The engine (M/T)
or powertrain (A/T) control module will receive a set sig-
nal input and will activate the throttle valve motor.
Pushing the cruise control main switch cancels the
cruise control system. This signals the engine (M/T) or
powertrain (A/T) control module and erases the set
speed from memory. The cruise control system also
disengages when cruising speed is lower than the pre-
set speed by 12.5 mph (20 km/h) or more. If the system
is disengaged temporarily by the brake switch, clutch
switch, or the automatic transmission mode switch and
vehicle speed is still above 25 mph (40 km/h), turn and
release the resume/accel switch. With the resume/ac-
cel switch turned and released, the set memory is re-
tained. The vehicle automatically returns to the pre-
viously set speed.
For gradual acceleration without depressing the accel-
erator pedal, turn the resume/accel switch and hold it
there until the desired speed is reached. This will send
an acceleration signal to the engine (M/T) or powertrain
(A/T) control module. When the switch is released, the
system will be reprogrammed for the new speed.
Quickly turning and releasing the resume/accel switch
allows you to tap up the preset cruising speed.
Each turn increases the preset speed by 1 mph (1.6
km/h). The preset speed can be increased by up to 10
mph (16 km/h) in this manner. To slow the vehicle down,
depress and hold the set/coast switch. This will send a
deceleration signal to the engine (M/T) or powertrain
(A/T) control module, causing the vehicle to coast until
the desired speed is reached. When the desired speed
is reached, release the set/coast switch. This will repro-
gram the system for the new speed. Quickly depressing
and releasing the set/coast switch allows you to tap
down the preset cruising speed. Each depress de-
creases the preset speed by 1 mph (1.6 km/h). The pre-
set speed can be decreased to a minimum of 25 mph
(40 km/h) in this manner.
Component Location Index
|
|
|