Infiniti QX56 (Z62). Manual - part 23

DOOR MIRROR REMOTE CONTROL SWITCH

ADP-85

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Refer to 

ADP-85, "MIRROR SWITCH : Diagnosis Procedure"

.

MIRROR SWITCH : Diagnosis Procedure

INFOID:0000000006248382

1.

CHECK MIRROR SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Turn ignition switch ON.

4.

Check voltage between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK MIRROR SWITCH CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect automatic drive positioner control unit connector.

3.

Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.

4.

Check continuity between automatic drive positioner control unit harness connector and ground.

Is the inspection result normal?

YES

>> Replace automatic drive positioner control unit.

NO

>> Repair or replace harness.

3.

CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT

MIR CON SW-RH/LH

When operating the mirror switch toward the right or left side.

: ON

Other than the above.

: OFF

Monitor item

Condition

(+)

(-)

Voltage (V)

(Approx.)

Door mirror remote control switch 

Connector

Terminal

M8

4

Ground

5

5

6

14

Automatic drive positioner control unit 

Door mirror remote control switch 

Continuity 

Connector

Terminal

Connector

Terminal

M75

3

M8

6

Existed

4

5

15

14

16

4

Automatic drive positioner control unit 

Ground

Continuity 

Connector

Terminal

M75

3

Not existed

4

15

16

ADP-86

< DTC/CIRCUIT DIAGNOSIS >

DOOR MIRROR REMOTE CONTROL SWITCH

1.

Turn ignition switch OFF.

2.

Check continuity between door mirror remote control switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK MIRROR SWITCH

Check door mirror remote control switch (mirror switch).
Refer to 

ADP-86, "MIRROR SWITCH : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace door mirror remote control switch (mirror switch).

5.

CHECK INTERMITTENT INCIDENT

Check intermittent incident.
Refer to 

GI-40, "Intermittent Incident"

.

>> INSPECTION END

MIRROR SWITCH : Component Inspection

INFOID:0000000006248383

1.

CHECK MIRROR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect door mirror remote control switch connector.

3.

Check continuity between door mirror remote control switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace door mirror remote control switch.

Door mirror remote control switch

Ground

Continuity

 Connector

Terminal

M8

13

Existed

Door mirror remote control switch

Condition

Continuity

Terminal

4

13

Mirror switch

RIGHT

Existed

Other than the above

Not existed

5

LEFT

Existed

Other than the above

Not existed

6

UP

Existed

Other than the above

Not existed

14

DOWN

Existed

Other than the above

Not existed

POWER SEAT SWITCH GROUND CIRCUIT

ADP-87

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

K

L

M

A

B

ADP

N

O

P

POWER SEAT SWITCH GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000006248384

1.

CHECK POWER SEAT SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect power seat switch connector.

3.

Check continuity between power seat switch harness connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Repair or replace harness or connector.

Power seat switch

Ground

Continuity 

Connector

Terminal

B459

43

Existed

ADP-88

< DTC/CIRCUIT DIAGNOSIS >

TILT &TELESCOPIC SWITCH GROUND CIRCUIT

TILT &TELESCOPIC SWITCH GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000006248385

1.

CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect tilt & telescopic switch connector.

3.

Check continuity between tilt & telescopic switch harness connector and ground.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-40, "Intermittent Incident"

.

NO

>> Repair or replace harness.

Tilt & telescopic switch

Ground

Continuity

Connector

Terminal

M102

1

Existed