Infiniti G35 (V35). Manual - part 48

TROUBLE DIAGNOSIS FOR SYMPTOMS

AT-183

D

E

F

G

H

I

J

K

L

M

A

B

AT

In “N” Position, Vehicle Moves

NCS000I1

SYMPTOM:

Vehicle moves forward or backward when selecting “N” position.

DIAGNOSTIC PROCEDURE

1. 

CHECK PNP SWITCH CIRCUIT

Perform self-diagnosis. Refer to 

AT-86, "SELF-DIAGNOSTIC RESULT MODE"

 , 

AT-95, "Diagnostic Procedure

Without CONSULT-II"

 .

Do the self-diagnostic results indicate PNP switch?

YES

>> Check the malfunctioning system. Refer to 

AT-106, "DTC P0705 PARK/NEUTRAL POSITION

SWITCH"

 .

NO

>> GO TO 2.

2. 

CHECK A/T POSITION

Check A/T position. Refer to 

AT-216, "Checking of A/T Position"

 .

OK or NG

OK

>> GO TO 3.

NG

>> Adjust A/T position. Refer to 

AT-215, "Adjustment of A/T Position"

 .

3. 

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

AT-12, "Checking A/T Fluid"

 .

OK or NG

OK

>> GO TO 4.

NG

>> Refill ATF.

4. 

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

AT-225, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

 .

2.

Check A/T fluid condition. Refer to 

AT-50, "A/T Fluid Condition Check"

 .

OK or NG

OK

>> GO TO 5.

NG

>> Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to

AT-60, "Symptom Chart"

  (Symptom No.67).

5. 

CHECK SYMPTOM

Check again. Refer to 

AT-54, "Check at Idle"

 .

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 6.

6. 

CHECK TCM 

1.

Check TCM input/output signals. Refer to 

AT-83, "TCM Input/Output Signal Reference Values"

 .

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

AT-184

TROUBLE DIAGNOSIS FOR SYMPTOMS

Large Shock (“N” to “D” Position)

NCS000I2

SYMPTOM:

A noticeable shock occurs when the selector lever is shifted from the “N” to “D” position.

DIAGNOSTIC PROCEDURE

1. 

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

AT-86, "SELF-DIAGNOSTIC RESULT MODE"

 , 

AT-95, "Diagnostic Procedure

Without CONSULT-II"

 .

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

AT-86, "SELF-DIAGNOSTIC RESULT MODE"

 , 

AT-97,

"Judgment Self-diagnosis Code"

 .

NO

>> GO TO 2.

2. 

CHECK ENGINE IDLE SPEED

Check the engine idle speed. Refer to 

EC-76, "Idle Speed and Ignition Timing Check"

 .

OK or NG

OK

>> GO TO 3.

NG

>> Adjust engine idle speed. Refer to 

EC-76, "Idle Speed and Ignition Timing Check"

 .

3. 

CHECK A/T POSITION

Check A/T position. Refer to 

AT-216, "Checking of A/T Position"

 .

OK or NG

OK

>> GO TO 4.

NG

>> Adjust A/T position. Refer to 

AT-215, "Adjustment of A/T Position"

 .

4. 

CHECK A/T FLUID LEVEL

Check the A/T fluid level. Refer to 

AT-12, "Checking A/T Fluid"

 .

OK or NG

OK

>> GO TO 5.

NG

>> Refill ATF.

5. 

CHECK LINE PRESSURE

Check line pressure at idle with selector lever in “D” position. Refer to 

AT-52, "LINE PRESSURE TEST"

 .

OK or NG

OK

>> GO TO 8.

NG - 1 >> Line pressure high: GO TO 6.
NG - 2 >> Line pressure low: GO TO 7.

6. 

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

AT-225, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

 .

2.

Disassemble A/T. Refer to 

AT-263, "DISASSEMBLY"

 .

3.

Check the following.

–

Oil pump assembly. Refer to 

AT-279, "Oil Pump"

 .

OK or NG

OK

>> GO TO 8.

NG

>> Repair or replace damaged parts.

TROUBLE DIAGNOSIS FOR SYMPTOMS

AT-185

D

E

F

G

H

I

J

K

L

M

A

B

AT

7. 

DETECT MALFUNCTIONING ITEM

1.

Check control valve with TCM. Refer to 

AT-225, "Control Valve with TCM and A/T Fluid Temperature Sen-

sor 2"

 .

2.

Disassemble A/T. Refer to 

AT-263, "DISASSEMBLY"

 .

3.

Check the following.

–

Oil pump assembly. Refer to 

AT-279, "Oil Pump"

 .

–

Power train system. Refer to 

AT-263, "DISASSEMBLY"

 .

–

Transmission case. Refer to 

AT-263, "DISASSEMBLY"

 .

OK or NG

OK

>> GO TO 8.

NG

>> Repair or replace damaged parts.

8. 

CHECK A/T FLUID CONDITION

1.

Remove oil pan. Refer to 

AT-225, "Control Valve with TCM and A/T Fluid Temperature Sensor 2"

 .

2.

Check A/T fluid condition. Refer to 

AT-50, "A/T Fluid Condition Check"

 .

OK or NG

OK

>> GO TO 10.

NG

>> GO TO 9.

9. 

DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to 

AT-60,

"Symptom Chart"

  (Symptom No.1).

OK or NG

OK

>> GO TO 10.

NG

>> Repair or replace damaged parts.

10. 

CHECK SYMPTOM

Check again. Refer to 

AT-54, "Check at Idle"

 .

OK or NG

OK

>> INSPECTION END

NG

>> GO TO 11.

11. 

CHECK TCM 

1.

Check TCM input/output signals. Refer to 

AT-83, "TCM Input/Output Signal Reference Values"

 .

2.

If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.

OK or NG

OK

>> INSPECTION END

NG

>> Repair or replace damaged parts.

AT-186

TROUBLE DIAGNOSIS FOR SYMPTOMS

Vehicle Does Not Creep Backward in “R” Position

NCS000I3

SYMPTOM:

The vehicle does not creep in the “R” position. Or an extreme lack of acceleration is observed.

DIAGNOSTIC PROCEDURE

1. 

CHECK SELF-DIAGNOSTIC RESULTS

Perform self-diagnosis. Refer to 

AT-86, "SELF-DIAGNOSTIC RESULT MODE"

 , 

AT-95, "Diagnostic Procedure

Without CONSULT-II"

 .

Is any malfunction detected by self-diagnostic results?

YES

>> Check the malfunctioning system. Refer to 

AT-86, "SELF-DIAGNOSTIC RESULT MODE"

 , 

AT-97,

"Judgment Self-diagnosis Code"

 .

NO

>> GO TO 2.

2. 

CHECK A/T POSITION

Check A/T position. Refer to 

AT-216, "Checking of A/T Position"

 .

OK or NG

OK

>> GO TO 3.

NG

>> Adjust A/T position. Refer to 

AT-215, "Adjustment of A/T Position"

 .

3. 

CHECK A/T FLUID LEVEL

Check A/T fluid level. Refer to 

AT-12, "Checking A/T Fluid"

 .

OK or NG

OK

>> GO TO 4.

NG

>> Refill ATF.

4. 

CHECK STALL TEST

Check stall revolution with selector lever in “M” and “R” positions. Refer to 

AT-50, "STALL TEST"

 .

OK or NG

OK

>> GO TO 6.

OK in “M” position, NG in “R” position>>GO TO 5.
NG in both “M” and “R” positions>>GO TO 8.

5. 

DETECT MALFUNCTIONING ITEM

1.

Disassemble A/T. Refer to 

AT-263, "DISASSEMBLY"

 .

2.

Check the following.

–

Reverse brake. Refer to 

AT-263, "DISASSEMBLY"

 .

OK or NG

OK

>> GO TO 9.

NG

>> Repair or replace damaged parts.

6. 

CHECK LINE PRESSURE

Check the line pressure with the engine idling. Refer to 

AT-52, "LINE PRESSURE TEST"

 .

OK or NG

OK

>> GO TO 9.

NG - 1 >> Line pressure high. GO TO 7.
NG - 2 >> Line pressure low. GO TO 8.