Hummer H3. Manual - part 1194

 

  Index      Hummer     Hummer H3 - service repair manual 2006-2009 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1192  1193  1194  1195   ..

 

 

Hummer H3. Manual - part 1194

 

 

To setup the digital radio receiver, complete the setup procedure under the Special Functions 
menu of the scan tool, then cycle ignition. 

XM Activation 

1. Turn the radio ON, tune to the XM channel 0 and record the radio ID. The radio ID will be 

needed for activation of the receiver.  

2. From the USA, Call XM radio at 1-800-556-3600 to activate the receiver. From Canada, 

call 1-877-438-9677.  

3. Park the vehicle outside in an area with an unobstructed view of the southern sky.  

4. Leave the vehicle outside with the ignition switch in the ACC position and the radio on for 

30 minutes to activate XM service.  

5. Once activated, the radio will receive the remaining XM channels.  

ONSTAR GLOBAL POSITIONING SYSTEM (GPS) DATA NOT CURRENT OR INACCURATE 

Diagnostic Aids 



The Global Positioning System (GPS) Signal title on the scan tool will display a Yes or No 
dependent upon whether or not the module sees an increment of the seconds transmitted by 
GPS signals to the vehicle communication interface module. Upon entering this screen, the 
GPS Signal title will automatically display Yes, regardless of the presence of time 
increment, for at least 2 seconds, while the algorithm in the scan tool determines the status 
of the clock. If increment is found, Yes is continually displayed. If the clock remains static, 
No is displayed. The scan tool looks for increment every second, regardless of current 
display.  



Inaccurate or aged GPS position concerns which are no longer present may have been due 
to the temporary loss of GPS signal reception by the vehicle. Conditions such as driving 
through tunnels or parking structures while making an OnStar® keypress will restrict the 
navigation antenna from a clear view of the satellites in the sky and may have caused this 
temporary data loss.  

systems: 



DTCs  



GMLAN and class 2 radio messages  

IMPORTANT: After replacement of an XM receiver, call XM radio to deactivate 

the receiver that has been removed from the vehicle.

 

2007 Hummer H3 

2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3

  

OnStar Global Positioning System (GPS) Data Not Current or Inaccurate 

Step

Action

Values

Yes

No

Schematic Reference: Radio/Navigation System Schematics 
Connector End View Reference: Entertainment/Communication Connector End 
Views

1

Did you perform the Diagnostic 
System Check - Vehicle?

-

Go to Step 2 

Go to 
Diagnostic 
System 
Check - 
Vehicle
 

2

With a scan tool, observe the GPS 
signal status indicator in the GPS Data 
Display menu, for at least 10 
seconds.Does the indicator display 
Yes?

IMPORTANT:

It is important to have the vehicle in an 
open outside area where a cellular call 
can be successfully placed and Global 
Positioning System (GPS) data can be 
received from satellites. It is also 
necessary to inform the OnStar® Call 
Center advisor that this call is for vehicle 
diagnostic purposes.

-

Go to Step 3  Go to Step 6 

3

1. Press the OnStar® Call Center 

button.  

2. Ask the OnStar® Call Center 

advisor if they have received 
GPS data.  

Has the advisor received GPS data?

-

Go to Step 4  Go to Step 5 

4

Ask the OnStar® Call Center advisor 
to verify your position. 
Is the location provided by the 
OnStar® Call Center advisor within a 
reasonable distance from the actual 
location of the vehicle?

-

Go to 
Diagnostic 
Aids

Go to Step 

10 

Ask the OnStar® Call Center advisor 
if this call was a fail to voice. 

Contact the 
General 

 

2007 Hummer H3 

2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3

  

5

Was the call a fail to voice?

-

Motors 
Technical 
Assistance 
Center

Go to Step 6 

6

1. Disconnect the navigation 

antenna coax from the navigation 
antenna within the wiring 
harness.  

2. Disconnect the navigation 

antenna from the vehicle 
communication interface module 
(VCIM).  

3. Measure the resistance from the 

center conductor of the coax to 
the metal outer shield.  

Does the meter read out of limits?

IMPORTANT:

Vehicle may be equipped with sectioned 
coax. Test each section and replace only 
the faulty section, not the entire length 
or coax.

-

Go to Step 7  Go to Step 8 

7

Measure the resistance of the 
navigation antenna coax center 
conductor from end to end. 
Does the resistance measure greater 
than the specified value?

1 ohms

Go to Step 8  Go to Step 9 

8

Replace the navigation antenna coax. 
Did you complete the replacement?

-

Go to Step 

11 

-

9

Replace the navigation antenna 
assembly. Refer to Global 
Positioning System (GPS) Antenna 
Replacement

Did you complete the replacement?

-

Go to Step 

11 

-

10

Replace the VCIM. Refer to Control 
Module References
 for replacement, 
setup and programming. 
Did you complete the replacement?

-

Go to Step 

11 

-

 

2007 Hummer H3 

2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3

  

ONSTAR MICROPHONE INOPERATIVE - CALLER CANNOT BE HEARD 

OnStar Microphone Inoperative - Caller Cannot Be Heard 

11

Operate the system in order to verify 
the repair. 
Did you correct the condition?

-

Go to Step 2 

-

Step

Action

Value(s)

Yes

No

Schematic Reference: OnStar Schematics 
Connector End View Reference: Entertainment/Communication Connector End 
Views
 
DEFINITION: The OnStar® Call Center operator can clearly be heard but the operator is 
unable to hear the caller.

1

Did you perform the Diagnostic 
System Check - Vehicle?

-

Go to Step 2 

Go to 
Diagnostic 
System 
Check - 
Vehicle
 

2

1. Turn ON the ignition, with the 

engine OFF.  

2. Press the OnStar® Call Center 

button.  

3. Ask the OnStar® operator if 

your voice can clearly be 
heard.  

Does the OnStar® operator hear 
your voice?

-

Go to Testing 
for 
Intermittent 
Conditions 
and Poor 
Connections
 

Go to Step 3 

3

1. Turn OFF the ignition.  

2. Disconnect the cellular 

microphone connector.  

3. Turn ON the ignition, with the 

engine OFF.  

4. Measure the voltage from the 

cellular microphone signal 
circuit to a good ground.  

Does the voltage measure greater 

9 V

 

2007 Hummer H3 

2007 ACCESSORIES AND EQUIPMENT Cellular, Entertainment and Navigation - H3

  

 

 

 

 

 

 

 

Content   ..  1192  1193  1194  1195   ..