Hummer H2. Manual - part 570

 

  Index      Hummer     Hummer H2 - service repair manual 2004 year

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  568  569  570  571   ..

 

 

Hummer H2. Manual - part 570

 

 

The motor control circuit monitored by the driver seat module is determined to be shorted to ground, battery 
positive voltage, or open. 

Action Taken When the DTC Sets 

z

The seat motor with a current status DTC will be disabled.  

z

When the fault is no longer present a history status DTC will be stored, and motor operation will be 
restored.  

Conditions for Clearing the DTC 

z

The DTC will be current for as long as the fault is present.  

z

When the fault is no longer present the DTC will be a history status code.  

z

The history DTC will be cleared after 100 error free ignition cycles, or by using the scan tool clearing 
DTCs feature.  

Diagnostic Aids 

When an adjuster motor control circuit is shorted to ground the driver seat module will also set a DTC B3962. 

DTC B1770, B1775, B1780, B1785, B1790, B1805, or B2415 

Step

Action

Yes

No

Schematic Reference:Driver Seat Schematics 
Connector End View Reference:Power Seat Systems Connector End Views

1

Did you perform the Power Seat Diagnostic 
System Check?

Go to Step 2

Go to Diagnostic 

System Check - 

Power Seat 

Systems

2

Verify the fault is present. 
Does the system operate normally?

Go to Testing for 

Intermittent Conditions 

and Poor Connections in 

Wiring Systems

Go to Step 3

3

1. Disconnect the appropriate seat adjuster 

motor connector.  

2. Connect a test lamp across the adjuster 

motor control circuit terminals in the harness 
connector.  

3. Operate the appropriate seat adjuster switch 

in both directions.  

Does the test lamp illuminate when the switch is 
activated in both directions?

Go to Step 5

Go to Step 4

4

Test the motor control circuits for an open or short 
to ground. Refer to Circuit Testing and to Wiring 
Repairs in Wiring Systems. 

 

2004 Hummer H2 

2004 ACCESSORIES & EQUIPMENT Seats - Hummer H2

  

DTC B1825 

Circuit Description 

The seat recline motor is equipped with a potentiometer type position sensor used by the driver seat module to 
determine the position of the seat back. The motor position sensor is supplied with 5-volt reference and ground 
circuits from the driver seat module. The position sensor signal circuit is referenced from ground within the 
driver seat module. The signal voltage monitored by the driver seat module ranges from 0.39-4.58 volts and is 
determined by the wiper location on the resistor within the motor position sensor. The position sensor circuit 
voltage level is used by the driver seat module to determine the position of the seat back when storing or 
recalling memory position settings. 

Conditions for Running the DTC 

The system voltage must be between 9.0-16.0 volts. 

Conditions for Setting the DTC 

The recline motor position sensor signal circuit voltage level to the driver seat module is not within the 0.39-
4.58 volt range. 

Did you find and correct the condition?

Go to Step 9

Go to Step 6

5

Inspect for poor connections at the adjuster motor 
connector. Refer to Testing for Intermittent 
Conditions and Poor Connections and to 
Connector Repairs in Wiring Systems. 
Did you find and correct the condition?

Go to Step 9

Go to Step 7

6

Inspect for poor connections at the harness 
connector of the driver seat module. Refer to 
Testing for Intermittent Conditions and Poor 
Connections and to Connector Repairs in Wiring 
Systems. 
Did you find and correct the condition?

Go to Step 9

Go to Step 8

7

Replace the appropriate adjuster motor assembly. 
Refer to Seat Adjuster Motor Replacement - 
Front . 
Did you complete the replacement?

Go to Step 9

-

8

Replace the driver seat module. Refer to Memory 
Seat Control Module Replacement . 
Did you complete the replacement?

Go to Step 9

-

9

1. Use the scan tool in order to clear the DTCs. 

2. Operate the vehicle within the Conditions for 

Running the DTC.  

Does the DTC reset?

Go to Step 3

System OK

 

2004 Hummer H2 

2004 ACCESSORIES & EQUIPMENT Seats - Hummer H2

  

Action Taken When the DTC Sets 

The recline motor will not function during memory or exit position recall operation. 

Conditions for Clearing the DTC 

z

The DTC will be current for as long as the fault is present.  

z

When the fault is no longer present the DTC will be a history status code.  

z

The history DTC will be cleared after 100 error free ignition cycles, or by using the scan tool clearing 
DTCs feature.  

Diagnostic Aids 

A short to voltage on a sensor signal circuit or an open ground may effect other sensors using common 5-volt 
reference and ground circuits causing the following DTCs to set: 

z

B2435  

z

B2440  

z

B3606  

Test Description 

The numbers below refer to the step numbers on the diagnostic table. 

3: Tests for the proper operation of the signal circuit in the low voltage range.  

4: Tests for the proper operation of the signal circuit in the high voltage range.  

5: Tests for a short to voltage in the 5-volt reference circuit.  

DTC B1825 

Step

Action

Values

Yes

No

Schematic Reference:Driver Seat Schematics 
Connector End View Reference:Power Seat Systems Connector End Views

1

Did you perform the Power Seat Systems 
Diagnostic System Check?

-

Go to Step 2

Go to Diagnostic 

System Check - 

Power Seat 

Systems

2

1. Install a scan tool.  

2. With a scan tool, observe the Recline 

Position Sensor parameter in the driver 
seat module Sensor Data list.  

Is the Recline Position Sensor parameter 
within the specified range?

0.39-

4.58 V

Go to Testing for 

Intermittent 

Conditions and Poor 

Connections in Wiring 

Systems

Go to Step 3

1. Disconnect the recline motor position 

 

2004 Hummer H2 

2004 ACCESSORIES & EQUIPMENT Seats - Hummer H2

  

3

sensor.  

2. With a scan tool, observe the Recline 

Position Sensor parameter.  

Is the Recline Position Sensor parameter less 
than the specified value?

0.39 V

Go to Step 4

Go to Step 8

4

1. Connect a 3-ampere fused jumper wire 

between the signal circuit of the recline 
position sensor and the 5-volt reference 
circuit of the recline position sensor.  

2. With a scan tool, observe the Recline 

Position Sensor parameter.  

Is the Recline Position Sensor parameter 
greater than the specified value?

4.58 V

Go to Step 5

Go to Step 7

5

1. Disconnect the fused jumper wire.  

2. Measure the voltage between the 5-volt 

reference circuit of the recline position 
sensor and the signal circuit of the 
recline position sensor.  

Is the recline position sensor parameter 
greater than the specified value?

5 V

Go to Step 6

Go to Step 10

6

Test the 5-volt reference circuit of the recline 
position sensor for a short to voltage. Refer to 
Circuit Testing and to Wiring Repairs in 
Wiring Systems. 
Did you find and correct the condition?

-

Go to Step 15

Go to Step 12

7

Test the 5-volt reference circuit of the recline 
position sensor for one of the following 
conditions: 

z

A short to ground  

z

A high resistance  

z

An open  

 
Refer to Circuit Testing and to Wiring 
Repairs in Wiring Systems. 
Did you find and correct the condition?

-

Go to Step 15

Go to Step 9

8

Test the signal circuit of the recline position 
sensor for a short to voltage. Refer to Circuit 
Testing and to Wiring Repairs in Wiring 
Systems. 

-

 

2004 Hummer H2 

2004 ACCESSORIES & EQUIPMENT Seats - Hummer H2

  

 

 

 

 

 

 

 

Content   ..  568  569  570  571   ..