Hummer H2. Manual - part 2437

 

  Index      Hummer     Hummer H2 - service repair manual 2004 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  2435  2436  2437  2438   ..

 

 

Hummer H2. Manual - part 2437

 

 

5

1. Turn OFF the ignition.  

2. Disconnect the AT inline 20-way connector, 

additional DTCs may set.  

3. Install the J 44152 Jumper Harness (20 pins) on 

the engine side of the AT inline 20-way 
connector.  

4. Turn ON the ignition, with the engine OFF.  

5. Using the J 35616 GM Terminal Test Kit, 

connect a test lamp from terminal E of the 
44152
 to ground. 

Refer to Automatic Transmission Inline 20-
Way Connector End View
 . 

Does the test lamp illuminate?

-

Go to Step 6

Go to Step 15

6

1. Connect a test lamp between terminal E and 

terminal S of the J 44152 . 

Refer to Automatic Transmission Inline 20-
Way Connector End View
 . 

2. Use the scan tool in order to command the 3-2 

SS valve assembly ON and OFF three times.  

Does the test lamp turn ON and OFF with each 
command?

-

Go to Step 8

Go to Step 7

7

Is the test lamp always ON?

-

Go to Step 16

Go to Step 17

8

1. Install the J 44152 on the transmission side of 

the AT inline 20-way connector.  

2. Using the DMM and the J 35616 , measure the 

resistance between the terminal E and terminal 
S of the J 44152 . 

Refer to Automatic Transmission Inline 20-
Way Connector End View
 . 

Does the resistance measure within the specified 
range?

20-32 

ohm

Go to Step 9

Go to Step 10

9

1. Measure the resistance from terminal S to 

ground.  

2. Measure the resistance from terminal E to 

ground.  

250 K 

ohm

Go to 

Intermittent 

Conditions in 

 

2004 Hummer H2 

2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2

 

Do both readings measure greater than the specified 
value?

Engine Controls - 

6.0L (LQ4)

Go to Step 11

10

1. Disconnect the AT wiring harness assembly 

from the 3-2 SS valve assembly.  

2. Measure the resistance of the 3-2 SS valve 

assembly.  

Does the resistance measure within the specified 
range?

20-32 

ohm

Go to Step 18

Go to Step 19

11

1. Disconnect the AT wiring harness assembly 

from the 3-2 SS valve assembly.  

2. Measure the resistance from the component's 

terminals to ground.  

Do both readings measure greater than the specified 
value?

250 K 

ohm

Go to Step 18

Go to Step 19

12 Test the Ignition 0 voltage circuit of the 3-2 SS valve 

assembly for a short to ground between the fuse block 
and the AT inline 20-way connector.Refer to Testing 
for Short to Ground
 and extxref 
document="029_body-21" filetype="sgml" 
extrefid="i162420">Wiring Repairs in Wiring 
Systems.Did you find and correct the condition?

IMPORTANT:

The condition that affects this circuit may exist in 
other connecting branches of the circuit. Refer to 
Power Distribution Schematics in Wiring Systems 
for complete circuit distribution.

-

Go to Step 21

Go to Step 13

13

Test the Ignition 1 voltage circuit of the 3-2 SS valve 
assembly for a short to ground between the AT inline 
20-way connector and the 3-2 SS valve 
assembly.Refer to Testing for Short to Ground in 
Wiring Systems.Did you find a short to ground 
condition?

IMPORTANT:

The condition that affects this circuit may exist in 
other connecting branches of the circuit. Refer to 
Power Distribution Schematics in Wiring Systems 
for complete circuit distribution.

-

Go to Step 18

Go to Step 14

14

1. Test each solenoid for a short to ground.  

2. Replace the faulty solenoid as necessary.  

-

-

 

2004 Hummer H2 

2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2

 

Did you complete the replacement?

Go to Step 21

15

Test the Ignition 0 voltage circuit of the 3-2 SS valve 
assembly for an open.Refer to Testing for 
Continuity
 and extxref document="029_body-21" 
filetype="sgml" extrefid="i162420">Wiring Repairs 
in Wiring Systems.Did you find and correct the 
condition?

IMPORTANT:

The condition that affects this circuit may exist in 
other connecting branches of the circuit. Refer to 
Power Distribution Schematics in Wiring Systems 
for complete circuit distribution.

-

Go to Step 21

-

16

Test the control circuit of the 3-2 SS valve assembly 
for a short to ground between the PCM connector C1 
and the AT inline 20-way connector. 
Refer to Testing for Short to Ground and extxref 
document="029_body-21" filetype="sgml" 
extrefid="i162420">Wiring Repairs in Wiring 
Systems. 
Did you find and correct the condition?

-

Go to Step 21

Go to Step 20

17

Test the control circuit of the 3-2 SS valve assembly 
for an open or short to voltage between the PCM 
connector C1 and the AT inline 20-way connector. 
Refer to Circuit Testing and extxref 
document="029_body-21" filetype="sgml" 
extrefid="i162420"> Wiring Repairs in Wiring 
Systems. 
Did you find and correct the condition?

-

Go to Step 21

Go to Step 20

18

Replace the AT wiring harness assembly. 
Refer to Valve Body and Pressure Switch 
Replacement
 . 
Did you complete the replacement?

-

Go to Step 21

-

19

Replace the 3-2 SS valve assembly. 
Refer to Valve Body and Pressure Switch 
Replacement
 . 
Did you complete the replacement?

-

Go to Step 21

-

20

Replace the PCM. 
Refer to Powertrain Control Module (PCM) 
Replacement
 in Engine Controls - 6.0L (LQ4). 
Did you complete the replacement?

-

Go to Step 21

-

Perform the following procedure in order to verify the 
repair: 

1. Select DTC.  

2. Select Clear Info.  

 

2004 Hummer H2 

2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2

 

DTC P0894 

21

3. Drive the vehicle in D3 or D4 and perform a 3-

2 downshift. Ensure that the following 
conditions are met: 

z

The PCM commands the 3-2 SS valve 
assembly ON, and the voltage feedback 
drops to zero.  

z

The PCM commands the 3-2 SS valve 
assembly OFF, and the voltage feedback 
increases to B+.  

z

All conditions are met for 5 seconds.  

4. Select Specific DTC.  

5. Enter DTC P0785.  

 
Has the test run and passed?

-

Go to Step 22

Go to Step 2

22

With the scan tool, observe the stored information, 
capture info, and DTC Info. 
Does the scan tool display any DTCs that you have 
not diagnosed?

-

Go to Diagnostic 

Trouble Code 

(DTC) List in 

Engine Controls - 

6.0L (LQ4)

System OK

 

2004 Hummer H2 

2004 TRANSMISSION Automatic Transmission - 4L60-E/4L65-E Diagnosis (DTC P0218 To DTC P2771) - Hummer H2

 

 

 

 

 

 

 

 

Content   ..  2435  2436  2437  2438   ..