Hummer H2. Manual - part 1633

DTC P0132 OR P0152

Circuit Description

Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the
oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach
operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the
time required for the sensors to reach operating temperature. The powertrain control module (PCM) supplies the
HO2S with a reference, or bias, voltage of about 450 mV. When the engine is first started the PCM operates in
open loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperature and closed loop is
achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias
voltage. High HO2S voltage indicates a rich exhaust stream; low HO2S voltage indicates a lean exhaust stream.
If the PCM detects an HO2S voltage that stays above a specified value, DTC P0132 sets for HO2S bank 1
sensor 1, or DTC P0152 sets for HO2S bank 2 sensor 1.

Conditions for Running the DTC

Rich Test Enable:

DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120,
P0200, P0220, P0300, P0442, P0446, P0452, P0453, P0455, P0496, P1125, P1258, P1516, P2101,
P2108, P2135, U0107 are not set.

The Loop Status parameter is closed.

Replace the affected HO2S. Refer to Heated Oxygen
Sensor (HO2S) Replacement Bank 1 Sensor 1 or
Heated Oxygen Sensor (HO2S) Replacement Bank
2 Sensor 1 .
Did you complete the replacement?

Go to Step 15

Replace the PCM. Refer to Powertrain Control
Module (PCM) Replacement .
Did you complete the replacement?

Go to Step 15

1. Clear the DTCs with a scan tool.

2. Turn OFF the ignition for 30 seconds.

3. Start the engine.

4. Operate the vehicle within the Conditions for

Running the DTC. You may also operate the
vehicle within the conditions that you observed
from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 2

Go to Step 16

Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?

Go to

Diagnostic

Trouble Code

(DTC) List

System OK

2004 Hummer H2

2004 ENGINE PERFORMANCE Engine Controls Diagnosis (DTC P0068 To DTC P0141/P0161) - 4.8L, 5.3L, and 6.0L -

Hummer H2

The Ignition 1 Signal parameter is between 10-18 volts.

The Fuel Tank Level Remaining parameter is more than 10 percent.

The TP Indicated Angle parameter is between 3-70 percent more than the value observed at idle.

Decel. Fuel Cutoff Test Enable:

The Loop Status parameter is closed.

The Ignition 1 Signal parameter is between 10-18 volts.

The Fuel Tank Level Remaining parameter is more than 10 percent.

The Engine Run Time parameter is more than 30 seconds.

The Decel. Fuel Cutoff parameter is active for more than 2 seconds.

Conditions for Setting the DTC

Rich Test:

The PCM detects that the affected HO2S voltage parameter is more than 900 mV for 165 seconds.

Decel. Fuel Cutoff Test:

The PCM detects that the affected HO2S voltage parameter is more than 540 mV for 5 seconds.

Action Taken When the DTC Sets

The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition
cycle that the diagnostic runs and fails.

The control module records the operating conditions at the time the diagnostic fails. The first time the
diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic
reports a failure on the second consecutive ignition cycle, the control module records the operating
conditions at the time of the failure. The control module writes the operating conditions to the Freeze
Frame and updates the Failure Records.

The control module commands the Loop Status open.

Conditions for Clearing the MIL/DTC

The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles
that the diagnostic runs and does not fail.

2004 Hummer H2

2004 ENGINE PERFORMANCE Engine Controls Diagnosis (DTC P0068 To DTC P0141/P0161) - 4.8L, 5.3L, and 6.0L -

Hummer H2

A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other
emission related diagnostic.

Clear the MIL and the DTC with a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

2: If the voltage is varying above and below the specified range, the condition is not present.

DTC P0132 or P0152

Step

Action

Value

(s)

Yes

Schematic Reference:Engine Controls Schematics
Connector End View Reference:Engine Controls Connector End Views or Powertrain Control
Module (PCM) Connector End Views

Did you perform the Diagnostic System Check-Engine
Controls?

Go to Step 2

Go to Diagnostic

System Check -

Engine Controls

1. Start the engine.

2. Allow the engine to reach operating temperature.

Refer to Scan Tool Data List .

3. Observe the affected HO2S voltage parameter

with a scan tool.

Is the HO2S voltage parameter varying above and
below the specified range?

300-

600
mV

Go to Step 3

Go to Step 4

1. Observe the Freeze Frame/Failure Records for

this DTC.

2. Turn OFF the ignition for 30 seconds.

3. Start the engine.

4. Operate the vehicle within the Conditions for

Running the DTC. You may also operate the
vehicle within the conditions that you observed
from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 4

Go to

Intermittent

Conditions

1. Turn OFF the ignition.

2. Disconnect the affected heated oxygen sensor

(HO2S).

3. Turn ON the ignition, with the engine OFF.

400-

500

2004 Hummer H2

2004 ENGINE PERFORMANCE Engine Controls Diagnosis (DTC P0068 To DTC P0141/P0161) - 4.8L, 5.3L, and 6.0L -

Hummer H2

4. Observe the HO2S voltage parameter with a

scan tool.

Is the HO2S voltage parameter within the specified
range?

Go to Step 5

Go to Step 6

1. Connect a 3-amp fused jumper wire between the

high signal circuit of the HO2S harness
connector on the engine harness side and a good
ground.

2. Observe the HO2S voltage parameter with a

scan tool.

Is the HO2S voltage parameter less than the specified
value?

100
mV

Go to Step 7

Go to Step 8

Test the HO2S high signal circuit for a short to the
HO2S heater low control circuit. Refer to Circuit
Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

Go to Step 17

Go to Step 10

1. Remove the jumper wire from the previous step.

2. Connect a 3-amp fused jumper wire between the

high signal circuit of the HO2S harness
connector on the engine harness side and the low
signal circuit of the HO2S harness connector on
the engine harness side.

3. Observe the HO2S voltage parameter with a

scan tool.

Is the HO2S voltage parameter less than the specified
value?

100
mV

Go to Step 9

Go to Step 11

Test the HO2S high signal circuit for an open or high
resistance. Refer to Circuit Testing and Wiring
Repairs in Wiring Systems.
Did you find and correct the condition?

Go to Step 17

Go to Step 14

Test the HO2S low signal circuit for a short to the
HO2S heater low control circuit. Refer to Circuit
Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?

Go to Step 17

Go to Step 12

Test the HO2S high signal circuit for a short to
voltage. Refer to Circuit Testing and Wiring Repairs
in Wiring Systems.Did you find and correct the

IMPORTANT:

The sensor may be damaged if the circuit is shorted
to a voltage source.

2004 Hummer H2

2004 ENGINE PERFORMANCE Engine Controls Diagnosis (DTC P0068 To DTC P0141/P0161) - 4.8L, 5.3L, and 6.0L -

Hummer H2

Content .. 1631 1632 1633 1634 ..