Honda Accord Hybrid (2022 year). Manual in english - page 34

543

uu

Maintenance Under the Hood

u

Oil Check

Main

tenan

ce

Oil Check

We recommend that you check the engine oil level every time you refuel.
Park the vehicle on level ground.
Turn off the power system. You can check the oil level without the engine having 
run beforehand. If the engine has been running, wait approximately three minutes 
before you check the oil.

1.

Remove the dipstick (orange).

2.

Wipe the dipstick with a clean cloth or 
paper towel.

3.

Insert the dipstick back all the way into its 
hole.

4.

Remove the dipstick again, and check the 
level. It should be between the upper and 
lower marks. Add oil if necessary.

1

Oil Check

If the oil level is near or below the lower mark, slowly 
add oil, being careful not to overfill.

Upper Mark
Lower Mark

544

uu

Maintenance Under the Hood

u

Adding Engine Oil

Main

tenan

ce

Adding Engine Oil

1.

Unscrew and remove the engine oil fill cap.

2.

Add oil slowly.

3.

Reinstall the engine oil fill cap, and tighten 
it securely.

4.

Wait for three minutes and recheck the 
engine oil dipstick.

1

Adding Engine Oil

NOTICE

Do not fill the engine oil above the upper mark. 
Overfilling the engine oil may result in leaks and 
engine damage.

If any oil spills, wipe it away immediately. Spilled oil 
may damage the engine compartment components.

Engine Oil Fill Cap

545

uu

Maintenance Under the Hood

u

Changing the Engine Oil and Oil Filter

Continued

Main

tenan

ce

Changing the Engine Oil and Oil Filter

You must change the engine oil and oil filter regularly in order to maintain the 
engine’s lubrication. The engine may be damaged if they are not changed regularly.

Turning the power system on automatically starts the engine if the High Voltage 
battery charge level gauge shows two segments or less.

2

High Voltage Battery Charge Level Gauge

 P. 142

Change the oil and filter in accordance with the maintenance message on the driver 
information interface.

1.

Run the engine until it reaches normal 
operating temperature, and then turn the 
engine off.

2.

Open the hood and remove the engine oil 
fill cap.

3.

Remove the Phillips-head screws and 
slotted head screws by turning 90° 
counter-clockwise on the undercarriage 
and remove the under cover.

4.

Remove the drain bolt and washer from 
the bottom of the engine, and drain the 
oil into a suitable container.

1

Changing the Engine Oil and Oil Filter

NOTICE

You may damage the environment if you do not 
dispose of the oil in a suitable way. If you are 
changing the oil by yourself, appropriately dispose of 
the used oil. Put the oil in a sealed container and take 
it to a recycling center. Do not throw the oil away 
into a garbage can or onto the ground.

Drain Bolt

Washer

uu

Maintenance Under the Hood

u

Changing the Engine Oil and Oil Filter

546

Main

tenan

ce

5.

Remove the oil filter and dispose of the 
remaining oil.

6.

Check that the filter gasket is not stuck to 
the engine contact surface.

u

If it is stuck, you must detach it.

7.

Wipe away dirt and dust adhering to the 
contact surface of the engine block, and 
install a new oil filter.

u

Apply a light coat of new engine oil to 
the filter gasket.

8.

Put a new washer on the drain bolt, then 
reinstall the drain bolt.

u

Tightening torque:
30 lbf∙ft (40 N∙m, 4.0 kgf∙m)

9.

Pour the recommended engine oil into the 
engine.

u

Engine oil change capacity (including 
filter):
4.0 US qt (3.8 L)

10.

Reinstall the engine oil fill cap securely and 
start the engine.

11.

Run the engine for a few minutes, and 
then check that there is no leak from the 
drain bolt or oil filter.

12.

Stop the engine, wait for three minutes, 
and then check the oil level on the 
dipstick.

u

If necessary, add more engine oil.

1

Changing the Engine Oil and Oil Filter

You will need a special wrench to replace the oil 
filter. You can buy this wrench from a dealer.

When installing the new oil filter, follow the 
instructions supplied with the oil filter.

Reinstall the engine oil fill cap. Start the engine. If the 
low oil pressure warning appears, turn off the 
engine, and check your work.

Oil Filter

547

uu

Maintenance Under the Hood

u

Cooling System

Continued

Main

tenan

ce

Cooling System

This coolant is premixed with 50% antifreeze and 50% water. Do not add any 
straight antifreeze or water.

We recommend you check the engine coolant level every time you refuel. Check the 
reserve tank first. If it is completely empty, also check the coolant level in the 
radiator. Add the engine coolant accordingly.

1. Make sure the engine and radiator are 

cool.

2.

Check the amount of coolant in the reserve 
tank.

u

If the coolant level is below the 

MIN

 

mark, add the specified coolant until it 
reaches the 

MAX

 mark.

3.

Inspect the cooling system for leaks.

Specified coolant: Honda Long Life Antifreeze/Coolant Type 2

■

Reserve Tank

1

Cooling System

NOTICE

Genuine Honda engine coolant is a 50/50 mixture of 
antifreeze and water that can withstand freezing at 
temperatures as low as about -31°F (-35°C). If your 
vehicle is consistently subjected to temperatures 
below this, the concentration of antifreeze in the 
coolant should be increased. Consult a dealer for 
details.

If Honda antifreeze/coolant is not available, you may 
use another major brand of non-silicate coolant as a 
temporary replacement. Check that it is a high quality 
coolant recommended for aluminum engines. 
Continued use of any non-Honda coolant can result 
in corrosion, causing the cooling system to 
malfunction or fail. Have the cooling system flushed 
and refilled with Honda antifreeze/coolant as soon as 
possible.

Do not add rust inhibitors or other additives to your 
vehicle’s cooling system. They may not be compatible 
with the coolant or with the engine components.

3

WARNING

Removing the radiator cap while the 
engine is hot can cause the coolant to spray 
out, seriously scalding you.

Always let the engine and radiator cool 
down before removing the radiator cap.

Reserve 

Tank

MAX

MIN

uu

Maintenance Under the Hood

u

Cooling System

548

Main

tenan

ce

1. Make sure the engine and radiator are 

cool.

2.

Turn the radiator cap 1/8 turn counter-
clockwise and relieve any pressure in the 
cooling system.

3.

Push down and turn the radiator cap 
counter-clockwise to remove it.

4.

The coolant level should be up to the base 
of the filler neck. Add coolant if it is low.

5.

Put the radiator cap back on, and tighten it 
fully.

■

Radiator

1

Radiator

NOTICE

Pour the fluid slowly and carefully so you do not spill 
any. Clean up any spills immediately; they can 
damage components in the engine compartment.

Radiator Cap

549

uu

Maintenance Under the Hood

u

Inverter Coolant

Main

tenan

ce

Inverter Coolant

This coolant is premixed with 50% antifreeze and 50% water. Do not add any 
straight antifreeze or water.

We recommend you check the inverter coolant level every time you refuel.

Have a dealer replace the inverter coolant.

1.

Check the fluid level in the tank.

2.

If the coolant level has dropped below the 

MIN

 level, have your vehicle serviced at a 

dealer.

u

Only a properly trained technician can 
refill the coolant and check the system 
for leaks.

Specified coolant: Honda Long Life Antifreeze/Coolant Type 2

■

Checking the Coolant

1

Inverter Coolant

NOTICE

Genuine Honda engine coolant is a 50/50 mixture of 
antifreeze and water that can withstand freezing at 
temperatures as low as about -31°F (-35°C). If your 
vehicle is consistently subjected to temperatures 
below this, the concentration of antifreeze in the 
coolant should be increased. Consult a dealer for 
details.

If Honda antifreeze/coolant is not available, you may 
use another major brand non-silicate coolant as a 
temporary replacement. Check that it is a high quality 
coolant recommended for aluminum engines. 
Continued use of any non-Honda coolant can result 
in corrosion, causing the cooling system to 
malfunction or fail. Have the cooling system flushed 
and refilled with Honda antifreeze/coolant as soon as 
possible.

Do not add rust inhibitors or other additives to your 
vehicle’s coolant system. They may not be compatible 
with the coolant or with the motor components.

MAX

MIN

Filler 

Tank

550

uu

Maintenance Under the Hood

u

Transmission Fluid

Main

tenan

ce

Transmission Fluid

Have a dealer check the fluid level and replace if necessary.

Do not attempt to check or change the transmission fluid yourself.

Specified fluid: Honda ATF DW-1 (automatic transmission fluid)

1

Transmission Fluid

NOTICE

Do not mix Honda ATF DW-1 with other 
transmission fluids.

Using a transmission fluid other than Honda ATF 
DW-1 may adversely affect the operation and 
durability of your vehicle’s transmission, and damage 
the transmission.
Any damage caused by using a transmission fluid that 
is not equivalent to Honda ATF DW-1 is not covered 
by Honda’s new vehicle limited warranty.

551

uu

Maintenance Under the Hood

u

Brake Fluid

Main

tenan

ce

Brake Fluid

The fluid level should be between the 

MIN

 

and 

MAX

 marks on the side of the reserve 

tank.

Specified fluid: Honda Heavy Duty Brake Fluid DOT 3

■

Checking the Brake Fluid

1

Brake Fluid

NOTICE

Brake fluid marked DOT 5 is not compatible with your 
vehicle's braking system and can cause extensive 
damage.

If the specified brake fluid is not available, you should 
use only DOT 3 or DOT 4 fluid from a sealed 
container as a temporary replacement.

Using any non-Honda brake fluid can cause corrosion 
and decrease the longevity of the system. Have the 
brake system flushed and refilled with Honda Heavy 
Duty Brake Fluid DOT 3 as soon as possible.

If the brake fluid level is at or below the 

MIN

 mark, 

have a dealer inspect the vehicle for leaks or worn 
brake pads as soon as possible.

Reserve Tank

MIN

MAX

552

uu

Maintenance Under the Hood

u

Refilling Window Washer Fluid

Main

tenan

ce

Refilling Window Washer Fluid

Check the amount of window washer fluid by looking at the reservoir.

If the level is low, fill the washer reservoir.

If the washer fluid is low, a message appears 
on the driver information interface.

Pour the washer fluid carefully. Do not overflow the reservoir.

1

Refilling Window Washer Fluid

NOTICE

Do not use engine antifreeze or a vinegar/water 
solution in the windshield washer reservoir.
Antifreeze can damage your vehicle’s paint. A 
vinegar/water solution can damage the windshield 
washer pump.
Use only commercially available windshield washer 
fluid.
Avoid prolonged use of hard water to prevent lime 
scale buildup.

Canadian models

553

Continued

Main

tenan

ce

Replacing Light Bulbs

Headlight Bulbs

When replacing, use the following bulbs.

High beam headlight: LED type

*

High beam headlight: 60 W (HB3 for halogen bulb type)

*

Low beam headlight: LED type

1

Headlight Bulbs

NOTICE

Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the glass can cause 
the bulb to overheat and shatter.

The headlight aim is set by the factory, and does not 
need to be adjusted. However, if you regularly carry 
heavy items in the trunk, have the aiming readjusted 
at a dealer or by a qualified technician.

When replacing a halogen bulb, handle it by its base, 
and protect the glass from contact with your skin or 
hard objects. If you touch the glass, clean it with 
denatured alcohol and a clean cloth.

Models with halogen high beam headlights

All models

Models with halogen high beam headlights

* Not available on all models

uu

Replacing Light Bulbs

u

Headlight Bulbs

554

Main

tenan

ce

1.

Remove the hose and the holding clip using 
a flat-tip screwdriver, then remove the 
upper part of the window washer reservoir.

u

Check the amount of window washer 
fluid is below the upper part of the 
window washer reservoir and remove it.

2.

Push the tab to remove the coupler.

3.

Rotate the old bulb counter-clockwise to 
remove.

4.

Insert a new bulb into the headlight 
assembly and turn it clockwise.

5.

Insert the coupler into the connector of the 
bulb.

Low beam headlights are LED type. Have an authorized Honda dealer inspect and 
replace the light assembly.

■

High Beam Headlights

1

High Beam Headlights

High beam headlights are LED type. Have an 
authorized Honda dealer inspect and replace the light 
assembly.

When removing the clip, insert a flat-tip screwdriver, 
then lift and remove the clip.

Insert the clip with the pin raised, and push until it is 
flat.

Models with LED high beam headlights

Push until the pin 

is flat.

Models with halogen high beam headlights

Holding 

clip

Hose

Passenger side

Tab

Coupler

Bulb

Both sides

■

Low Beam Headlights

555

uu

Replacing Light Bulbs

u

Fog Lights

*

Main

tenan

ce

Fog Lights

*

Fog lights are LED type. Have an authorized Honda dealer inspect and replace the 
light assembly.

Parking/Daytime Running Lights

Parking/daytime running lights are LED type. Have an authorized Honda dealer 
inspect and replace the light assembly.

Front Turn Signal Lights

Front turn signal lights are LED type. Have an authorized Honda dealer inspect and 
replace the light assembly.

Front Side Marker Lights

Front side marker lights are LED type. Have an authorized Honda dealer inspect and 
replace the light assembly.

Side Turn Signal/Emergency Indicator Lights

*

Door mirror side turn lights are LED type. Have an authorized Honda dealer inspect 
and replace the light assembly.

* Not available on all models

556

uu

Replacing Light Bulbs

u

Brake Lights, Taillights, Rear Side Marker Lights, and Rear Turn Signal Light Bulbs

Main

tenan

ce

Brake Lights, Taillights, Rear Side Marker Lights, and 
Rear Turn Signal Light Bulbs

When replacing, use the following bulbs.

1.

Pry on the edge of the cover using a flat-tip 
screwdriver to remove the cover.

u

Wrap the flat-tip screwdriver with a cloth 
to prevent scratches.

2.

Remove the bolts.

3.

Pull the light assembly out of the rear pillar.

Brake Light: LED
Taillight: LED
Rear Side Marker Light: LED
Rear Turn Signal Light: 21 W (Amber)

1

Brake Lights, Taillights, Rear Side Marker Lights, and Rear Turn 
Signal Light Bulbs

Brake lights, taillights, and rear side marker lights are 
LED type. Have an authorized Honda dealer inspect 
and replace the light assembly.

Cover

Bolts

557

uu

Replacing Light Bulbs

u

Brake Lights, Taillights, Rear Side Marker Lights, and Rear Turn Signal Light Bulbs

Main

tenan

ce

4.

Turn the socket counter-clockwise and 
remove it.

5.

Push and turn the old bulb clockwise and 
remove it, and insert a new bulb.

Bulb

Socket

558

uu

Replacing Light Bulbs

u

Taillights, Brake Lights

*

, and Back-Up Light Bulbs

Main

tenan

ce

Taillights, Brake Lights

*

, and Back-Up Light Bulbs

When replacing, use the following bulbs.

1.

Remove the holding clips using a flat-tip 
screwdriver, then pull the lining back.

2.

Turn the socket counter-clockwise and 
remove it.

3.

Remove the old bulb and insert a new bulb.

Taillight: LED
Brake Light

*

: LED

Back-Up Light: 16 W

1

Taillights, Brake Lights

*

, and Back-Up Light Bulbs

Taillights and brake lights

*

 are LED type. Have an 

authorized Honda dealer inspect and replace the light 
assembly.

When removing the clip, insert a flat-tip screwdriver, 
then lift and remove the clip.

Insert the clip with the pin raised, and push until it is 
flat.

Clip

Push until the 

pin is flat.

Holding Clip

Bulb

Socket

Driver side

* Not available on all models