Content .. 9 10 11 12 ..

Honda Insight (2022 year). Manual in english - page 11

173

Opening and Closing the Trunk

Emergency Trunk Opener

Co
ntrols

Emergency Trunk Opener

The trunk release lever allows you to open the
trunk from inside for your safety.

Slide the release lever in the direction of the
arrow.

Emergency Trunk Opener

Parents should decide if their children should be
shown how to use this feature.

Lever

174

Co
ntrols

Security System

Immobilizer System

The immobilizer system prevents a key that has not been pre-registered from
starting the power system. Each key contains electronic transmitters that use
electronic signals to verify the key.

Pay attention to the following when pressing the

POWER

button:

•

Do not allow objects that emit strong radio waves near the

POWER

button.

•

Make sure the key is not covered by or touching a metal object.

•

Do not bring a key from another vehicle’s immobilizer system near the

POWER

button.

•

Do not put the key near magnetic items. Electronic devices, such as televisions
and audio systems emit strong magnetic fields. Note that even a key chain can
become magnetic.

Immobilizer System

NOTICE

Leaving the key in the vehicle can result in theft or
accidental movement of the vehicle.
Always take the key with you whenever you leave the
vehicle unattended.

Do not alter the system or add other devices to it.
Doing so may damage the system and make your
vehicle inoperable.

175

Security System

Security System Alarm

Continued

Co
ntrols

Security System Alarm

The security system alarm activates when the trunk, hood or doors are forcibly
opened. The alarm does not activate if the trunk or doors are opened with the key,
remote transmitter or keyless access system.
However, the alarm activates if a door is opened with the key and then the hood is
opened before the power mode is set to ON.

■

When the security system alarm activates

The horn sounds intermittently and some exterior lights flash.

■

To deactivate the security system alarm

Unlock the vehicle using the key, remote transmitter or keyless access system, or set
the power mode to ON. The system, along with the horn and flashing lights, is
deactivated.

■

Setting the security system alarm

The security system alarm automatically sets when the following conditions have
been met:

•

The power mode is set to VEHICLE OFF (LOCK).

•

The hood is closed.

•

All doors and the trunk are locked from outside with the key, remote transmitter
or keyless access system.

■

When the security system alarm sets

The security system alarm indicator in the instrument panel blinks and the blinking
interval changes after about 15 seconds.

■

To cancel the security system alarm

The security system alarm is canceled when the vehicle is unlocked using the remote
transmitter or keyless access system, or when the power mode is set to ON. The
security system alarm indicator goes off at the same time.

Security System Alarm

Do not alter the system or add other devices to it.
Doing so may damage the system and make your
vehicle inoperable.

The security system alarm continues for a maximum
of two minutes until the security system alarm
deactivates.

Do not set the security system alarm when someone
is in the vehicle or a window is open. The system can
accidentally activate when:

•

Unlocking the door with the lock tab.

•

Opening the trunk with the trunk opener or the
emergency trunk opener.

•

Opening the hood with the hood release.

If the 12-volt battery goes dead after you have set the
security system alarm, the security alarm may go off
once the 12-volt battery is recharged or replaced.
If this occurs, deactivate the security system alarm by
unlocking a door using the key, remote transmitter,
or keyless access system.

176

Security System

Security System Alarm

Co
ntrols

■

The panic button on the remote
transmitter

If you press the panic button for
approximately one second, the following will
occur for about 30 seconds:

•

The horn sounds.

•

Some exterior lights flash.

■

Canceling panic mode

•

Press any button on the remote transmitter.

•

Set the power mode to ON.

■

Panic Mode

Panic

Button

177

Continued

Co
ntrols

Opening and Closing the Windows

Opening/Closing the Power Windows

The power windows can be opened and closed when the power mode is in ON,
using the switches on the doors.

The driver’s side switches can be used to open and close all the windows. The power
window lock button on the driver’s side must be switched off (indicator off) to open
and close the windows from anywhere other than the driver’s seat.

When the power window lock button is pressed, the indicator comes on and you
can only operate the driver’s window. Turn the power window lock button on if a
child is in the vehicle.

■

Manual operation

To open:

Push the switch down lightly, and

hold it until the desired position is reached.

To close:

Pull the switch up lightly, and hold it

until the desired position is reached.

■

Automatic operation

To open:

Push the switch down firmly.

To close:

Pull the switch up firmly.

The window opens or closes completely. To
stop the window at any time, push or pull the
switch briefly.

■

Opening/Closing the Windows with Auto-Open/Close

Function

Opening/Closing the Power Windows

The power windows can be operated for up to 10
minutes after you set the power mode to VEHICLE
OFF (LOCK).
Opening either front door cancels this function.

Auto Reverse

If a power window senses resistance when closing
automatically, it will stop closing and reverse
direction.

The driver’s window auto reverse function is disabled
when you continuously pull up the switch.

The auto reverse function stops sensing when the
window is almost closed to ensure that it fully closes.

WARNING

Closing a power window on someone’s
hands or fingers can cause serious injury.

Make sure your passengers are away from
the windows before closing them.

Power

Window

Lock Button

Indicator

Driver’s Window

Switch

Front Passenger’s

Window Switch

Opening and Closing the Windows

Opening/Closing the Power Windows

178

Co
ntrols

To open:

Push the switch down.

To close:

Pull the switch up.

Release the switch when the window reaches
the desired position.

To open:

Press the unlock button, and then

within 10 seconds, press it again and hold it.

If the windows stop midway, repeat the
procedure.

■

Opening/Closing Windows without Auto-Open/Close Function

Opening/Closing the Power Windows

While driving with any of the windows open, you
may hear a booming, throbbing, or helicopter-type
noise or pressure. This is called wind buffeting. This is
a normal occurrence that can be minimized.

If you hear a wind buffeting noise with any of the
windows open, lower all of the other windows
slightly or open the moonroof

Open

■

Opening the Windows with the Remote

Opening the Windows with the Remote

If you open the windows with the remote, the
moonroof

will open automatically along with them.

Unlock

Button

* Not available on all models

179

Opening and Closing the Windows

Opening/Closing the Power Windows

Co
ntrols

To open:

Unlock the driver’s door with the

key. Within 10 seconds of returning the key to
the central position, turn the key in the unlock
direction and hold it there.

To close:

Lock the driver’s door with the key.

Within 10 seconds of returning the key to the
central position, turn the key in the lock
direction and hold it there.

Release the key to stop the windows at the
desired position. If you want further
adjustment, repeat the same operation.

■

Opening/Closing the Windows with the Key

Opening/Closing the Windows with the Key

If you open/close the windows with the key, the
moonroof

will open/close automatically along with

them.

Open

* Not available on all models

180

Co
ntrols

Moonroof

Opening/Closing the Moonroof

You can operate the moonroof when the power mode is in ON. Use the switch in
the front of the ceiling to open and close the moonroof.

■

Automatic operation

To open:

Pull the switch back firmly.

To close:

Push the switch forward firmly.

The moonroof automatically opens or closes
all the way. To stop the moonroof midway,
pull or push the switch briefly.

■

Manual operation

To open:

Pull the switch back lightly, and

hold it until the desired position is reached.

To close:

Push the switch forward lightly, and

hold it until the desired position is reached.

■

Tilting the moonroof up

To tilt:

Push on the center of the moonroof

switch.

To close:

Push the switch forward firmly,

then release.

■

Using the Moonroof Switch

Moonroof

NOTICE

Opening the moonroof in below freezing
temperature or when it is covered with snow or ice
can damage the moonroof panel or motor.

The moonroof can be operated for up to 10 minutes
after you set the power mode to VEHICLE OFF
(LOCK).
Opening either front door cancels this function.

When resistance is detected, the auto reverse
function causes the moonroof to change directions,
then stop. Auto reverse stops sensing when the
moonroof is almost closed to ensure that it fully
closes. Make sure that all objects, including fingers,
are clear of the moonroof.

You can use the remote transmitter or the key to
operate the moonroof.

Opening the Windows with the Remote

P. 178

Opening/Closing the Windows with the
Key

P. 179

WARNING

Opening or closing the moonroof on
someone’s hands or fingers can cause
serious injury.

Make sure all hands and fingers are clear of
the moonroof before opening or closing it.

Open

Tilt

* Not available on all models

181

Continued

Co
ntrols

Operating the Switches Around the Steering Wheel

POWER Button

■

Changing the Power Mode

POWER Button

POWER Button Operating Range

You can start the power system when the keyless
remote is inside the vehicle.

If the battery of the keyless remote is getting low, the
power system may not start when you press the

POWER

button. If the power system does not start,

refer to the following link.

If the Keyless Remote Battery is Weak

P. 562

The power system may also start if the keyless remote
is close to the door or window, even if it is outside the
vehicle.

ON mode:
The

POWER

button is on (in red), if the power system

is on.

Do not leave the power mode in ACCESSORY or ON
when you get out.

Operating Range

VEHICLE OFF (LOCK)

The button is off.
The power to all electrical components is turned off.

Press the button.

Without pressing
the brake pedal

ACCESSORY

The button blinks (in red).
Operate the audio system and other accessories in

this position.

The button blinks (in red).
All electrical components can be used.

182

Operating the Switches Around the Steering Wheel

POWER Button

Co
ntrols

If you leave the vehicle for 30 to 60 minutes with the transmission in

(

and the

power mode in ACCESSORY, the vehicle automatically goes into the mode to
VEHICLE OFF (LOCK) to avoid draining the 12-volt battery.

If you open the driver’s door when the power mode is set to ACCESSORY, a warning
beep sounds.

■

Automatic Power Off

■

Power Mode Reminder

183

Operating the Switches Around the Steering Wheel

POWER Button

Co
ntrols

When the power mode is set to any mode
other than OFF and you remove the keyless
remote from the vehicle and shut the door, an
alarm will sound. If the alarm continues to
sound, place the keyless remote in another
location.

■

When the power mode is in
ACCESSORY

The alarm will sound from outside the vehicle.

■

When the power mode is in ON

An alarm will sound both inside and outside
the vehicle. In addition, a warning indicator
will appear on the instrument panel.

■

Keyless Remote Reminder

Keyless Remote Reminder

When the keyless remote is within the system’s
operational range, and the driver’s door is closed, the
warning function cancels.

If the keyless remote is taken out of the vehicle after
the power system has been turned on, you can no
longer change the

POWER

button mode or restart

the power system. Always make sure if the remote is
in your vehicle when you operate the

POWER

button.

Removing the keyless remote from the vehicle
through a window does not activate the warning
buzzer.

Do not put the keyless remote on the dashboard or in
the glove box. It may cause the warning buzzer to go
off. Under some other conditions that can prevent
the vehicle from locating the remote, the warning
buzzer may also go off even if the remote is within
the system’s operational range.

184

Operating the Switches Around the Steering Wheel

Turn Signals

Co
ntrols

Turn Signals

The turn signals can be used when the power
mode is in ON.

■

(A): Turn signal

Push the lever up or down based on the
direction you want to turn, and the turn signal
will blink.

■

(B): One-touch turn signal

When you lightly push the lever up or down
and release it, the turn signal will blink 3
times.

(A): Turn signal

The turn signal indicator on the instrument panel will
blink when the external turn signal blinks.

Indicators

P. 82

(A)

(B)

185

Operating the Switches Around the Steering Wheel

Light Switches

Continued

Co
ntrols

Light Switches

Rotating the light switch turns the lights on
and off, regardless of the power mode
setting.

■

High beams

Push the lever forward until you hear a click.

■

Low beams

When in high beams, pull the lever back to
return to low beams.

■

Flashing the high beams

Pull the lever back, and release it.

■

Manual Operation

Light Switches

If you leave the power mode in VEHICLE OFF (LOCK)
while the lights are on, a chime sounds when the
driver’s door is opened.

When the lights are on, the lights on indicator in the
instrument panel will be on.

Lights On Indicator

P. 95

Do not leave the lights on when the power system is
off because it will cause the 12-volt battery to
discharge.

If you sense that the level of the headlights is
abnormal, have the vehicle inspected by a dealer.

High Beams

Flashing the high beams

Low Beams

Turns on parking, side marker,
tail, and rear license plate lights

Turns on headlights, parking, side
marker, tail, and rear license plate
lights

Operating the Switches Around the Steering Wheel

Light Switches

186

Co
ntrols

Automatic lighting control can be used when
the power mode is in ON.

When the light switch is in

AUTO

, the

headlights and other exterior lights will switch
on and off automatically depending on the
ambient brightness.

The headlights come on when you unlock a
door in dark areas with the headlight switch in

AUTO

Once you lock the door, the headlights
will go off.

■

Automatic Operation (automatic lighting control)

Automatic Operation (automatic lighting control)

We recommend that you turn on the lights manually
when driving at night, in a dense fog, or in dark areas
such as long tunnels or parking facilities.

The light sensor is in the location shown below.
Do not cover this light sensor with anything;
otherwise, the automatic lighting system may not
work properly.

Light Sensor

Models without automatic

intermittent wipers

Light Sensor

Models with automatic

intermittent wipers

187

Operating the Switches Around the Steering Wheel

Light Switches

Co
ntrols

The headlights automatically come on when the wipers are used several times within
a certain number of intervals with the headlight switch in

AUTO

The headlights automatically go off a few minutes later if the wipers are stopped.

The headlights, all other exterior lights, and the instrument panel lights turn off 15
seconds after you set the power mode to VEHICLE OFF (LOCK), take the remote with
you, and close the driver’s door.

If you set the power mode to VEHICLE OFF (LOCK) with the headlight switch on, but
do not open the door, the lights turn off after 10 minutes (3 minutes, if the switch
is in the

AUTO

position).

The lights turn on again when you unlock or open the driver’s door. If you unlock
the door, but do not open it within 15 seconds, the lights go off. If you open the
driver’s door, you will hear a reminder chime alerting you that the lights are on.

■

Headlight Integration with Wipers

■

Automatic Lighting Off Feature

Automatic Operation (automatic lighting control)

You can adjust the auto light sensitivity as follows:

Customized Features

P. 326

Setting

The exterior lights come on

when the ambient light is at

Max