Honda Crosstour (2015 year). Instruction

432

When Driving

Cruise Control

Driving

Cruise Control

Maintains a constant vehicle speed without having to keep your foot on the
accelerator. Use cruise control on freeways or open roads where you can travel at a
constant speed with little acceleration or deceleration.

Cruise Control

It may not be possible to maintain a constant speed
when driving uphill or downhill.

When not using cruise control:
Turn off cruise control by pressing the CRUISE
button.

WARNING

Improper use of the cruise control can lead
to a crash.

Use the cruise control only when traveling
on open highways in good weather.

■

Shift positions for cruise control:

(

D or

(

D or

(

Models without paddle shifters

Models with paddle shifters

When to use

Always keep sufficient distance
between you and the vehicle in
front of you.

■

Vehicle speed for cruise control:
Desired speed in a range above
roughly 25 mph (40 km/h) ~

How to use

CRUISE MAIN is on in the
instrument panel.
Cruise control is ready to use.

■

Press the

CRUISE

button on

the steering wheel.

433

When Driving

Cruise Control

Continued

Driving

Take your foot off the pedal and press the –/SET button when you reach the desired
speed.

The moment you release the –/SET button, the set speed is fixed, and cruise control
begins. The CRUISE CONTROL indicator comes on.

■

To Set the Vehicle Speed

–/SET

Button

On when cruise control begins

Press and release

When Driving

Cruise Control

434

Driving

Increase or decrease the vehicle speed using the RES/+ or –/SET buttons on the
steering wheel.

• Each time you press the button, the vehicle speed is increased or decreased by

about 1 mph (1.6 km/h).

• If you keep the button pressed, the vehicle speed increases or decreases until you

release it. This speed is then set.

To cancel cruise control, do any of the
following:
• Press the CANCEL button.
• Press the CRUISE button.
• Depress the brake pedal.
The CRUISE CONTROL indicator goes off.

■

To Adjust the Vehicle Speed

To Adjust the Vehicle Speed

You can set the vehicle speed using the –/SET button
on the steering wheel when adjusting the speed with
the accelerator and brake pedals.

■

To Cancel

To decrease speed

To increase speed

To Cancel

Resuming the prior set speed:
After cruise control has been canceled, you can still
resume the prior set speed by pressing the RES/+
button while driving at a speed of at least 25 mph (40
km/h) or more.

You cannot set or resume in the following situations:

•

When vehicle speed is less than 25 mph (40 km/h)

•

When the CRUISE button is turned off

At vehicle speeds of 22 mph (35 km/h) or less, cruise
control is canceled automatically.

CRUISE
Button

CANCEL
Button

435

When Driving

Forward Collision Warning (FCW)

Continued

Driving

Forward Collision Warning (FCW)

Alerts you when it detects the possibility of your vehicle colliding with the vehicle in
front of yours.

If the system determines a collision is possible, it gives both visual and audible alerts.

Take appropriate action to prevent a collision (apply the brakes, change lanes,
etc.).

■

How the system works

The system may give warnings of potential collisions when your vehicle speed is
above 10 mph (15 km/h).

Forward Collision Warning (FCW)

Important Safety Reminder
FCW cannot detect all objects ahead and may not
detect a given object; accuracy of the system will vary
based on weather, speed and other factors. FCW
does not include a braking function. It is always your
responsibility to safely operate the vehicle and avoid
collisions.

You can change the Forward Collision Warning
Distance setting or turn the system on and off.

2 Customized Features

P. 280

The camera is shared with Lane Departure Warning
(LDW).

2 LDW Camera P. 440

LONG

NORMAL

SHORT

Your Vehicle

Vehicle Ahead

You can set Long, Normal or Short for when warnings start:

* Not available on all models

When Driving

Forward Collision Warning (FCW)

436

Driving

Forward Collision Warning (FCW)

Never apply a film or attach any objects to the
windshield that could obstruct the FCW camera’s
field of vision.
Scratches, nicks, and other damage to the windshield
within the FCW camera’s field of vision can cause the
system to operate abnormally. If this occurs, we
recommend that you replace the windshield with a
genuine Honda replacement windshield. Making
even minor repairs within the camera’s field of vision
or installing an aftermarket replacement windshield
may also cause the system to operate abnormally.
After replacing the windshield, have a dealer
recalibrate the camera. Proper calibration of the FCW
camera is necessary for the system to operate
properly.

Beep

Camera-based system

The camera is located
behind the rearview mirror.

The beeper sounds and
the FCW indicator blinks
until a possible collision
is avoided.

* Not available on all models

Continued

437

When Driving

Forward Collision Warning (FCW)

Driving

■

Automatic shutoff

FCW may automatically shut itself off and the FCW indicator comes and stays on
when:
• The temperature inside the system is high.
• The windshield is blocked by dirt, mud, leaves, wet snow, etc.

Once the conditions that caused FCW to shut off improve or are addressed (e.g.,
cleaning), the system comes back on.

Automatic shutoff

To help reduce the likelihood that high interior
temperatures will cause the camera system to shut
off, when parking, find a shady area or face the front
of the vehicle away from the sun.

If you use a reflective sun shade, do not allow it to
cover the camera housing. Covering the camera can
concentrate heat on the camera.

If the CAMERA HOT message appears:

•

Use the climate control system to cool down the
interior and, if necessary, the defroster mode when
windows are fogged.

•

Start driving the vehicle to lower the windshield
temperature, which cools down the area around
the FCW system.

438

When Driving

Forward Collision Warning (FCW)

Driving

FCW may not activate or may not detect a vehicle in front of your vehicle, and may activate even when you are aware of a vehicle ahead
of you, or when there is no vehicle ahead under the following conditions.

■

FCW Limitations

Condition

●

The distance between your vehicle and the vehicle ahead of you is too short.

●

A vehicle cuts in front of you at a slow speed, and it brakes suddenly.

●

A vehicle suddenly crosses in front of you.

●

When either your vehicle or the vehicle ahead of you accelerates rapidly.

●

The vehicle ahead of you is a motorcycle, a small vehicle, or a unique vehicle such as a tractor.

●

When you drive off-road or on a mountain road, or curved and winding road for an extended period that makes it difficult for the camera to properly
detect a vehicle in front of you.

●

When there are pedestrians or animals in front of your vehicle.

●

When you drive in bad weather (rain, fog, etc.).

●

A heavy load in the rear or modifications to the suspension tilts your vehicle.

●

An abnormal tire condition is detected (wrong tire size, flat tire, etc.).

●

When the windshield is blocked by dirt, mud, leaves, wet snow, etc.

●

When the temperature inside the system is high.

●

A sudden change between light and dark such as an entrance or exit of a tunnel.

●

You drive into the sunlight (e.g. at dawn or dusk).

●

When the windshield is dirty or cloudy.

●

When streetlights are perceived as the taillight of a vehicle in front of yours.

●

When driving at night, the vehicle ahead of you is running with either taillight bulb burned out.

●

When you drive in the shadows of trees, buildings, etc.

●

When your vehicle is towing a trailer.

439

When Driving

Lane Departure Warning (LDW)

Continued

Driving

Lane Departure Warning (LDW)

Alerts you when the system detects a possibility of your vehicle unintentionally
crossing over detected lane markings.

If your vehicle is getting too close to detected
left or right side lane markings without a turn
signal activated, LDW will give audible and
visual alerts.

The beeper sounds and the LDW indicator
blinks, letting you know that you need to take
appropriate action.

■

How the System Works

Lane Departure Warning (LDW)

Important Safety Reminder
Like all assistance systems, LDW has limitations.
Over-reliance on LDW may result in a collision. It is
always your responsibility to keep the vehicle within
your driving lane.

LDW only alerts you when lane drift is detected
without a turn signal in use. LDW may not detect all
lane markings or lane departures; accuracy will vary
based on weather, speed and lane marker condition.
It is always your responsibility to safely operate the
vehicle and avoid collisions.

* Not available on all models

When Driving

Lane Departure Warning (LDW)

440

Driving

The system begins to search for lane markings when all the following conditions are met:
• The vehicle is traveling between 40 and 90 mph (64 and 145 km/h).
• The vehicle is on a straight or slightly curved road.
• The turn signals are off.
• The brake pedal is not depressed.

The camera is located behind the rearview
mirror.

Press the LDW button to turn the system on
and off.

The indicator in the button comes on
when the system is on.

■

How the System Activates

■

LDW Camera

How the System Activates

LDW may automatically shut off and the LDW
indicator comes and stays on.

2 Indicators P. 77

LDW Camera

Never apply a film or attach any objects to the
windshield that could obstruct the LDW camera’s
field of vision.
Scratches, nicks, and other damage to the windshield
within the LDW camera’s field of vision can cause the
system to operate abnormally. If this occurs, we
recommend that you replace the windshield with a
genuine Honda replacement windshield. Making
even minor repairs within the camera’s field of vision
or installing an aftermarket replacement windshield
may also cause the system to operate abnormally.
After replacing the windshield, have a dealer
recalibrate the camera. Proper calibration of the LDW
camera is necessary for the system to operate
properly.

Do not place an object on the top of the instrument
panel. It may reflect onto the windshield and prevent
the system from detecting lane lines properly.

To help reduce the likelihood that high interior
temperatures will cause the camera system to shut
off, when parking, find a shady area or face the front
of the vehicle away from the sun.

LDW Camera

■

LDW On and Off

LDW Button

Indicator

441

When Driving

Lane Departure Warning (LDW)

Driving

LDW may not activate or may not recognize lanes, and may activate even when
keeping in the middle of a lane under the following conditions.

■

LDW Limitations

Condition

●

When you drive in bad weather (rain, fog, etc.).

●

A heavy load in the rear or modifications to the suspension tilts your vehicle.

●

An abnormal tire condition is detected (wrong tire size, flat tire, etc.).

●

When the windshield is blocked by dirt, mud, leaves, wet snow, etc.

●

When the temperature inside the system is high.

●

A sudden change between light and dark such as an entrance or exit of a tunnel.

●

You drive into the sunlight (e.g. at dawn or dusk).

●

When the windshield is dirty or cloudy.

●

When you drive in the shadows of trees, buildings, etc.

●

When your vehicle is towing a trailer.

●

When you drive on a wet road surface following another vehicle.

The camera may perceive the tire tracks in the water as lane lines.

●

When there is snow or wheel tracks on the side of the road.

●

When the road has many repaired area or an erased lane line.

●

When the vehicle is running over painted signs or crosswalk markings.

●

When you drive in a lane with worn-out lane markings.

LDW Camera

If you use a reflective sun shade, do not allow it to
cover the camera housing. Covering the camera can
concentrate heat on the camera.

If the CAMERA HOT message appears:

•

Use the climate control system to cool down the
interior and, if necessary, the defroster mode when
windows are fogged.

•

Start driving the vehicle to lower the windshield
temperature, which cools down the area around
the LDW camera.

442

When Driving

Vehicle Stability Assist (VSA®), aka Electronic Stability Control (ESC), System

Driving

Vehicle Stability Assist (VSA®), aka Electronic
Stability Control (ESC), System

VSA® helps to stabilize the vehicle during cornering if the vehicle turns more or less
than what was intended. It also assists in maintaining traction on slippery surfaces.
It does so by regulating engine output and selectively applying the brakes.

When VSA® activates, you may notice that the
engine does not respond to the accelerator.
You may also notice some noise from the
hydraulic system. You will also see the
indicator blink.

■

VSA® Operation

Vehicle Stability Assist (VSA®), aka Electronic Stability Control
(ESC), System

The VSA® may not function properly if tire type and
size are mixed. Make sure to use the same size and
type of tire, and the air pressures as specified.

When the VSA® indicator comes on and stays on
while driving, there may be a problem with the
system. While this may not interfere with normal
driving, have your vehicle checked by a dealer
immediately.

VSA® cannot enhance stability in all driving situations
and does not control the entire braking system. You
still need to drive and corner at speeds appropriate
for the conditions and always leave a sufficient
margin of safety.

The main function of the VSA® system is generally
known as Electronic Stability Control (ESC). The
system also includes a traction control function.

VSA® System Indicator

443

When Driving

Vehicle Stability Assist (VSA®), aka Electronic Stability Control (ESC), System

Driving

This button is on the driver side control panel.
To turn the VSA® system on and off, press and
hold it until you hear a beep.

VSA® will stop and the indicator will come on.

To turn it on again, press the

(VSA® OFF)

button until you hear a beep.

VSA® is turned on every time you start the
engine, even if you turned it off the last time
you drove the vehicle.

■

VSA® On and Off

Vehicle Stability Assist (VSA®), aka Electronic Stability Control
(ESC), System

Without VSA®, your vehicle will have normal braking
and cornering ability, but it will not have VSA®
traction and stability enhancement.

In certain unusual conditions when your vehicle gets
stuck in shallow mud or fresh snow, it may be easier
to free it with the VSA® temporarily switched off.

When the VSA® system is off, the traction control
system is also off. You should only attempt to free
your vehicle with the VSA® off if you are not able to
free it when the VSA® is on.

Immediately after freeing your vehicle, be sure to
switch VSA® on again. We do not recommend driving
your vehicle with the VSA® and traction control
systems switched off.

If the low tire pressure, or TPMS indicator comes on
or blinks, the VSA® system comes on automatically. In
this case, you cannot turn the system off by pressing

the

button.

You may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.

VSA® OFF Indicator

444

When Driving

LaneWatch

Driving

LaneWatch

Is an assistance system that allows you to check the passenger side rear areas
displayed on the audio/information screen when the turn signal is activated to the
passenger’s side. A camera in the passenger side door mirror monitors these areas
and allows you to check for vehicle, in addition to your visual check and use of the
passenger door mirror. You can also keep the system on for your convenience while
driving.

LaneWatch

Important Safety Reminder
Like all assistance systems, LaneWatch has limitations.
Over reliance on LaneWatch may result in a collision.

The LaneWatch function can be affected by weather,
lighting (including headlights and low sun angle),
ambient darkness, camera condition, and loading.

The LaneWatch camera view is restricted. Its unique
lens makes objects on the screen look slightly
different from what they are.

LaneWatch display does not come on when the shift
lever is in

(

The LaneWatch may not provide the intended display of
traffic to the side and rear under the following conditions:

•

Your vehicle’s suspension has been altered,
changing the height of the vehicle.

•

Your tires are over or under inflated.

•

Your tires or wheels are of varied size or construction.

WARNING

Failure to visually confirm that it is safe to
change lanes before doing so may result in
a crash and serious injury or death.

Do not rely only on LaneWatch while
driving.
Always look in your mirrors, to either side
of your vehicle, and behind you for other
vehicles before changing lanes.

Camera

Audio/Information Screen

Move the turn signal
lever to the passenger
side.

Press the LaneWatch
button.

Pull the turn signal
lever back.

Press the LaneWatch
button again.

The passenger side view
display appears on the
audio/information screen.

The system activates when you:

The system deactivates when you:

* Not available on all models

445

When Driving

LaneWatch

Driving

■

Customizing the LaneWatch settings

You can customize the following items using the audio/information screen.
• Show with Turn Signal: Selects whether LaneWatch monitor comes on when

you operate the turn signal light lever.

• Reference Lines: Selects whether the reference lines appear on the LaneWatch

monitor.

• Next Maneuver Pop up

: Selects whether a turn direction screen of the

navigation system interrupts the LaneWatch display.

• Display: Adjusts display settings.

2 Customized Features

P. 280

■

Reference Lines

Three lines that appear on the screen can give
an idea of how far the vehicles or objects on
the screen are from your vehicle, respectively.
If an object is near line 1 (in red), it indicates
that it is close to your vehicle whereas an
object near line 3 farther away.

LaneWatch

For proper LaneWatch operation:

•

The camera is located in the passenger side door
mirror. Always keep this area clean. If the camera
lens is covered with dirt or moisture, use a soft,
moist cloth to keep the lens clean and free of
debris.

•

Do not cover the camera lens with labels or stickers
of any kind.

•

Do not touch the camera lens.

Reference Lines

The area around the reference line 1 (red) is very close
to your vehicle. As always, make sure to visually
confirm the safety of a lane change before changing
lanes.

The distance between your vehicle and lines 1, 2 and
3 on the screen vary depending on road condition
and vehicle loading. For example, reference lines on
the screen may seem to appear closer than the actual
distances when the rear of your vehicle is more
heavily loaded.

Consult a dealer if:

•

The passenger side door mirror, or area around it is
severely impacted, resulting in changing the
camera angle.

•

The LaneWatch display does not come on at all.

* Not available on all models

446

When Driving

Tire Pressure Monitoring System (TPMS)

Driving

Tire Pressure Monitoring System (TPMS)

Monitors the tire pressure while you are
driving. If your vehicle’s tire pressure becomes
significantly low, the low tire pressure
indicator comes on.

Tire Pressure Monitoring System (TPMS)

Conditions such as low ambient temperature and
altitude change directly affect tire pressure and can
trigger the low tire pressure indicator to come on.

2 If the Low Tire Pressure Indicator Comes

On P. 537

Tire pressure checked and inflated in:

•

Warm weather can become under-inflated in
colder weather.

•

Cold weather can become over-inflated in warmer
weather.

The low tire pressure indicator will not come on as a
result of over inflation.

447

When Driving

Tire Pressure Monitoring System (TPMS) - Required Federal Explanation

Continued

Driving

Tire Pressure Monitoring System (TPMS) - Required
Federal Explanation

Each tire, including the spare (if provided), should be checked
monthly when cold and inflated to the inflation pressure
recommended by the vehicle manufacturer on the vehicle placard
or tire inflation pressure label.

(If your vehicle has tires of a different size than the size indicated
on the vehicle placard or tire inflation pressure label, you should
determine the proper tire inflation pressure for those tires.)

As an added safety feature, your vehicle has been equipped with
a tire pressure monitoring system (TPMS) that illuminates a low
tire pressure telltale

when one or more of your tires is significantly under-inflated.

Accordingly, when the low tire pressure telltale illuminates, you
should stop and check your tires as soon as possible, and inflate
them to the proper pressure.

Driving on a significantly under-inflated tire causes the tire to
overheat and can lead to tire failure. Under-inflation also reduces
fuel efficiency and tire tread life, and may affect the vehicle’s
handling and stopping ability.

U.S. models

Honda Crosstour (2015 year). Instruction - part 28