269

6

Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment

of the driver airbag assembly, connect them with the two terminals of the battery removed from the

vehicle and deploy the airbag (see the figure below).

7

The deployed driver airbag assembly shall be scrapped according to the scrapping procedures.

(3) Deploy outside the vehicle

NOTICE:

Keep the airbag over 6m away from a obstacle or person and deploy the airbag in an open flat area.

1

Disconnect the positive (+) and negative (-) terminal cables from the battery and remove the battery

from the vehicle.

2

The airbag assembly shall be deployed according to the following procedures.

(4) Driver airbag assembly

1

Remove the driver airbag assembly from the vehicle.

Vehicle Cover

Wire Harness 

for Deployment

NOTICE

Make sure there is no man inside or near the vehicle and then carry out the operations.

After the driver airbag is deployed, the gas generator is of high temperature. Keep it for 30 minutes until it

gets cool for use.

If the driver airbag assembly cannot be deployed, discuss the problem with the local Geely service station.

NOTICE

Work must be started 60s after removal of the battery.

NOTICE

When the connector is not connected, the terminals of the driver airbag assembly will be short circuited

automatically, preventing the airbag from being deployed unexpectedly. If the airbag is deployed unexpectedly,

the deployed surface should face up. It should be kept on a flat surface without any other items on it.

270

2

Prepare two 6m plus wire harnesses for deployment, connect the other two ends to avoid unexpected

deployment in case of static electricity (see the figure below).

3

Touch the body of the vehicle with hands for static electricity elimination.

NOTICE:

The above-mentioned procedures can prevent the unexpected deployment due to static electricity and shall

therefore be performed strictly.

4

Cut off the wire harnesses of the driver airbag assembly and connect them with the two wire harnesses

for deployment, and make sure to wrap up the connecting location with insulating tape for insulation (see

the figure below).

5

Install the unused bolts on to the inside bolt of the driver airbag assembly, and tie a thick wire securing the

wheel rim.

6

Pass the deployment wire harness of the driver airbag assembly through an old tire with rim, and fix

upwards the driver airbag assembly by means of the wire connected to the bolts, etc (see the figure

below).

Wire Harness  for Deployment

Short Circuit Locatio

n

6m plus

Passenger Airbag

Wire Harness 
for Deployment

Short 
Circuit 
Location

Insulating Tape

Airbag Assembly

Wire Harness 
for Deployment

271

7

Put three old tires without hubs onto the tire used to fix the driver airbag assembly (see the figure below).

8

Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment

of the driver airbag assembly, connect with the two terminals of the battery removed from the vehicle

and deploy the airbag (see the figure below).

9

the deployed driver airbag assembly shall be scrapped according to the scrapping procedures.

Wire Harness for Deployment

Old Wheels 
without Hub

Wire Harness 
for Deployment

NOTICE

Make sure to deploy the driver airbag assembly when there is no person close by.

After the driver airbag is deployed, the gas generator is of high temperature. Keep it for over 30 minutes

until it gets cool for use

272

Chapter 8 MK-20 ABS System

Section 1 ABS Diagnosis

I. Check the ABS Warning Light

1. Check the ABS Warning Light goes on as the following:

1

Turn the ignition switch to ON, the ABS Warning Light goes on for about 1.7 seconds and then goes off.

2

If the above condition is not satisfied, it indicates that there is a fault, please check the DTC.

3

If the warning light does not light up at all, refer to the Non-DTC fault inspection table.

II. The Reading of the information status

After connecting the scan meter, turn the ignition switch to¡°ON¡±, select the function menu item 01, press

OK to confirm, the screen will display the following information:

1. ECU drawing number and its version:

ABS   MK20 IE

2. Code  01901

III. Read and Clear the DTC

1. After selecting the "02 Read DTC" in the function menu, it displays the total amount of the fault, if there

is no DTC, then it displays no DTC. Then, press OK button to proceed to next page to review the DTC

and its description. Generally, there is a P or O before the DTC, indicating that it is a Persistent fault or

Occasional fault. Persistent fault remains existing all the time, while the Occasional fault can be cleared

and is only able to reoccur during the driving.

Note:

The reading of the DTC can not be quitted middle way, you can return to the function menu only

after reading all the DTC.

Clear DTC

2. Select function menu item 05, press OK button to clear the DTC, if the DTC can not be cleared, it

indicates that the DTC represent exist all the time, if the saved DTC can be cleared, it indicates that it is

occasional fault can only be detected during the driving.