117

Section 2  Rear Suspension

Components

LR Strut 

Assembly

LR ABS 

Sensor 

W

ire 

Harness

LR Brake

LR Brake Pipe

Clip

Clip

RR Strut 

Assembly

Clip

RR 

ABS Sensor 

W

ire Harness

RR Brake Hosex2

No. 2 

T

ransverse 

Arm

Left T

railing 

Rod 

Assembly

Body

Body

Body

Body

No. 1 

T

ransverse 

Arm

No. 1 Rocker 

Arm

Clip

RR Brake Pipe

RR Brake Hose

RR Brake

Right T

railing 

Rod 

Assembly

Rear Stabilizer Bar 

Assembly

No. 2 

T

ransverse 

Arm

Rear Stabilizer Bar Retainer 

Rod Components

118

Section 3 Rear Wheel Alignment

Inspection

1. Inspect tire

Standard inflation pressure: 220 Kpa

2. Inspect rear wheel toe-in

If the rear wheel toe-in is not within the specification, adjust it via rear

wheel toe-in adjusting cam.

3. Inspect the camber

Notice: If the camber is not within the specification, check the suspension parts for damage/low

performance. Replace it if necessary.

Toe-in

C - D: 1

～

 5 mm

C a m b e r

- 20 ´±   3 0 ´

Front

No. 2 Transverse Arm Assembly 

Rear Wheel Toe-In 
Adjusting Panel

Rear Wheel Toe-In 
Adjusting Plate

No. 2 Transverse
Arm Assembly 

No. 1 Transverse 
Arm Assembly 

No. 1 Transverse
Arm Assembly 

Rear Wheel Toe-In 
Adjusting Cam

Rear Wheel Toe-In 
Adjusting Cam

Body Bottom Plate

119

Section 4 Left & Right Rear Strut Assembly

Components

Replacement

1. Remove the rear wheel

2. Remove ABS sensor

(1) Remove ABS rear wheel sensor retaining bolt. Remove the sensor.

(2) Remove the retaining bolt of ABS rear wheel sensor on rear shock absorber bracket

3. Separate brake pipe and rear strut assembly

Remove the elastic clip on the pipeline bracket attaching the brake pipeline

Cushion (Dumper)

Dust Prevent 
Sleeve

Rear Suspension 
Spring Lower 
Insulator

Rear Left 
Shock Absorber 

Upper Mount 

Cushion

Upper Mount

Rear Suspension 

Spring Insulator

Rear Suspension Conical Spring

120

4. Remove the left and right rear strut assembly

(1) Remove the threaded connect of the rear strut assembly and rear brake assembly

(2) Remove the 3 nuts attaching the rear suspension upper mount to the body

Caution: reliable object shall be used to support the rear brake assembly! Make sure that the

brake pipeline is not affected or damaged!

5. Disassembly the left, right rear strut assembly

(1)  Set the rear strut assembly with special tool. Remove the nut on the top of the

rear shock absorber piston

Caution: The spring may rebound!

(2) Remove the rear suspension upper mount, rear suspension upper mount cushion,

rear suspension spring upper insulator, rear suspension spring, rear shock absorber

cushion, rear shock absorber dust preventing sleeve, rear suspension spring lower insulator in order

6. The assembly is in the reverse order of the disassembly.

Caution:

(1) when installing the nut on the shock absorber piston rod upper end, use special fixture

and be careful that the spring may rebound!

Torque : 32~38N.m

(2) Rear strut assembly to body thread torque : 32~38 N.m

(3) Strut assembly to rear brake assembly thread torque : 81~96 N.m

(4) Install the ABS rear wheel sensor and the secure the signal wire

(5) When securing the brake line, make sure that the brake line does not interfere with

other parts

(6) Wheel nut torque : 95~115N.m

(7) Check the brake system for leakage, bleed air in the brake system as necessary

(8) Check whether the ABS signal is normal

(9) Check rear wheel alignment, adjust it as necessary