FE11-1807b

3.

With a double-pipe gun evenly apply glass sealant to the
window glass edge to make sure that the sealant width is
even.

FE11-1803b

4.

With the help of an assistant, install the windshield glass
to the windshield frame.

5.

Press the windshield glass to bond the adhesive to the
seal  strip,  the  windshield  and  the  windshield  frame  to
retain the windshield.

6.

Let adhesive dry 24 h.

7.

spray water onto the windshield to check for water leaks.
If it leaks, dry the windshield and apply adhesives to the
leaking location. If it still leaks, remove the windshield and
repeat the entire repair procedure.

8.

Install the inside rearview mirror.

9.

Install the left / right A pillar garnish moldings.

10. Install the air inlet duct.

11. Install the wiper arms.

Body Electric

Glasses / Windows / Mirrors

11-209

11.5.8.10 Rear Window Replacement (Sedan)

Removal Procedure

1

FE11-1808b

1.

Remove  the  battery  negative  cable.  Refer  to

2.11.8.1

 

Battery Disconnection

.

2.

Remove the left / right rear upper quarter panel. Refer to

12.9.1.5

 

Rear  Quarter  Upper  Trim  Panel  Replacement

(Sedan)

.

3.

Remove  the  rear  parcel  shelf.  Refer  to 

12.9.1.7

 

Rear

Parcel Shelf Replacement (Sedan)

.

4.

Disconnect the rear window defroster electrical connector
(1).

FE11-1802b

5.

Cut the rear window glass adhesive with a thin steel wire.

Note

Wrap both end of the fine steel wire around a wood
handle, operate by with two people to facilitate the
removal.

FE11-1809b

6.

Remove  the  rear  window  glass  from  the  rear  window
frame.

Note

It takes two people to complete this step.

11-210

Glasses / Windows / Mirrors

Body Electric

FE11-1804b

7.

Removed the adhesive on the rear window glass with a
blade.

8.

Removed the adhesive on the rear window frame with a
blade.

9.

Clean  the  windshield  inner  surface  with  a  cloth  stained
soaked  with  industrial  ethanol  and  water  mixture  with
50/50 volume ratio.

Installation Procedure:

FE11-1806b

1.

Spray the dedicated Geely glass sealant, with 8 mm (0.3
in) width 8 mm (0.3 in) height.

FE11-1807b

2.

With a double-pipe gun evenly apply glass sealant to the
window glass edge to make sure that the sealant width is
even.

Body Electric

Glasses / Windows / Mirrors

11-211

FE11-1809b

3.

With the help of an assistant, install the rear window glass
to the rear window frame.

4.

Press the rear window glass to bond the adhesive to the
seal  strip,  the  rear  window  glass  and  the  rear  window
frame to retain the rear window.

5.

Let adhesive dry 24 h.

6.

Spray water onto the rear window to check for water leaks.
If it leaks, dry the rear window and apply adhesives to the
leaking location. If it still leaks, remove the rear window
and repeat the entire repair procedure.

7.

Connect  the  rear  window  defroster  wiring  harness
connector.

8.

Install the rear parcel shelf.

9.

Install left / right rear upper quarter panel.

10. Connect the battery negative cable.

11.5.8.11 

Rear 

Window 

Replacement

(Hatchback)

Removal Procedure

1

2

FE11-1810c

1.

Remove  the  battery  negative  cable.  Refer  to

2.11.8.1

 

Battery Disconnection

.

2.

Remove the wiper arm. Refer to 

11.6.8.3

 

Rear Wiper Arm

Replacement (Hatchback)

.

3.

Remove  the  hatchback  trim  panel.  Refer  to

12.9.1.15

 

Hatchback  Inner  Trim  Panel  Replacement

(Hatchback)

.

4.

Remove  the  high  mounted  brake  lamp.  Refer  to
the

11.4.8.10

 

High  Mounted  Brake  Lamp  Replacement

(Hatchback)

.

5.

Disconnect Defroster harness connectors (1) and (2).

11-212

Glasses / Windows / Mirrors

Body Electric