Test Content

Testing Requirements

DTC

Cause

Right Turn Lamp Switch Circuit

B2281

Right turn signal
lamp switch circuit is
short to ground.

Automatic  Headlamp  Switch
Circuit

B1695

Automatic
headlamp switch
circuit is short to
power supply.

Headlamps Switch Circuit

B2598

Headlamp circuit
and headlamp relay
circuit are short to
power supply.

Park Lamp Switch Circuit

1. Shift lever is in neutral.

2. Headlamp switch is at OFF position.

B1697

Park lamp circuit
and park lamp relay
circuit are short to
power supply.

Key Insert Switch Circuit

1. Ignition key is not inserted.

2. Rear  window  defroster  switch  and  emergency

alarm push button are in natural.

B1093

Key insert switch
circuit is short to
ground.

Rear Window Defroster Switch
Circuit

B1343

Rear window
defroster switch
circuit is short to
ground.

Emergency 

Alarm 

Switch

Circuit

B1875

Emergency alarm
switch circuit is
short to ground.

Vehicle Control System

Computer / Integrated Systems

10-21

10.2.5 Removal and Installation
10.2.5.1 BCM replacement

Refer to 

11.10.8.1

 

BCM Replacement

.

10-22

Computer / Integrated Systems

Vehicle Control System

10.3 Programming and Set Up

10.3.1 Programming and Set Up

1. Programming Note

Before control module programming, make sure the following
conditions are met:

A. Vehicle System Voltage

a. Charging system should have no trouble. In the control

module  programming,  firstly  rule  out  the  charging
system failure.

b. Battery  voltage  should  be  greater  than  12  V  but  less

than 16 V. If the battery voltage is too low, before the
control  module  programming  the  battery  must  be
charged.

c. Do  not  connect  the  vehicle  battery  charger  to  the

battery.  Incorrect  or  the  battery  charger  or  system
voltage caused voltage fluctuations will lead to program
failure or control module damage.

d. Turn off or disable all electrical load, battery load, such

as the following components:

•

Interior Lamps

•

Daylight Lamps (If equipped)

•

Heating,  Ventilation  and  Air-Conditioning  (HVAC)
System

•

Engine Cooling Fans, Radio, etc.

B. Ignition switch must be placed in the correct location. In the

programming  process,  do  not  change  the  ignition  switch
position, unless the diagnostic unit has instructions.

C. Make sure that all tools connections are solid, including the

following components and circuits:

a. Scan Tool

b. Data Link Connector (DLC) Connections

c. Power Supply Circuit

D. Do  not  disturb  programming  tool  harness.  Unexpected

interruption of programming will lead to program failure or
control module damage.

2.  Programming  and  Set  Up  After  ECM
Replacement

After  ECM  replacement,  read  the  ECM  security  procedures.
Refer to 

2.5.7.10

 

Replaced ECM Programming

.

3. Programming and Setup After ABS Module
Replacement

This device does not require programming or setup.

4. Module Programming and Setup After TPMS
Replacement

Replace the TPMS module, or TPMS sensor. TPMS module
and  sensors  need  to  learn  specific  steps  to  refer
to

6.7.6.1

 

Sensor Learn

.

5. Instrument Cluster Programming and Set Up
After Replacement

This device does not require programming or setup.

6.  Programming  and  Set  Up  After  BCM
Replacement

After replacing BCM, the remote key must be reset, detailed
steps are as follows:

Lift anti-theft case, open the driver door. Turn the key from OFF
to ON 6 times in 10 s. the last stop is at the OFF position. At
this time, the anti-theft indicator light enters the learn mode.
Hold down any key on the remote control device. If the anti-
theft  light  flashes  once,  it  indicates  a  successful  learn.  Four
keys can be learned in a row. 10 s after the completion of four
keys, or after learning one key and the ignition is at "ON". End
for each learn, the previous key id will be replaced.

7. Anti-theft Control Module Programming and
Setup After Replacement

After replacing engine anti-theft control module, read security
program into the module. Refer to 

2.5.7.11

 

Replaced Anti-theft

Module and ECM Programming

.

8. Ignition Key Programming and Setup After
Replacement

Engine anti-theft system can learn up to five keys. For detailed
steps. Refer to 

2.5.7.7

 

Replaced Key Programming

9. Remote Key Programming and Setup After
Replacement

Refer to

10.3.1

 

.

10.  Roof  Module  Motor  Programming  and
Setup After Replacement

After  replacing  the  roof  motor  module,  initialize  the  sunroof
module  motor.  For  detailed  steps.  Refer  to 

11.8.7.3

 

Sunroof

Initialization

.

Vehicle Control System

Programming and Set Up

10-23

11. Reverse Radar Module Programming and
Setup After Replacement

This device does not require programming or setup.

12. 

Airbag 

control 

module 

Module

Programming and Setup After Replacement

This device does not require programming or setup.

13.  Power  Window  Motor  (Express  Down
Feature)  Programming  and  Setup  After
Replacement

Window motor with express down feature must be initialized
after replacement. For details, refer to

11.5.7.4

 

Glass Regulator

Initialization (If Window Express Down Feature Is Available)

.

10-24

Programming and Set Up

Vehicle Control System