9.2.7 Removal and Installation
9.2.7.1 Airbag Control Module Replacement

Removal Procedure

Warning!

Refer to "Battery Disconnect Warning" in "Warnings and
Notices".

FE09-0001b

1.

Disconnect  the  battery  negative  cable.  Refer  to

2.11.8.1

 

Battery Disconnection

.

Note

Start  removal  90s  after  the  battery  negative  is
disconnected.

2.

Remove  the  center  console  cup  holder.  Refer  to

3.3.8.9

 

Shift Lever Replacement

.

3.

Remove the rear air duct.

FE09-0002b

4.

Remove the airbag control module retaining bolts.

5.

Disconnect  the  airbag  control  module  wire  harness
connector and remove the airbag control module.

Safety Protection Device

Airbag System

9-31

Installation Procedure:

FE09-0002b

1.

Install the airbag control module retaining bolts.

Torque: 8 Nm (Metric) 5.9 lb-ft (US English)

2.

Connect  the  airbag  control  module  wiring  harness
connector.

FE09-0003b

3.

Install the rear air duct.

4.

Install the center console cup holder.

5.

Connect the battery negative cable.

9.2.7.2 Driver Front Airbag Replacement

Removal Procedure

Warning!

Refer to "Battery Disconnect Warning" in "Warnings and
Notices".

9-32

Airbag System

Safety Protection Device

FE09-0005b

1.

Disconnect  the  battery  negative  cable.  Refer  to

2.11.8.1

 

Battery Disconnection

.

Note

Start  removal  90s  after  the  battery  negative  is
disconnected.

2.

Remove the driver front airbag retaining screws on both
sides.

Warning!

Refer  to  "Supplement  Protection  System  Warning"  in
"Warnings and Notices".

FE09-0006b

3.

Disconnect  the  clock  spring  and  the  driver  front  airbag
wiring harness connector.

4.

Disconnect  the  horn  wiring  harness  connector  and
remove the driver front airbag.

Installation Procedure:

FE09-0007b

1.

Connect the horn harness connector and the clock spring
harness connector.

2.

Tighten  the  driver  front  airbag  retaining  screws.  Before
tightening  the  retaining  screws,  preload  the  retaining
screws first.

Torque: 9 Nm (Metric) 6.6 lb-ft (US English)

3.

Connect the battery negative cable.

Safety Protection Device

Airbag System

9-33

9.2.7.3 Clock Spring Replacement

Removal Procedure

Warning!

Refer to "Battery Disconnect Warning" in "Warnings and
Notices".

FE09-0008b

1.

Disconnect  the  battery  negative  cable  and  wait  for  the
90s. Refer to 

2.11.8.1

 

Battery Disconnection

.

2.

Adjust the steering wheel to a straight state and locked.

3.

Remove  the  driver  front  airbag.  Refer  to 

9.2.7.2

 

Driver

Front Airbag Replacement

.

4.

Remove  the  steering  wheel.  Refer  to 

7.3.6.3

 

Steering

Wheel Replacement

.

5.

Remove  the  steering  column  upper  and  lower  shield
panels. 

Refer 

to 

11.4.8.1

 

Headlamp 

Switch

Replacement

.

FE09-0009b

6.

Disconnect  the  clock  spring  harness  connector  and
remove the clock spring.

9-34

Airbag System

Safety Protection Device