4.4.5 Removal and Installation
4.4.5.1 Wheel Replacement

Removal Procedure:

4

5

1

2
3

FE04-0001b

1.

Loosen wheel nut.

2.

Lift and support the vehicle.

3.

Remove the wheel nut.

4.

Remove the wheel.

Installation Procedure:

1.

Install the wheel.

2.

Install the wheel nuts according to the sequence 1-5-2-4-3
as shown in the graphic, slightly tighten the nuts.

3.

Lower the vehicle.

4.

Tighten  the  wheel  nuts  according  to  the  sequence
1-5-2-4-3 as shown in the graphic.

Torque: 110 Nm (Metric) 81.4 lb-ft (US English)

4.4.5.2 Front Toe Adjustment

Note

Make sure that the vehicle is parked on a even ground.
Make  sure  that  the  front  wheels  are  in  the  straight
position.

Suspension System

Wheels and Tires

4-73

1

2

FE04-0002b

1.

Check both ends of toe settings.

Equipment: Wheel Positioning System

2.

Lift and support the vehicle.

3.

Release rod retaining nuts at both ends.

4.

Clockwise or counter-clockwise rotate the same amount
at both ends to adjust the front toe setting (2).

5.

Tighten the rod retaining nuts at both ends.

4-74

Wheels and Tires

Suspension System

5 Transmission / Axle

5.1 Warnings and Notices.....................5-2

5.1.1 Warnings and Notices...........................................5-2

5.2 Differential.......................................5-3

5.2.1 Specifications...........................................5-3

5.2.1.1 Fastener Tightening Specifications....................5-3

5.2.2 Disassemble View....................................5-4

5.2.2.1 Disassemble View..............................................5-4

5.2.3 Diagnostic Information and Procedures.....5-
5

5.2.3.1 Fault Symptom Table.........................................5-5

5.2.4 Removal and Installation..........................5-6

5.2.4.1 Differential Disassemble and Assemble.............5-6

5.3 Drive Shaft System.......................5-12

5.3.1 Specifications.........................................5-12

5.3.1.1 Fastener Tightening Specifications..................5-12

5.3.2 Disassemble View..................................5-13

5.3.2.1 Disassemble View............................................5-13

5.3.3 Diagnostic Information and Procedures.....5-
14

5.3.3.1 Fault Symptom Table.......................................5-14

5.3.4 Removal and Installation........................5-15

5.3.4.1 Drive Shaft Replacement.................................5-15
5.3.4.2 Drive Shaft Oil Seal Replacement....................5-19

5.3.5 Special Tools and Equipment.................5-21

5.3.5.1 Special Tool List...............................................5-21

Transmission / Axle

Table of Contents

5-1

5.1 Warnings and Notices

5.1.1 Warnings and Notices

Assistant Driving Warning

Warning!

Warning: An assistant should drive the vehicle while the
technician  checks  for  the  location  of  the  reported
condition. Otherwise, personal injury could result.

Battery Disconnect Warning

Warning!

Warning:  Unless  directed  otherwise,  the  ignition  and
start switch must be in the OFF or LOCK position, and
all  electrical  loads  must  be  OFF  before  servicing  any
electrical  component.  Disconnect  the  negative  battery
cable  to  prevent  an  electrical  spark  should  a  tool  or
equipment  come  in  contact  with  an  exposed  electrical
terminal. Failure to follow these precautions may result
in  personal  injury  and/or  damage  to  the  vehicle  or  its
components.

Road Test Warning

Warning!

Warning: Road test a vehicle under safe conditions and
while  obeying  all  traffic  laws.  Do  not  attempt  any
maneuvers that could jeopardize vehicle control. Failure
to  adhere  to  these  precautions  could  lead  to  serious
personal injury and vehicle damage.

Engine Lifting Notice

Note

Notice: When raising or supporting the engine for any
reason, do not use a jack under the oil pan, any sheet
metal, or the crankshaft pulley. Lifting the engine in an
unapproved manner may cause component damage.

5-2

Warnings and Notices

Transmission / Axle